modway Raleigh EEI-3575 User manual

EEI-3575 TABLE
Customer Service 609-256-9000︱www.modway.com
Page 1 of 4
Thank you for purchasing the MODWAY Table.
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2. Owing to the size and weight of the Table, we recommend that it is assembled by two adults, on a carpeted
or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3. Please do not use any tools other than those provided or recommended in these instructions.
4. Please do not throw away any of the packaging or the instruction until you have checked all the components
and hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
and environmentally friendly way.
5. Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten
the components from time to time, so please save the tools that have been provided.
6. Please keep all pieces out of reach of children.
Hardware:
Components:
Long Bolt M10*1010mm x1
Nut M10 x1
1. Frame x1 2. Support x1 3. Base x1 4. Top Panel x1
Allen Wrench M4 x1
A.
Spring Washer M10 x1
Flat Washer M10 x1
Glass Top x1
Short Bolt M4*4mm x2
B.
C.
D.
E.
F.
G.

EEI-3575 TABLE
Customer Service 609-256-9000︱www.modway.com
Page 2 of 4
STEP 1:
1 .Please put Frame (1) upside down on a carpeted or padded surface.
2. Insert the Long Bolt (A) with fixed Nut into the pre-drilled holes on the Frame (1) as shown.
3. Tighten Long Bolts (A) clockwise until secure by hand.
STEP 2:
Insert the Support (2) into the Frame (1) through Long Bolt (A) as shown by hand.

EEI-3575 TABLE
Customer Service 609-256-9000︱www.modway.com
Page 3 of 4
STEP 3:
1. Insert the Base (3) into the Support (2) as shown by hand.
2. Attach Base (3) to the Support (2) by using 1 piece of Nut (B) with 1 piece of Spring Washer (D) and
1 piece of Flat Washer (C) as shown.
3. Use Glass Top (E) to tighten Nut (B) as shown.Don’t tight Nut (B) fully.
STEP 4:
1. Rotate the Support (2) to assure the hole on the Frame (1) is aligned with the hole on the Support (2),
insert 1 piece of Bolt (F) to the hole and use Allen Wrench (G) to tighten Bolt (F) as shown. Don’t tight
Bolt (F) fully.
2. Rotate the Base (3) to assure the hole on the Support (2) is aligned with the hole on the Base (3),
insert 1 piece of Bolt (F) to the hole and use Allen Wrench (G) to tighten Bolt (F) as shown. Don’t tight
Bolt (F) fully.
3. When Support (2) and Base (3) are fixed, please fully tighten Nut (B) and all Bolts (F).

EEI-3575 TABLE
Customer Service 609-256-9000︱www.modway.com
Page 4 of 4
STEP 5:
1. Carefully turn over the assembled table by two adults.
2. Carefully put Top Panel (4) on the Frame (1) as shown. Make sure the Top Panel (4) fits the Frame (1).
Assembly is complete. Your Table is ready to enjoy now!
Attention:
If the Table is not stable, you
may adjust it by alignment pin.