Monte Carlo Fan Company 3ERHR52 D Series Instruction manual

Total fan weight with light
DATE OF PURCHASE:
MODEL NUMBER:
RETAILER NAME:
RETAILER ADDRESS:
Attach sales receipt to this card and retain as yourproof of purchase
To register your fixture, please visit our website www.montecarlofans.com
3ERHR52XXXD Series Fan
CUL Model NO. : 3ERHR52XXXD
7.6 kg
16.72 lbs
Owner’s Guide and Installation Manual

2
© 2022 Monte Carlo Fan Collections 10/2022
Customer Service
800-969-3347
Customer Service Center
7400 Linder Ave.
Skokie, IL 60077
www.montecarlofans.com
Cautions and Warnings
Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70), including
fire-rated construction.
Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side
of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be turned upward and pushed
carefully up into the outlet box.
WARNING: Before you begin installing, servicing or cleaning the fan unit, switch the power off at the service panel and lock the service panel to prevent
the power from being switched back on accidentally. If the service panel cannot be locked to prevent the power from being switched on accidentally,
securely fasten a warning sign to the service panel.
Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor
to the trailing edge of the blade.
WARNING: To reduce the risk of fire, electric shock, or personal injury, mount to outlet box marked “Acceptable for Fan Support of 15.9 kg (35 lbs) or
less” and use mounting screws provided with the outlet box.
CAUTION: Comply with local codes and regulations. If installing the secondary support safety cable in the U.S., do not remove knockouts in the outlet
box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to the building structure or the ceiling joist.
WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert
foreign object between rotating blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
WARNING: To reduce the risk of fire or electric shock, this fan should only be used with fan speed control part no. UC9031 manufactured by Rhine
Electronic Co., Ltd.
WARNING: To reduce the risk of fire or electric shock, do not use this fan with any other solid state fan speed control device, or variable speed control.
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
Never place a switch where it can be reached from a tub or shower.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equipment
manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for
Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
CAUTION: To reduce the risk of electric shock, disconnect the electrical supply circuit to the fan before installing the light kit.
CAUTION: The light source is designed for this specific application and can overheat if serviced by untrained personnel. If any servicing is required, the
product should be returned to an authorized service facility for examination or repair.
All set screws must be checked and tightened where necessary before installation.
Note: Suitable for use in damp locations. Install the fan under covered or enclosed patios or porches.
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Stepladder and Wire Strippers
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING
READ AND SAVE THESE INSTRUCTIONS

3
1 2 3
4 5 6
© 2022 Monte Carlo Fan Collections 10/2022
ON
OFF
ON
OFF
Before you begin installing the fan, Switch
power off at Service panel and lock
service disconnecting means to prevent
power from being switched on
accidentally. When the service
disconnecting means cannot be locked,
securely fasten a warning device, such
as a tag, to the service panel.
Use AC 120V/60HZ power supply
only.
Before installing this fan make sure the
outlet box is properly installed to the
house structure. To reduce the risk of
fire, electric shock, or personal injury,
mount to outlet box or supporting system
acceptable for fan support.
(Mounting must support at least 35 lbs.)
Remove the two set screws provided with
the box, aligning the holes of the
mounting plate with the holes of the
outlet box and reinstall the 2 outlet box
screws securely.
As shown in the illustration, hang the motor
assembly onto the hook of mounting plate for
hands-free wiring and safety cable installation.
Safety cable must be installed into the
house structure using 3” lag screws,
washers, and lock washers provided,
required for outdoor applications and in
Canada (All fans installed in Canada), and
for USA fan and light kit combinations
over 35lbs.
Make sure that when the safety cable is
fully extended the lead wires are longer
than the cable and no stress is placed on
the lead wires.
Note: If Installing The Secondary Support
Safety Cable in the U.S., Do Not Remove
Knockouts In The Outlet Box.
Use metal outlet box suitable for fan
support and use only the screws provided
with the outlet box (must support 35
lbs). Before attaching fan to outlet box,
ensure the outlet box is securely fastened
by at least two points to a structural
ceiling member ( a loose box will cause
the fan to wobble).
Mounting plate
Hook
SAFETY CABLE INSTALLATION
Lag
screw Safety
cable
Washer
Lock washer
Outlet box

