modway MOD-5436 User manual

Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 4
MOD-5436/5437 FULL/QUEEN BED
Thank you for purchasing the MODWAY FULL/QUEEN BED！
Before you start, here are some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the bed, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximately assembly time: 45 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that has been provided.
6.Please keep all fitting out of reach of children.
Hardware:
Component:
AShort Bolt M6x20mm x28
EArc Washer x4
FRubber Insert x16
GAllen Wrench x1
1Headboard x1 2Footboard x1
3Side Rail x2 4Double Slat x4
5Single Slat x8 6Low Post x2
7Center Rail x1 8Support Leg x4
BMedium Bolt M6x35mm x4
CLong Bolt M6x50mm x4
HOpen Wrench x1
DNut M6 x8
1
6
2
3
3
46
4
4
4
5
5
5
7
8
8
88

with
M Bolt (B) Support Legs (8)
Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 4
MOD-5436/5437 FULL/QUEEN BED
Ax4 Ex4 Gx1
STEP 1:
Insert Low Post (6) into Headboard (1) as shown.
Attach by using Arc Washer (E) and Short Bolt (A) from the holes on the back of Low Post (6) and Headboard (1).
Use Allen Wrench (G) to tighten Short Bolts (A) clockwise until secure.
Hardware & Tool required
STEP 2:
Backwith holes
1
6
A1
E
AE
G
6
A
A
6
1
Take off the protective plastic caps from the bottom of Headboard (1)
7
Bx4 Dx4
Gx1 Hx1
8
8
8
8
Hardware & Tool required
7
D
G
B
8
H
Insert 4 pieces of into the 4 holes on Center Rail (7)
Please pay attention to the holes ’direction.
Tighten Nut (D) by using Allen Wrench (G)
and Open Wrench (H) untll secure.
to connect it with as shown.
Medium
M Bolt (B)
Medium

Allen Wrench (G).
Short Bolts (A)
Short Bolts (A).
Double Slatys (4)
RUUubber Insert (F)
Single Slats (5)
Insert one end of
Single S;latys (5)
Double Sltas (4).
Open Wrench (H).
Allen Wrench (G)
Double Slats (4)
Double Slats (4)
Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 4
MOD-5436/5437 FULL/QUEEN BED
STEP 4:
STEP 3:
.
4
4
4
7
8
5
Cx4 Dx4 Gx1 Hx1
Take out
into .then insert them into the crossponding holes on 1 piece of
Side Rail (3) as shown.
Attach assembled to the Side Rail (3) by using
Tighten with .
Repeat above for the other Side Rail (3).
Hardware & Tool required
4
4
4
4
7
83
3
5
5
3
4
A
AG
Ax16 Gx1
Hardware & Tool required
G
C
4
78
H
Take out all and place them as shown.
Attach to the Center Rail (7) by using Bolts (C) and Nuts (D).
Do not fully tighten
Long Bolts (C) and Nuts (D) with and
Please pay attention to the holes’direction on the
Long Bolts (C)
at this step.
Tighten
5
F
and place them as shown.
D
Do not fully tighten Short Bolts (A) at this step.

A
G
6
3
6
A
3
6
A
6
6
2
1
Top Hole
Bottom Hole
Notch
3
3
STEP 5:
Insert Bolts (A) into the bottom holes on the assembled Headboard (1&6) & Footboard (2) by hand.
Leaving 0.3~0.4inch space of the thread of Bolts (A) as shown.
Insert the notch of assembled Side Rails(3&4&5) into the space left on the Bolts (A).
Screw Bolts (A) into the top holes on the assembled Headboard (1&6) & Footboard (2) as shown.
Bolts (A) with Allen Wrench (D) after all assembled.
0.3~0.4inch
STEP 6:
Fix
Customer Service 908-368-1025︱www.modwayfurniture.com Page 4 of 4
MOD-5436/5437 FULL/QUEEN BED
.
AX8 Gx1
Hardware & Tool required
Please fully tighten all .
at this step.
Assembly is complete. Your bed is ready to be enjoyed now!
Bolts (A&C)