Moeller EASY 412-DC Series Setup guide

Training Guide
EASY 412-DC-... EASY 618-AC-RC
EASY 412-AC-... EASY 620-DC-TC
Control Relay
06/99 AWB 2528-1316 GB
1st published 1998, edition 04/98
2nd published 1999, edition 06/99
see list of revisions on page II
© Moeller GmbH, Bonn
Author: Dieter Bauerfeind
Editor: Jörg Eiserloh, Thomas Kracht
Translator: Terence Osborn
For Immediate Delivery call KMParts.com at [phone]

Caution!
Dangerous electrical voltage!
Before commencing the installation
●Disconnect the power supply of the
device.
●Ensure that the device cannot be
accidentally restarted.
●Verify isolation from the supply.
●Earth and short circuit.
●Cover or enclose neighbouring units that
are live.
●Follow the engineering instructions
(AWA) of the device concerned.
●Only suitably qualified personnel may
work on this device/system.
●Before installation and before touching
the device ensure that you are free of
electrostatic charge.
●Connecting cables and signal lines
should be installed so that inductive or
capacitive interference do not impair the
automation functions.
●Install automation devices and related
operating elements in such a way that
they are well protected against
unintentional operation.
●Suitable safety hardware and software
measures should be implemented for
the I/O interface so that a line or wire
breakage on the signal side does not
result in undefined states in the
automation devices.
●Ensure a reliable electrical isolation of
the low voltage for the 24 volt supply.
Only use power supply units complying
with IEC 60 364-4-41 or HD 384.4.41 S2.
●Deviations of the mains voltage from the
rated value must not exceed the
tolerance limits given in the
specifications, otherwise this may cause
malfunction and dangerous operation.
●Emergency stop devices complying with
IEC/EN 60 204-1 must be effective in all
operating modes of the automation
devices. Unlatching the emergency-stop
devices must not cause uncontrolled
operation or restart.
●Devices that are designed for mounting
in housings or control cabinets must only
be operated and controlled after they
have been installed with the housing
closed. Desktop or portable units must
only be operated and controlled in
enclosed housings.
●Measures should be taken to ensure the
proper restart of programs interrupted
after a voltage dip or failure. This should
not cause dangerous operating states
even for a short time. If necessary,
emergency-stop devices should be
implemented.
IBM is a registered trademark of International
Business Machines Corporation.
All other brand and product names are
trademarks or registered trademarks of the
owner concerned.
All rights reserved, including those of the
translation.
No part of this manual may be reproduced in
any form (printed, photocopy, microfilm or
any otherprocess) or processed, duplicated
or distributed by means of electronic
systems without written permission of
Moeller GmbH, Bonn.
Subject to alterations without notice.
For Immediate Delivery call KMParts.com at [phone]

II
06/99 AWB 2528-1316 GB
List of revisions for the manual AWB 2528-1316 GB
Edition Page Title New Modified Omitted
06/99 gen. EASY 620-DC-TC
EASY 618-AC-RC ҂
4Functions ҂
5 “easy” at a glance ҂
6Mounting ҂
6 ff. Connecting “easy” ҂
12 EASY 6... status display ҂
14,
23 ff. Circuit diagram elements ҂
16 System menu ҂
20 Menu languages ҂
22 Startup behaviour ҂
36 Text display (markers) ҂
44 Available memory cards ҂
44 EASY-SOFT ҂
45 Technical data ҂
47 Dimensions of EASY 6... ҂
For Immediate Delivery call KMParts.com at [phone]

1
06/99 AWB 2528-1316 GB
Contents
1 “easy” Control Relay 3
Simply “easy” 3
Mounting “easy” 6
Connecting “easy” 6
“easy” operating principle 11
2 Drawing a Circuit with “easy” 19
Operation of “easy” 19
Setting the menu language 20
Setting the time 21
Choose “easy” operating mode 22
“easy”-Circuit diagram elements 23
Example: creating a circuit diagram 26
Function relay types 30
Example: using a function relay 37
Basic circuits 41
3 “easy” Interface Socket 43
4 Technical Data 45
Technical data 45
“easy” models 45
Index 49
For Immediate Delivery call KMParts.com at [phone]

Contents
2
06/99 AWB 2528-1316 GB
For Immediate Delivery call KMParts.com at [phone]

3
06/99 AWB 2528-1316 GB
1 “easy” Control Relay
Safety information
Simply “easy” Clever switching and controlling
“easy” is a compact, user-friendly and low-cost
control relay for simple control applications.
Applications range from building and domestic
automation to machine and plant control. “easy” has
built-in user-friendly operating elements and an LCD
display.
Just connect up “easy” and draw your circuit
diagram on the display by pressing the buttons on
the device. “easy” works with make contacts, break
contacts, and relays.
Danger of injury due to electric shock!
The electrical installation and commissioning
work must only be carried out by suitably
qualified personnel.
Do not work on the device when the power is
switched on.
Observe the relevant safety regulations:
Switch off the power
Make sure that the device cannot be
switched on again inadvertently
Check to make sure that no dangerous
voltages are present before working on the
device
Cover up any neighbouring equipment which
carries dangerous voltages
For Immediate Delivery call KMParts.com at [phone]