4
7 8 9
© 2022 Monte Carlo Fan Collections 10/2022
10 11 12
After making the wire connections, the wires
should be spread apart with the grounded
conductor and the equipment-grounding
conductor on one side of the outlet box and
ungrounded conductor on the other side of
the outlet box. The splices after being made
should be turned upward and pushed carefully
up into the outlet box.
Lift motor assembly, aligning the
captured screws on the plate on top of
fan assembly with the screw holes on
mounting plate. Install set screws to fix
them. Tighten all screws securely.
Align the three notches on the mounting
plate with the three lock tabs on the
housing and turn the housing clockwise
until the lock tabs locked in place.
Install the flywheel onto the motor.
Position the alignment posts on the
flywheel to the round holes in the motor
as shown in the inset.
install the provided set screws to the
other 5 holes in the motor to fix the
flywheel. Tighten all set screws securely.
Insert a blade into the slot in the flywheel.
Ungrounded
wires
Refer to page 7 for wiring,
installation and operation of
Wall controller. Do not operate
the fan or light until it is
installed completely.
Mounting plate
Captured screw
Mounting plate
Housing
Notch
Tab
Flywheel
To Wall
Outlet Box
Black (Live)
Blue White (Neutral) Ground/Green
Ground/Green
White
Black
Blue
Grounded
wires
Blade
Motor
Flywheel
Alignment
post

5
13 14 15
16 17 18
© 2022 Monte Carlo Fan Collections 10/2022
Install blade with screws and washers
provided, aligning each of the holes as
shown and tighten all screws securely.
Repeat this process for remaining blades.
Tighten all screws securely.
Connect the quick connector to the
connector from the light pan. Be sure
plugs connection clasped together firmly.
Attach light pan onto the plate on motor,
Place light pan over the lead wires from
fan, aligning the keyhole slots on the light
pan with the preassembled screws on the
plate. Twist clockwise till lock. Reinstall
the other screw. Tighten all screws
securely.
Loosen 2 and remove 1 preassembled
screw from light pan. Save screw for later
use.
Connect white wire from fan to white wire
from light fixture and then connect blue
(or black) wire from fan to black (or blue)
wire from light fixture. Be sure plugs
connection clasped together firmly.
Attach light fixture onto the light pan,
aligning the keyhole slots on the light
fixture with the preassembled screws on
the light pan. Twist clockwise till lock.
Reinstall the other screw. Tighten all
screws securely.
Install 2 x 9-watt medium base enclosed
type of LED lamps.
Caution: Approved for use with LED light
bulb only (Part No. 97512S).
Do not use incandescent light bulb.
Caution: Do not replace bulb until it
cools down.
Loosen 2 and remove 1 preassembled
screw from the plate on motor. Save
screw for later use.
Plate on motor
Light fixture
Blade Light fan
Blue
Black
White
Bulb

6
© 2022 Monte Carlo Fan Collections 10/2022
19 20
Attach glass by locating dimples in light
pan with grooves on the glass and twist
clockwise until tight.
Setting the reverse switch on the left
hand side will result in downward airflow
and setting the switch on the right hand
side will result in upward airflow.
Note: Reverse switch must be set either
way completely. If the reverse switch is
set in the middle position, fan will not
operate.
Glass
Reverse switch

