modway MOD-5804 User manual

MOD-5804 QUEEN BED
Customer Service 908-368-1025︱www.modway.com Page 1 of 5
Thank you for purchasing the MODWAY QUEEN BED!
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the bed, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe and
environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all fitting out of reach of children.
Hardware:
Components:
1. Headboard x1 2. Footboard x1
6. Center Plastic Cover x13 7. Side Plastic Cover x26 8. Slat x26 9. Slat Support x2
10. No.10 Leg x4 11. No. 11 Leg x4
10
1
3
3
2
11
Bolt M8x50mm x10
Bolt M8x25mm x28
Bolt M8x20mm x10
Flat Washer x48
Lock Washer x48
Screw 25mm x32
Allen Wrench x1
A.
B.
C.
D.
E.
F.
G.
H. Screw Driver x1(Not Included)
3. Bed Rail x2 4.Center Rail x1 5. Center Support Leg x3

MOD-5804 QUEEN BED
Customer Service 908-368-1025︱www.modway.com Page 2 of 5
STEP 1:
10
11
HEADBOARD BOTTOM
11
10
10
11
THIS FACE：BIGGER CURVE TO OUTSIDE
THIS FACE：BIGGER CURVE TO OUTSIDE
1. Turn Headboard (1) and Footboard (2) flat on the carpeted or padded area. Please take out 4 pieces of No. 10
Legs (10) and 4 pieces of No.11 Legs (11) from the carton, then follow the figure below to match the right Leg to
the bottom of the Headboard (1) and Footboard (2), please note that there are corresponding labels with
Numbers shown on the actual Legs and Headboard/Footboard. The bigger curve face of the 4 pieces of No. 10
Legs (10) and 4 pieces of No.11 Legs (11) should face certain direction to the outside.
2. Attach 1 piece of No.10 Leg (10) to the bottom of the Footboard (2) by using 2 pieces of Bolts (B), 2 pieces of
Lock Washers (E) and 2 pieces of Flat Washers (D). Tighten Bolts (B) by using Allen Wrench (G) as shown,
then use 4 pieces of Screws (F) to screw in from No. 10 Leg (10) to the bottom of Footboard (2) by Screw
Driver (H) (Not included).
3. Repeat the same steps for the assembly of the other 7 pieces of Legs.

MOD-5804 QUEEN BED
Customer Service 908-368-1025︱www.modway.com Page 3 of 5
B
x 16
x 16
E
x 16
D
G
x 1
x 32
F
Phillips Head Screwdriver
NOT INCLUDED
BE
BED
10
11
11
2
11
11
10
10
10
10
10
10
FOOTBOARD FRONT

MOD-5804 QUEEN BED
Customer Service 908-368-1025︱www.modway.com Page 4 of 5
STEP 2:
STEP 3:
B
x 12
x 12
E
x 12
D
G
x 1
A
x 10
x 10
E
x 10
D
G
x 1
1
2
10
3
b
f
1
2
3
This side UP
b
f
Back to footboard
Front to headboard
Attach one end of Bed Rail (3) to the Headboard (1) by using 3 pieces of Bolts (B), 3 pieces of Lock Washers (E)
and 3 pieces of Flat Washers (D). Do not fully tighten Bolts (B) at this step.
Repeat the same steps for the other end of Bed Rail to the Footboard (2).
Repeat the same steps for the other Bed Rail to Headboard (1) and Footboard (2).
Finally tighten all the Bolts (B) fully.
1. Attach one of the Slat Support (10) to one of the middle of the Bed Rail (3) by using 5 pieces of Bolts (A), 5
pieces of Lock Washers (E) and 5 pieces of Flat Washers (D). Please pay attention that the Slat Support (10)
with holes is on the top. Tighten Bolts (A) by using Allen Wrench (G) as shown.
2. Repeat the same steps for the other Slat Support (10) to the other Bed Rail (3).

MOD-5804 QUEEN BED
Customer Service 908-368-1025︱www.modway.com Page 5 of 5
STEP 4:
STEP 5:
C
x 10
x 10
E
x 10
D
G
x 1
3
4
2
1
36
8
8
7
7
1
2
3
Insert the assembled Side Plastic Covers (7) into the corresponding holes on the Slat Support (7) of the Bed Rail
(10), and the assembled Center Plastic Cover(6) into the corresponding holes on Center Rail (4) as shown.
Assembly is complete. The Queen Bed is ready to enjoy now!
1. Attach each Center Support Leg (5) to the Center Rail (4) by using 2 pieces of Bolts (C),2 pieces of Lock
Washers (E) and 2 pieces of Flat Washers (D). Tighten Bolts (C) by using Allen Wrench (G) fully as shown in
Figure 1.
2. Attach the Center Rail (4) to the Headboard &Footboard by using 4 pieces of Bolts (C), 4 pieces of Lock
Washers (E) and 4 pieces of Flat Washers (D). Tighten Bolts (C) by using Allen Wrench (G) fully as shown in
Figure 2.
3. Please note that the bottom of each Center Support Leg (5) has the adjustable foot glide which you can adjust
the height if necessary.