“easy” Control Relay
4
06/99 AWB 2528-1316 GB
Enter your circuit diagram in “easy” just like you
sketched it on paper. “easy” has basic and advanced
functions for relays, time switches and contactors,
and lots more, too. You can make changes to your
circuit just by pressing the buttons on the device.
Time consuming rewiring is not necessary.
Applications everywhere
Building and domestic automation, controllers for
lighting, doors, window shutters...
Control ventilators, rotating doors, greenhouses,
exterior lighting, window controllers, shop display
lighting control...
Create controllers for temperature, ventilation and
brightness levels...
Control machines and plant, presses, conveyor
belts, oscillating conveyors, sorters, pumps...
Additional functions
With the help of the additional 600 units -
EASY 620-DC-TC, EASY 618-AC-RC - as well as the
expansion of the 400 range with EASY 412-DC-TC,
EASY 412-DC-TCX and EASY 412-AC-RCX,
additional I/O and functions are now available, such
as retentive counters, timing relays, markers and
eight user-definable display texts.
The individual features of each control relay are
described below.
For Immediate Delivery call KMParts.com at [phone]

Simply “easy”
5
06/99 AWB 2528-1316 GB
Overview of “easy”
aPower supply
bInputs
cButtons
dSocket for memory card or PC interface cable
eOutput terminals
fLCD display
DEL ALT
ESC OK
b
a
g
f
ESC OK
DEL ALT
d
c
e
For Immediate Delivery call KMParts.com at [phone]

“easy” Control Relay
6
06/99 AWB 2528-1316 GB
Mounting “easy” Mounting on top-hat rail
Hook “easy” to the top edge
of the top-hat rail and hinge
into place while pressing
down slightly as shown by the
arrows.
“easy” will clip into place and
will be secured by the built-in
spring mechanism without
needing screws.
Mounting on a mounting plate
“easy” can be screwed to a mounting plate with the
three device feet (available as an optional accessory).
Connecting “easy” Overview
1.
2.
EASY... 412-DC-R... 412-DC-TC 412 AC-R... 618-AC-RC 620-DC-TC
Connecting inputs Page 7 Page 7 Page 7 Page 9 Page 9
Connecting outputs Page 8 Page 8 Page 8 Page 10 Page 10
For Immediate Delivery call KMParts.com at [phone]

Connecting “easy”
7
06/99 AWB 2528-1316 GB
Inputs EASY 412-DC-...
Inputs EASY 412-AC-...
+10 V
0 V
10 V
5 V
0 V
+24 V
˜
0510
0 V
Ue= 24 V
(20.4–28.8 V )
Ie= 80 mA
+24 V
0 V l7, l8
> 1 A
0 V l1 I2 I3 I4 I5 I6 I7 I8
1 ⭌15 V
0 ⬉5 V
l = 2 mA/24 V
I7, I8 = 2.2 mA/24 V
⬉0.5 Nm
3.5 mm
NL
⬉0.5 Nm
3.5 mm
L
N
> 1 A
Nl1 I2 I3 I4 I5 I6 I7 I8
Ue= 115/230 V ⵑ
50/60 Hz
(97–264 V ⵑ)
le= 40 mA 115 V
20 mA 230 V
l1–I6 = 0.5 mA 230 V
l1–I6 = 0.25 mA 115 V
I7, I8
l = 6 mA 230 V
l = 4 mA 115 V
1 ⭌79 V
0 ⬉40 V
264 V
For Immediate Delivery call KMParts.com at [phone]

“easy” Control Relay
8
06/99 AWB 2528-1316 GB
Outputs EASY 412-AC-..., EASY 412-DC-R...
Outputs EASY 412-DC-T...
0 V , N
⬉8 A/B 16
L1, L2, L3 (115/230 V ⵑ)
+ 24 V
⬉25.000
RL
24 V 8 A
115 V ⵑ8 A
230 V ⵑ8 A
2 A
2 A
2 A
1000 W
10 ⫻58 W
12121212
⬉ 10 000 000
Q1 Q2 Q3 Q4
Suppressor circuit
0 V
RL
24 V 0.5 A
+24 V +24 V 0 V 0 V Q1 Q2 Q3 Q4
⬉10 A
0.5 A
5 W/24 V
⭌2.5 A
+ 24 V
20.4–28.8 V
0 V
Q..
+ 24 V
U⬉33 V
z
0 V
Q..
For Immediate Delivery call KMParts.com at [phone]

