Monoprice 31055 User manual

Blackbird™ HDBaseT™ Extender Kit
P/N 31055
User's Manual

2
SAFETY WARNINGS AND GUIDELINES
Please read this entire manual before using this device, paying extra attention to these
safety warnings and guidelines. Please keep this manual in a safe place for future reference.
This device is intended for indoor use only.
Do not expose this device to water or moisture of any kind. Do not place drinks or
other containers with moisture on or near the device. If moisture does get in or on
the device, immediately unplug it from the power outlet and allow it to fully dry
before reapplying power.
Do not expose this device to excessively high temperatures. Do not place it in, on,
or near heat sources, such as a fireplace, stove, radiator, etc. Do not leave it in direct
sunlight.
Do not place or install this device in an area where it can be exposed to excessive
amounts of dust, humidity, oil, smoke, or combustible vapors.
Prior to operation, check the unit and power cord for physical damage. Do not use if
physical damage has occurred.
Before plugging the unit into a power outlet, ensure that the outlet provides the
same type and level of power required by the device.
Never unplug the unit by pulling on the power cord. Always grasp the connector
head or adapter body.
Ensure that power is turned off and disconnected before making any electrical
connections.
Take care to prevent damage to the power cord. Do not allow it to become
crimped, pinched, walked on, or become tangled with other cords. Ensure that the
power cord does not present a tripping hazard.
Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or
detergents. For stubborn deposits, moisten the cloth with warm water.
This device has no user serviceable parts. Do not attempt to open, service, or
modify this device.

3
INTRODUCTION
This Blackbird™ HDBaseT™ Extender Kit allows you to distribute a 1080p@60Hz HDMI®
signal to distances up to 492 feet (150 meters) over a single Cat6 Ethernet cable. It supports
bi-directional IR and RS-232 pass-through extension, allowing for control of local video
source device or the remote display. It supports bi-directional 12V Power over Cable (PoC),
simplifying the wiring and allowing for the use of only a single AC power adapter.
FEATURES
Supports resolutions up to 1080p@60Hz
Extends to distances up to 492 feet (150 meters) using a single Cat6 Ethernet cable
Provides up to 10.2 Gbps bandwidth
Supports bi-directional IR and RS-232 pass-through extension
Supports 12V Power over Cable (PoC)
Supports RS-232 firmware updates
CUSTOMER SERVICE
The Monoprice Customer Service department is dedicated to ensuring that your ordering,
purchasing, and delivery experience is second to none. If you have any problem with your
order, please give us an opportunity to make it right. You can contact a Monoprice
Customer Service representative through the Live Chat link on our website
www.monoprice.com during normal business hours (Mon-Fri: 5am-7pm PT, Sat-Sun: 9am-
6pm PT) or via email at [email protected]

4
PACKAGE CONTENTS
Please take an inventory of the package contents to ensure you have all the items listed
below. If anything is missing or damaged, please contact Monoprice Customer Service for a
replacement.
1x Blackbird™ HDBaseT™ transmitter
1x Blackbird HDBaseT receiver
4x Mounting ears
4x Screws
8x Plastic feet
2x 3-pin Euroblock connectors
1x AC power adapter (12 VDC, 1A)
1x User's manual
PRODUCT OVERVIEW
Transmitter
1. POWER LED: The LED illuminates when power is applied.
2. RS-232: 3-pin Euroblock connector for connecting an RS-232 device.
3. HDMI IN: HDMI® connector for connecting the video source device.
4. CTRL/UPDATE: Slider switch for determining the behavior of the RS-232 connection.
When in the CTRL position, RS-232 signals are passed back and forth between the
transmitter and the receiver. When in the UPDATE position, you can perform a
firmware update of the Valens IC program through the RS-232 connection.

