Monte Carlo Fan Company 5CNR52 Instruction manual

Owner’s Guide and Installation Manual
Attach sales receipt to this card and retain as your proo o purchase
DATE OF PURCHASE:
MODEL NUMBER:
RETAILER NAME:
RETAILER ADDRESS:
To register your ixture, please visit our website www.montecarlo ans.com
5CNR52XXD-L Series Fan
Total an weight with light kit
UL Model No. : 5CNR52
11.5 kgs
25.3 lbs

© 2011 Monte Carlo Fan Company 1/16/2012
2
WARNING: T REDUCE THE RISK F FIRE, ELECTRIC SH CK, R INJURY T PERS NS, BSERVE THE F LL WING
READ AND SAVE THESE INSTRUCTI NS
Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA
70-1999), including fire-rated construction.
Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor
on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be
turned upward and pushed carefully up into the outlet box.
WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet
from the floor to the trailing edge of the blade.
WARNING: To Reduce The Risk f Fire, Electric Shock, or Personal Injury, Mount To utlet Box Marked “Acceptable for Fan Support of
15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The utlet Box.
CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Re-
move Knockouts In The utlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to
the building structure (or the ceiling joist).
WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do
not insert foreign object between rotating blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.
WARNING: To reduce the risk of fire or electric shock, this fan should only be used with fan speed control part no. UC7067RC manufac-
tured by Rhine Electronic Co., Ltd.
WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed
control.
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
Never place a switch where it can be reached from a tub or shower.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating
equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the
American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.
All set screws must be checked and tightened where necessary before installation.
Customer Service
800-969-3347
Customer Service Center
7400 Linder Ave.
Skokie, IL 60077
www.montecarlo ans.com
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,
Stepladder and Wire Strippers.

© 2011 Monte Carlo Fan Company 1/16/2012
3
Before you begin installing the fan, Switch
power off at Service panel and lock service dis-
connecting means to prevent power from being
switched on accidentally. When the service dis-
connecting means cannot be locked, securely
fasten a prominent warning device, such as a
tag, to the service panel.
Before installing this fan make sure the outlet box is
properly installed to the house structure. To reduce
the risk of fire, electric shock, or personal injury,
mount to outlet box or supporting system acceptable
for fan support. (Mounting must support at least 35
lbs.)
Use metal outlet box suitable for fan support
(must support 35 lbs). Before attaching fan to
outlet box, ensure the outlet box is securley fas-
tened by at least two points to a structural ceiling
member ( a loose box will cause the fan to wab-
ble). Use only the screws provided with the
outlet box.
lace canopy, canopy disk, yoke on down-
rod as in photo. Then thread leadwires
and safety cable through the downrod in
direction of arrow.
3
21
6
Remove keeper from pin. ut
keeper back in pin and save for
later.
4
Loosen the 2 set screws in yoke
for downrod to slip into yoke.
5
Insert downrod into yoke on top of the Fan
Body.
Align the hole in the Downrod with the hole in
the Yoke. Insert the in through the Yoke and
Downrod until the point appears on the other
side. Install the Keeper in
78
Yoke Cross in
Keeper
in
Tighten the 2 Set screws on the Yoke
once the downrod is in place.
9

© 2011 Monte Carlo Fan Company 1/16/2012
4
Hang assembled fan from the mounting bracket in-
stalled to ceiling in previous step. Make sure the fan
is hanging straight. Rotate fan until the tab on the
Mounting bracket engages the slot on the Downrod
Ball. This must be done to prevent the fan body from
rotating when the blades are in motion.
12
Make wire connections to power source using wire nuts
provided. Make sure that no filiments are outside of
the wirenut. After making the wire connections, the
wires should be spread apart with the grounded con-
ductor and the equipment-grounding conductor on one
side of the outlet box and ungrounded conductor on the
other side of the outlet box.
16
Make sure the studs protruding from the
bottom of the Mounting bracket are in-
stalled with threads all the way through
the bracket.
11
Lift Conopy allowing the 2 studs to
protrude through the canopy.
17
Next lift the cover ring and install knurled
nuts as shown. Tighten the knurled nuts
securely. The canopy should adjust for
any irregularity in the ceiling or Outlet
box.
18
Cover Ring
Slide remote receiver into mounting
bracket.
15
For Canadian installation and for USA fan and
light kit combinations over 35 lbs, in both flush
and downrod mode the safety cable must be in-
stalled into the house structure beams using the
3” lag screws,washers, and lock washers. pro-
vided. Make sure that when the safety cable is
fully extended the leadwires are longer than the
cable and no stress is placed on the leadwires.
Note:If Installing It In The U.S., Do Not Re-
move Knockouts In The Outlet Box
10 Safety cable installation
Safety Cable
Lag Screw
safety
cable
3” lag
screw
lock
washer
washer
Set dip switches on the Remote Transmitter and Remote
Receiver to the same settings. This must be done so the
units will communcate properly. If you have other fans
you can set to control from one transmitter by setting both
receivers the same as the transmitter. If you have more
than one fan with remote. You can set the dip switches to
different positiosns to have seperate control.
Remote Transmitter Dip swtiches
Remote Receiver Dip switches
14
Make wiring connections as indicated above.
White from fan to white from remote marked
N. Blue from fan to blue from remote marked
light. Black from fan to Black from remote
marked L. White from house to white from re-
mote marked AC N . Black from house to
Black from remote marked AC L. Connect all
green ground wires to Ground wire from
House.
13
white
black