Connecting “easy”
9
06/99 AWB 2528-1316 GB
Inputs EASY 620-DC-TC
Inputs EASY 618-AC-RC
+10 V
0V
10 V
5V
0V
+24 V 050 100
0V
⬉ 0.5 Nm
3.5 mm
Ue= 24 V
(20.4–28.8 V )
Ie= 140 mA
+24 V
0V
l7, I8
> 1 A
0V l1 I2 I3 I4 I5 I6 I7 I8
1 ⭌ 15 V
0 ⬉5 V
24 V
I7, I8 = 2.2 mA
I9 I10 I11 I12
28.8 V
24 V
I1–I6, I9–I12 = 3.3 mA
24 V Input 24 V
ⵑ
NL
⬉0.5 Nm
3.5 mm
L
N
> 1 A
Nl1 I2 I3 I4 I5 I6 I7 I8 I9 I10 I11 I12
Ue= 115/230 V ⵑ
50/60 Hz
(85–264 V ⵑ)
115/230 V ⵑInput 115/230 V ⵑ
le= 70 mA 115 V
35 mA 230 V
l1–I6, I9 –I12 = 0.5 mA 230 V
l1–I6, I9 –I12 = 0.25 mA 115 V
I7, I8
l = 6 mA 230 V
l = 4 mA 115 V
1 ⭌79 V
0 ⬉40 V
264 V
For Immediate Delivery call KMParts.com at [phone]

“easy” Control Relay
10
06/99 AWB 2528-1316 GB
Outputs EASY 618-AC-RC
Outputs EASY 620-DC-TC
0 V , N
⬉8 A/B 16
L1, L2, L3 (115/230 V ⵑ)
+ 24 V
⬉ 25.000
R
24 V
8A
115 V ⵑ8 A
230 V ⵑ 8A
2A
2A
2A
1000 W
10 ⫻58 W
12 2 2 2 2 2
11111
⬉10 000 000
Q6Q5Q4Q3
Q2
Q1
Suppressor circuit
+ 24 V
R
5 W/24 V
0.5
0 V
+24 V 0 V Q1 Q2 Q3 Q4 Q5 Q6 Q7
⭌2.5 A
(20.4–28.8 V )
⬉10 A
24 V 0.5 A
Q8
0 V
Q..
+ 24 V
U⬉33 V
z
0 V
Q..
For Immediate Delivery call KMParts.com at [phone]

“easy” operating principle
11
06/99 AWB 2528-1316 GB
“easy” operating
principle
“easy” operating buttons
Moving through menus and choosing values
DEL: Delete object in the circuit diagram
ALT: Special functions in the circuit
diagram
Cursor buttons úíÍÚ:
Move cursor,
Select menu item,
Choose contact numbers, values, time etc.
OK: Next menu level, store your entry
ESC: Last menu level, cancel your entry
AL T
DELDELDELDELDELDELDELDELDELDEL
ESC OK
and
Show system menu
Go to next menu level
Select menu item
Store your entry
Return to last menu level
Cancel your entry since the last OK
ÍÚ
úí
Change menu item
Change value
Change position
P button function (if enabled):
ú
íInput P1,
Input P3,
Í
ÚInput P2
Input P4
For Immediate Delivery call KMParts.com at [phone]

“easy” Control Relay
12
06/99 AWB 2528-1316 GB
EASY 412-...status display
Status displayEASY 618-..., EASY 620-...
Menu display
Inputs
Weekday
Time
Output
terminals
RUN/STOP mode
âOn/ #Off
I12345678
ââ###### MO
â### 12:50
Q1234 RUN
Inputs
Retention Debounce/P buttons
Day, time Stop mode
Output
terminals
Mode
1, 2, 5, 8 On/.Off
1...5..8....
RE I P
MO 02:00 ST
.2..5..8 RUN
Current choice
blinks in the
“easy” menu
Main menu with and without password option
PROGRAM...
PROGRAM..
PARAMETER
SET CLOCK..
PASSWORD..
PROGRAM..
PARAMETER
SET CLOCK..
For Immediate Delivery call KMParts.com at [phone]

“easy” operating principle
13
06/99 AWB 2528-1316 GB
Cursor display
Circuit diagram menu
The cursor blinks alternately:
Full blinking cursor ê/:
Move cursor with úí ,
In circuit diagram also with
ÍÚ
Value M/M
Change position with úí
Change values with ÍÚ
Blinking values/menus are
shown grey in this manual.
Contacts Coil field
Circuit
connections/
Current paths
WINTER TIME
DAY : MO
TIME : 01ê25
WINTER TIME
DAY : MO
TIME : 01:25
I1-I2uT1-ÄQ1
I2-Ö1kêê êêê
êê êê êê êêê
êê êê êê êêê
Connections
For Immediate Delivery call KMParts.com at [phone]

