Montag Gen I 24 Row User manual

1
P002941 - Document - Montag Gen I 24 Row / Wil-Rich 10k / Gladiator Installation Guide - Rev. A - 12/17/2019
Gen I 24 Row / Wil-Rich 10k / Gladiator Installation Guide

2
P002941 - Document - Montag Gen I 24 Row / Wil-Rich 10k / Gladiator Installation Guide - Rev. A - 12/17/2019
HOSE END
-REAR OF TOOLBAR-
PLATFORM END
-FRONT OF TOOLBAR-
PLATFORM END
-FRONT OF TOOLBAR-
HOSE END
-REAR OF TOOLBAR-

3
P002941 - Document - Montag Gen I 24 Row / Wil-Rich 10k / Gladiator Installation Guide - Rev. A - 12/17/2019
HOSE END
-REAR OF TOOLBAR-
PLATFORM END
-FRONT OF TOOLBAR-

4
P002941 - Document - Montag Gen I 24 Row / Wil-Rich 10k / Gladiator Installation Guide - Rev. A - 12/17/2019
PLATFORM END -
REMOVE EXISTING
PLATFORM MOUNTING
HARDWARE AND
REPLACE WITH
BUMPER HARDWARE.
BUMPER END WILL SIT
BETWEEN THE
PLATFORM AND THE
CRADLE. YOU WILL
NEED TO PARTIALLY
DISASSEMBLE THE
PLATFORM TO REPLACE
THE MOUNTING BOLT.
HOSE END
PLATFORM END

5
P002941 - Document - Montag Gen I 24 Row / Wil-Rich 10k / Gladiator Installation Guide - Rev. A - 12/17/2019
12345678910 11 12 13 14 15 16 17 18 19 20 21 22 23 24
30’-0” 30’-0” 30’-0” 30’-0” 30’-0” 30’-0” 30’-0” 30’-0” 30’-0” 30’-0” 30’-0” 30’-0” 30’-0” 30’-0” 30’-0” 30’-0” 30’-0” 30’-0” 30’-0” 30’-0” 30’-0” 30’-0” 30’-0” 30’-0”
123456789
10 11 12 13 14 15
16 17 18 19 20 21 22 23 24
Montag Gen I 24 Row / Wil-Rich 10k / Gladiator Installation Guide

6P002941 - Document - Montag Gen I 24 Row / Wil-Rich 10k / Gladiator Installation Guide - Rev. A - 12/17/2019

7
P002941 - Document - Montag Gen I 24 Row / Wil-Rich 10k / Gladiator Installation Guide - Rev. A - 12/17/2019
A000211 (2)
A000213 (2)
A000212 (2)
(SEE PAGES 2, 6)
OUTER BRACKETS (10)

8
P002941 - Document - Montag Gen I 24 Row / Wil-Rich 10k / Gladiator Installation Guide - Rev. A - 12/17/2019
1
2
34
5
6
7
8
9
10
11
12
13
15
16
17
18
19
20
21
22
23
24
15
10
14

9
P002941 - Document - Montag Gen I 24 Row / Wil-Rich 10k / Gladiator Installation Guide - Rev. A - 12/17/2019
The left side bracket should be
roughly 8-10” from this gusset.
Remove
Swing
ladder from
platform
and install
as shown.

/ Gladiator Row Unit Assembly Instructions
24 Row Mount Kit –A000184AA
Hose routed around
the outside of
springs as shown.
Locate the open side of the
Montag supplied Air Release
up and away from the spring. Montag supplied 1-1/2” hose
and hose clamp –P000238.
Cut hose to 31” long.
Montag supplied
1-1/2” hose clamp –
P000238.
Montag supplied 2-1/2”
hose clamp –P000239.
Montag supplied:
M000849AA –Bracket
P000620 – ½” U-bolt
P000415 – ½” Nut
P000067 – ½” Washer
Montag supplied 2”
hose clamp –P000240
–positioned to restrict
movement of the hose
guide.
Montag supplied hose
guide –M000848.
10P002941 - Document - Montag Gen I 24 Row / Wil-Rich 10k / Gladiator Installation Guide - Rev. A - 12/17/2019

/ J. Assy / Gladiator Blockage Sensor Assembly Instructions
Wireless antenna is
under the words “J.ASSY”
- orient for the least steel
interference between
antenna and monitor.
P002308
Blockage Sensor.
Clamp coupler
over 1-1/2” hose.
Clamp coupler
over air release.
You will want to have the “digital” section of
the sensor orientated for easy access when
programming. This area is used to label the
row number that this sensor is attached to .
Install couplers as shown. It is important to keep couplers in
line with air release and hose as shown. Refer to J. Assy install
guide for setup and programming of monitor and sensors.
Sensor Kits
6 Row –K002053
8 Row –K002031
12 Row –K002032
16 Row –K002033
18 Row –K002034
24 Row –K002035
11P002941 - Document - Montag Gen I 24 Row / Wil-Rich 10k / Gladiator Installation Guide - Rev. A - 12/17/2019

Install hoses in K002353 from tractor to
corresponding ports shown:
K002353:
24 Row: ¾” hose is for pressure.
1” hose is for return.
½” hose is for the zero-pressure
case drain.
Hookup case drain alarm to 12VDC power.
HYDRAULIC COMPONENTS FOR MONTAG GEN I DRY SKID*
* Hookup locations shown for a single section
machine. For a two section machine, the
return port is on the opposite side of the
machine on the smaller hydraulic manifold.
P002941 - Document - Montag Gen I 24 Row / Wil-Rich 10k / Gladiator Installation Guide - Rev. A - 12/17/2019 12