5
5. HDBT OUT: RJ45 connector for a Cat6 Ethernet cable to connect the transmitter and
the receiver. The LINK LED illuminates when there is a valid HDBaseT™ link between
the transmitter and the receiver. The HDCP LED illuminates when the video contains
HDCP content.
6. IR IN: 3.5mm jack for connecting an IR receiver (not included).
7. IR OUT: 3.5mm jack for connecting an IR transmitter (not included).
8. DC 12V: DC barrel connector for connecting the included AC power adapter.
Receiver
1. POWER LED: The LED illuminates when power is applied.
2. RS-232: 3-pin Euroblock connector for connecting an RS-232 device.
3. HDMI OUT: HDMI® connector for connecting an HDMI display.
4. CTRL/UPDATE: Slider switch for determining the behavior of the RS-232 connection.
When in the CTRL position, RS-232 signals are passed back and forth between the
transmitter and the receiver. When in the UPDATE position, you can perform a
firmware update of the Valens IC program through the RS-232 connection.
5. HDBT IN: RJ45 connector for a Cat6 Ethernet cable to connect the transmitter and
the receiver. The LINK LED illuminates when there is a valid HDBaseT™ link between
the transmitter and the receiver. The HDCP LED illuminates when the video contains
HDCP content.
6. IR IN: 3.5mm jack for connecting an IR receiver (not included).
7. IR OUT: 3.5mm jack for connecting an IR transmitter (not included).
8. DC 12V: DC barrel connector for connecting the included AC power adapter.

6
SAMPLE CONNECTION DIAGRAM
INSTALLATION
1. Ensure that all equipment to be connected is powered off and unplugged from its
power source.
2. Place or mount the transmitter and receiver in their intended locations.
3. Using a High Speed HDMI® Cable (not included), plug one end into the HDMI input
on your display or projector, then plug the other end into the HDMI OUT connector
on the receiver.
4. (Optional) Plug an IR receiver (not included) into the IR IN jack on the transmitter,
the receiver, or both.
5. (Optional) Plug an IR transmitter (not included) into the IR OUT jack on the
transmitter, the receiver, or both.
6. Plug a Cat6 Ethernet cable (not included) into the HDBT IN jack on the receiver, then
plug the other end into the HDBT OUT jack on the transmitter.

7
7. Using a High Speed HDMI Cable (not included), plug one end into the HDMI IN
connector on the transmitter, then plug the other end into the HDMI output on
your video source device.
8. Plug the DC barrel connector on the included AC power adapter into the DC 12V
jack on either the transmitter or the receiver, then plug the other end into a nearby
AC power adapter. The POWER LED on both the transmitter and receiver should
illuminate, indicating that power has been applied.
9. Plug in and power on all connected equipment. Start video playback on your video
source device and verify that you can see the video on the remote display. If you
are using the IR extension feature, verify that you can control the appropriate
devices with their remote controls.
Congratulations, you have successfully installed your HDBaseT extender kit!
TECHNICAL SUPPORT
Monoprice is pleased to provide free, live, online technical support to assist you with any
questions you may have about installation, setup, troubleshooting, or product
recommendations. If you ever need assistance with your new product, please come online
to talk to one of our friendly and knowledgeable Tech Support Associates. Technical
support is available through the online chat button on our website www.monoprice.com
during regular business hours, 7 days a week. You can also get assistance through email by
sending a message to [e-mail]

8
SPECIFICATIONS
Model
31055
Maximum Resolution
1080p@60Hz
Transmission Method
HDBaseT™
Transmission Distance
Up to 492 feet (150 meters)
Bandwidth
10.2 Gbps
HDMI® Version
1.4
HDCP Version
2.2
Input Power
12 VDC, 1A or Power over Cable (PoC)
AC Adapter Input Power
100 ~ 240 VAC, 50/60 Hz
Power Consumption
9.5 watts
Operating Temperature
+32 ~ +104°F (0 ~ +40°C)
Storage Temperature
+14 ~ +131°F (-10 ~ +55°C)
Relative Humidity
0 ~ 90% RH, non-condensing
Dimensions (each)
3.3" x 4.1" x 0.6" (84 x 104 x 16 mm)
Transmitter Weight
4.8 oz. (135 g)
Receiver Weight
4.9 oz. (140 g)
Blackbird™ is a trademark of Monoprice Inc.
HDBaseT™ and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.
HDMI®, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC in the United States and other countries.
Blu-ray Disc™ and Blu-ray™ are trademarks of the Blu-ray Disc Association.