Monarch Water WELLBEING GEMINI User manual

IMPORTANT
READ BEFORE COMMENCING INSTALLATION
UNIT SPECIFICATIONS:
Feed water quality: Municipal tap water
Voltage and frequency: 100-240V, 50/60Hz
Power input: 96W
Purified water flow: 1.2L/Min
Feed water temperature: 5-45 ·c
Feed-water TDS: ≤ 250ppm
Feed-water Chlorine level: ≤ 0.2ppm
Rejection: 90-99%
Feed-water pressure: 0.1-0.4 Mpa
Electric shock resistance: type II
CONTENTS OF PACKAGE:
Reverse Osmosis Unit - 1 pc
Housing Wrench - 1 pc
Food Grade Tubing - 3 pcs (Red, White, Blue)
Faucet - 1 pc
Accessories - Tube Plug, Screws, Drain Clamp, Tee
Fitting,
Ball Valve, Feed Water Valve
RO Membrane - 2 pc
Install manual - 1 pc
ALL GEMINI UNITS MUST BE INSTALLED BY A COMPETENT PERSON.
/ HOW YOUR SYSTEM WORKS
Tee Fitting
/ SCHEMATIC
The symbol above means that according to United Kingdom and European Union member countries
laws and regulations your product and/ or its battery shall be disposed of separately from household
waste.
When this product reaches its end of life, take it to a collection point designated by local authorities.
The separate collection and recycling of your product and/ or its battery at the time of disposal will
help conserve natural resources and ensure that it is recycled in a manner that protects human health
and the environment.
The symbol above means that according to United Kingdom and
European Union member countries laws and regulations your
product and/or its battery shall be disposed of separately from
household waste.
When this product reaches its end of life, take it to a collection
point designated by local authorities. The separate collection and
recycling of your product and/ or its battery at the time of disposal
will help conserve natural resources and ensure that it is recycled in
a manner that protects human health and the environment.
2 3monarchwater.co.uk monarchwater.co.uk

/ FEED WATER VALVE AND TEE FITTING
• Install Tee Fitting Valve shown below to your 15mm cold water pipe.
• Attach the grey plastic adapter to the male thread on the tee fitting.
• Apply sealant to olive as shown in right hand picture below.
• Ensure the compression fittings and the grey fitting are secured tight to seal
• Connect White Feed Water Tubing from unit to Feed Water Valve.
/ WARNING
Ensure chrome nut compression and grey plastic adapter are tight to seal.
/ NOTE
Use only a cold potable water supply as Feed Water, hot water will damage your unit. Softened Feed
Water will extend the life of the RO Membrane.
/ INSTALLING THE BARI TAP
/ DRAIN CLAMP INSTALLATION
Position drain clamp on drain pipe above the drain trap and tighten securely.
Using the drain clamp as a guide, drill a 6mm hole, enough for the 1/4” tubing to pass,
through one side of the drain pipe. DO NOT drill through both sides.
Connect Red Waste Water Tubing from unit to Drain Clamp.
/ NOTE
When cutting the tubing make clean, square, cuts, failing to do so result in poor connection
and possible leaks.
/ WARNING
The lowest point of the line should be the point of connection to the Drain Clamp. There
should be no sag in the line as this may cause excessive noise as the reject water is flowing
to drain.
/ FIRST USE INSTRUCTIONS
1. Connect RO system and adapter, turning the power indicator light on, the buzzer will ring three
times, let the machine flush for 90 seconds. The indicator light will flash slowly and be lit blue .
2. The RO system begins making water with the indicator light flashing. When the system enters
standby mode or when the water tank is full the indicator light is a static blue.
3. When the RO system stops making water, the indicator light is red. The buzzer rings 30 times after
working continuously for 6 hours or a water leak is detected.
Note: Under normal operation, please draw water off for 10-15 minutes for cartridges to flush when
using for the first time.
The faucet should be placed in a convenient area near the sink
tap. There should be a reasonable amount of space above and
below the faucet mounting position to allow to connections to
the RO unit.
There should be a 2” diameter area for the faucet to be
mounted.
The thickness of mounting surface should not exceed 32mm.
Select a convenient location near your sink to place the faucet.
Drill a hole 12mm in diameter into the counter top.
Place washers, plates, seals and nuts in order as per diagram
and tighten on the countertop. Screw the grey plastic adapter
on the bottom of the faucet.
Attach the Blue Pure Water tubing to the grey plastic adapter
on the
bottom of faucet and connect tubing to unit.
4 5monarchwater.co.uk monarchwater.co.uk