“easy” Control Relay
14
06/99 AWB 2528-1316 GB
Circuit diagram symbols
1 Only EASY 618/620
PCursor button as input
IContact for input
QContact for output
MContact for marker relay
TContact for timer relay
CContact for counter relay
ÖContact for time switch
AAnalog comparator contact
DContact for text marker relay1
:Contact for jump relay 1
RReserve contact for relay1
SContact for marker relay1
Coil field
1st circuit connection
2nd circuit connection
3rd circuit connection
. . .
41st circuit connection
. . .
121st circuit connection1
I1-M2uT1-ÄQ1
I2-Ö1kêê êêê
êê êê êê êêê
êê êê êê êêê
For Immediate Delivery call KMParts.com at [phone]

“easy” operating principle
15
06/99 AWB 2528-1316 GB
Menu structure
Main menu without optional password protection
PROGRAM
DELETE PROG
CARD...
Parameters
Main menu
Parameter set
Parameter display
SET CLOCK
SUMMER TIME
EASY - CARD
CARD-> EASY
DELETE CARD
PROGRAM...
RUN
PARAMETER
SET CLOCK..
DELETE ?
REPLACE ?
PROGRAM
DELETE PROG
CARD...
PROGRAM
DELETE PROG
CARD...
EASY - CARD
CARD->EASY
DELETE CARD
DELETE ?
EASY - CARD
CARD-> EASY
DELETE CARD
RUN
PROGRAM..
PROGRAM...
RUN
PARAMETER
SET CLOCK..
PROGRAM...
RUN
PARAMETER
SET CLOCK..
REPLACE ?
SUMMER TIME
WINTER TIME
SET CLOCK
SUMMER TIME
STOP
STOP: Circuit diagram menu
RUN: Power flow display
RUN Parameter
display
Circuit diagram
Display for
clock setting
WINTER TIME
DAY : MO
TIME :
14:05
PROGRAM...
RUN
PARAMETER
SET CLOCK
For Immediate Delivery call KMParts.com at [phone]

“easy” Control Relay
16
06/99 AWB 2528-1316 GB
Main menu with password protection
System menu EASY 412-..., operating system V 1.0
Password
Password entry
unlock
“easy”
PASSWORD...
RUN
PARAMETER
SET CLOCK..
Main menu
PASSWORD...
RUN
DELETE ALL
Correct entry
Status display
Four wrong
entries
ENGLISH
GB D F E I
System
CHANGE PW
ACTIVATE
Password entry
Set password
Change password
Password entry
CHANGE PW
ACTIVATE ACTIVATE
DEBOUNCE OFF
DEBOUNCE ON
P BUTTONS ON
P BUTTONS OFF
PASSWORD...
DEBOUNCE OFF
P ON
GB D F E I
PASSWORD...
DEBOUNCE OFF
P BUTTONS ON
GB D F E I
PASSWORD...
DEBOUNCE OFF
P ON
GB D F E I
DEUTSCH
FRANCAIS
ESPANOL
ITALIANO
Password
Password
The menu functions are described in the
User Guide AWB 2528-1304 GB.
PASSWORD...
DEBOUNCE OFF
P ON
GB D F E I
For Immediate Delivery call KMParts.com at [phone]

“easy” operating principle
17
06/99 AWB 2528-1316 GB
System menu EASY 412-..., operating system
from V 1.2, EASY 618-AC-RC, EASY 620-DC-TC
ENGLISH
GB D F E I
System
CHANGE PW
ACTIVATE
Password entry
Set password
Change password
Password entry
CHANGE PW
ACTIVATE ACTIVATE
DEBOUNCE OFF
DEBOUNCE ON
PASSWORD...
SYSTEM
GB D F E I..
PASSWORD...
SYSTEM
GB D F E I..
DEUTSCH
FRANCAIS
ESPANOL
ITALIANO
Password
Password
PASSWORD...
SYSTEM
GB D F E I..
DEBOUNCE OFF
P ON
STOP MODE
RETENTION ON
DEBOUNCE OFF
P ON
STOP MODE
RETENTION ON
DEBOUNCE OFF
P ON
STOP MODE
RETENTION ON
DEBOUNCE OFF
P ON
STOP MODE
RETENTION ON
P ON
P BUTTONS OFF
STOP MODE
RUN MODE
RETENTION ON
RETENTION OFF
PORTUGUES1
NEDERLAND1
SWENSKA1
POLSKI1
TURKCE1
The menu functions are
described in the User Guide
AWB 2528-1304 GB.
1Onl
y
EASY 6/...
For Immediate Delivery call KMParts.com at [phone]