7
© 2022 Monte Carlo Fan Collections 10/2022
Wall Control Wiring, Installation and Operation
Operation
This wall controller provides 4 fan
speeds, light on/off and light
dimming control.(Fig.2)
1 - High - , 2 - Medium high , 3 -
Medium , 4 - Low , - Off.
Light on/off and dimming.
Warning: Before proceeding, be sure to shut off electricity
at main switch or circuit breaker in order to avoid electrical
shock.
Note: Before installing the wall transmitter, place it in OFF
position. (Fig.2)
Make series-wound connection for the wall controller with
HOT wire from house and lead wires from fan.
Connect the black/white wire marked “AC IN L” from wall
controller to the HOT wire from house and then connect the
black wire marked “TO MOTOR L” of wall controller to the
fan lead wire from fan in outlet box. Connect the blue wire
marked “FOR LIGHT” from wall controller to the light lead
wire from fan (fan with light)
Connect green/yellow grounded wire to grounded wire from
outlet box.
Install the wall controller to outlet box using machine screws
provided.
Attach wall plate to wall control unit with screws provided.
(Fig.1)
Wall plate
Black/White(AC IN L)
Blue (FOR LIGHT)
Black (TO MOTOR L)
120V/60HZ
Power supply
WHITE (Neutral)
BLUE
BLACK
Wall controller
Outlet box
Green/Yellow (Grounding)
BLACK (Live)
Off
ON and Dimming
Fig.1
Fig.2

8
© 2022 Monte Carlo Fan Collections 10/2022
Troubleshooting
or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults,
installation, please call our Customer Service Center at the
number printed on your parts list insert sheet.
Warning
and lock the service panel to prevent the power from being switched back on accidentally. If the service panel
cannot be locked to prevent the power from being switched on accidentally, securely fasten a warning sign to the
service panel.
1. Check main and branch circuit fuses or circuit breakers.
2. Check line wire connections to fan and switch wire connections in switch housing.
CAUTION
either way. Fan will not operate when switch is in the middle.
4. If this fan uses a remote controller, make sure dip switches are in the correct setting
and make sure the battery works.
1. Check to make sure all screws in motor housing are snug (not over tightened).
2. Check to make sure the screws which attach the fan blade holder to the motor are tight.
3. Check to make sure wire nut connectors in switch housing are not rattling against each
other or against the interior wall of the switch housing.
CAUTION
4. Check to be sure lightbulb is tight in socket and not touching the glass shade.
5. Some fan motors are sensitive to signals from Solid State variable speed controls.
6. Allow "break-in" period of 24 hours. Most noises associated with a new fan will
disappear after this period.
1. If this is a downrod mount fan, make sure the ridge on mounting bracket engages the
notch in the downrod ball.
2. Make sure that canopy, mounting bracket or mounting plate are tightened securely to
4. Check that all blade holders are tightened securely to motor.
5. Most fan wobble problems are caused when blade levels are unequal. Check this level
by selecting a point on the ceiling above the tip of one of the blades. Measure this distance
from blade tip to ceiling. Keeping measure within 1/8", rotate the fan until the next blade
is positioned for measurement. Repeat for each blade. If all blade levels are not equal,
you can adjust blade levels by the following procedure. To adjust a blade tip down, insert
a washer (not supplied) between the blade and blade holder at the screw closest to the
motor. To adjust a blade tip up, insert washer (not supplied) between the blade and blade
holder at the two screws farthest from the motor. Reverse the position of the washer if
blades mount from top of blade.
6. If blade wobble is still noticeable, interchanging two adjacent blades can redistribute the
weight and possibly result in smoother operation.
If the above steps do not eliminate the wobble problem, you will need to dynamically
balance your fan with balancing kit provided.
1. Check blue wire from fan to make sure it is connected to hot wire from house.
2. Check for loose or disconnected wires in fan switch housing.
3. Check for loose or disconnected wires in light kit.
4. Check for faulty lightbulb and make sure bulb is tight in socket.
5. Remove light kit and check the plug connections if they are present.
6. If this fan uses a remote controller, make sure dip switches are in the correct setting
and make sure the battery works.
CAUTION: Make sure main power is turned off before entering switch housing and/or
canopy.
2. If fan sounds noisy:
3. If fan wobbles:
4. If light does not work:
1. If fan does not start:
Trouble Suggested Remedy

Nov.2022