6 months
6 months
6 months
6 months
Upon Exhauson
FILTER
REPLACEMENT
(FOR REFERENCE ONLY)
/ NOTE
Cartridge replacement reminder: Filters are to be replaced every 6 months. However, after
working for 50 hours cumulatively, indicator light turns green and buzzer keeps ringing for
10 seconds. Please turn machine off for 15 seconds then turn back on.
/ CARTRIDGES REPLACEMENT AND REMINDER / CARTRIDGE REPLACEMENT
6 7monarchwater.co.uk monarchwater.co.uk

/ SAFETY INSTRUCTIONS
This appliance is intended to operate and function as per the instructions in this manual. It is
not designed to operate outside of the specifications listed and any attempt to do so or tamper
with the unit can cause damage to the unit and/or bodily harm. This unit is not a toy, keep out of
reach from small children. If the unit requires service or repair, please contact your local service
technician or sales representative.
• Please ensure feed water temperature is over 4 °C. Using water below 4 °C can cause ice to
form and damage the unit.
• Please ensure power source is correct before connecting unit. Incorrect voltage could result in
damage to unit and/or fire hazard.
• Do not cause damage to or use unit if the power cord is damaged. A damaged power cord could
cause an electrical shock or fire hazard. If power cord is damaged, unplug and discontinue use
immediately.
/ DISCLAIMER
In case of special circumstances during installation, you need to use accessories not included in the
packing list of this product. Consumers are asked to purchase quality-guaranteed accessories through
regular channels.
Monarch Water is not responsible for the quality of non-original accessories because of the quality
problems of the accessories purchased by consumers. Monarch Water assumes no responsibility for
any water leakage accident.
/ REGULAR MAINTENANCE
Please ensure you change your filters when recommended. Failure to change your filters regularly may
invalidate your warranty. Regularly check the TDS level of your output water.
Ensure that you change your Reverse Osmosis Membrane when recommended or when the TDS level
starts to rise.
For best performance, supply unit with softened water, as this will achieve maximum life expectancy
of the membrane.
/ TROUBLESHOOTING
/ PRECAUTIONS FOR USE
1. Wash and replace cartridges regularly.
2. Do not disassemble parts randomly, it may cause leakage or damage.
3. Do not use power supply with disproportional rated voltage.
4. Please pull the power plug and cut off the feed water valve if long term storage.
5. Do not store or explore in an environment of O”C or below.
6. Handle with care when discharging, moving and installing.
1. Please turn off the feed water ball valve and cut off the source water to avoid the “water
hammer phenomenon” which may lead to leakage or damage to housings and filters if go out
in daytime or after the last use at night. Our company would not take the responsibility of the
consequence caused by this situation.
2. Please cut off power and source water at once in case troubles occur and ask professional staff
to repair.
3. Professional staff are advised to replace cartridges.
4. In state of insufficient water input, indicator light turns yellow and buzzer keeps ringing for 5
seconds.
Note: in the first time running, make sure the system is installed and operated correctly without
any problem bef ore opening the fa ucet. Keep flushing the filters for 10 to 15 minutes before
collecting the first glass of water for drinking.
PS: please let the system working normally for over 90 minutes bef ore any test.
/ REMINDERS
8 9monarchwater.co.uk monarchwater.co.uk

TO ORDER SPARE PARTS
Please contact your dealer for more information.
+ 44 (0) 1986 784759
monarchwater.co.uk
[e-mail]