© 2011 Monte Carlo Fan Company 1/16/2012
5
Install 3 screws and fiber washers to back side
of blade as shown.
27
Hang fan from mounting bracket by
the hands free “S” hook in hardware
pack into a closed hole on the edge of
the canopy and over bracket.. Note:
For Canadian mounting refer to Step
#10.
24
Remove side covers to canopy.
20
23
Remove the all thread studs from the
lower part of the mounting bracket. Install
2 screws that align with the “L” shape
holes in the canopy into the mounting
bracket. (see step 15)
Screw for “L”
shape slots
Screw for “L”
shape slots
“L” shape
slots
lace canopy on top of the fan motor allowing the
yoke to pass through the large hole in the center of
the canopy. Align the 3 larger holes around the
center hole with the 3 screws already installed in
the fan. Install 3 flush mount screws removed pre-
vious step into smaller holes and tighten securely.
22
Canopy
Center
Hole
Larger
holes
Smaller
holes
Lift fan to mounting bracket, aligning the “L”
shape holes with the scresws on the mount-
ing bracket. Turn the fan clockwise to lock
in position. Install the other two screws and
tighten securely.
25
Remove 2 screws in yoke. Remove 3
screws (every other screw) from top of
fan.
21
Swing blade holders out and align hole with
arrow on blade holder with hole in blade with
arrow. Make sure that the side of the blade
that has the sticker this side up is facing up-
ward.
26
ass leadwires and safety cable through
the canopy. Steps 19-25 for flush
mount installation skip to step 26 if
using the downrod.
19 Flush Mount Installation

© 2011 Monte Carlo Fan Company 1/16/2012
6
Attach glass by locating dimples in
light fixture with the groves in glass
and twisting clockwise till tight.
30
Tighen screws securely. Repeat this
process 4 more times until all blades are
assembled.
28
install 1 x 100 watt halogen bulb with socket
type E-11. Do not touch bulb surface as oily
residue from skin can cause the bulb to ex-
plode.
WA NING: Over lamping the fan will
result in the fan lights shutting down
until the proper wattage of bulbs are
installed. eset the lights by turning off
the wall switch, breaker,or by remote. e-
place bulbs with the correct wattage bulbs,
turn the power on.
29
Remove cover by snaping off from top or bot-
tom. Remove battery cover. Install 12V battery
into wall remote. Duracell MN21 / Eveready A23
/ G 23A all 12V.Attach cover of remote by plac-
ing over buttons and snap the battery cover in
place.
lace face plate over battery compartment and
buttons. lace remote over 2 pins on front
cover. Attach cover of remote by placing over 4
pins and snaping into place.
Install wall control unit to outlet box
using machine screws provided.
33
Attach front cover to wall control
with screws provided. Snap battery
cover in place.
34
32
31 HAND HELD INSTALL WALL MOUNT INSTALL

© 2011 Monte Carlo Fan Company 1/16/2012
7
emote Control Transmitter Fea-
tures:
FAN SPEED Depress “1 dot” for low speed, “2 dots” for medium or “3 dots” for
high. To turn fan off press square”.
LIGHT DIMME To turn light on, press light dimmer once quickly. To turn off
press once quickly while light is on. To dim light hold down button “light dimmer”.
The light will cycle from bright to dim to bright until button is released. Light will
maintain last setting if turned off.
FO WA D/ EVE SE Depress rev button allow a few seconds for remote to
change rotation direction with fan running.
HIGH S EED
MEDIUM S EED
LOW S EED
FAN OFF SETTING
(Turns fan off only)
FAN REVERSE
(ress once to
change direction of
the fan)Fan must
be running to re-
verse.
LIGHT ON/OFF SET-
TING AND DIMMER
( ress and hold to
dim light infinitively)
LED LIGHT

© 2011 Monte Carlo Fan Company 1/16/2012
8
Remove glass from light fixture by
twisting counter clockwise.
1
Remove halogen bulb. Do not touch
glass of bulb with your hands.
2
Remove light fixture by loosing 2
screws with key slots and remove 1
screw without key slot. Save screw.
3
Remove light fixture by twisting
counter clockwise.
4
Unplug light fixture wires from fan
wires.
5
Remove light plate by loosing 2
screws with key slots and remove 1
screw without key slot. Save screw.
6
Remove light plate by twisting
counter clockwise. Then remove the
light pan by removing the remaining
2 screws. Save screws.
7
Remove 2 screws per blade holder.
Remove blade holder. When replac-
ing blade holders make sure the
screws are tightened securely to
the motor.
89
BLADE HOLDER RE LACEMENT for 5CNR52XXD
Reverse steps 8 thru 1 to
replace blade arms and put
fan back together.
10
Trouble Shooting Blade Arms
If fan makes noise check to make sure the screws that attach blade holders to motor are tight.
If fan wobbles check that all blade holders are tighened securely to the motor.

© 2011 Monte Carlo Fan Company 1/16/2012
9
1.Check main and branch circuit fuses or circuit breakers.
2.Check line wire connections to fan and switch wire connections in switch housing.
CAUTION: Make sure main power is turned off.
3.Check to make sure the dip switches from the transmitter and receiver are set on the same
frequency.
4.Make sure that shipping stabilizer tabs have been removed from motor.
1.Check to make sure all screws in motor housing are snug (not over tightened).
2.Check to make sure the screws which attach the fan blade holder to the motor are tight.
3.Check to make sure wire nut connectors in switch housing are not rattling against each other or
against the interior wall of the switch housing.
CAUTION: Make sure main power is turned off before entering switch housing.
4.If using an optional Ceiling Fan Light Kit, check to be sure the screws securing the glassware
are finger tight. Check to be sure light bulb is tight in socket and not touching glass shade(s). If
vibration persists from glass, remove glass and install a 1/4" wide rubber band on glass neck to
act as an insulator. Replace glass and tighten screws against rubber band.
5.Some fan motors are sensitive to signals from Solid State variable speed controls. DO NOT
USE a Solid State variable speed control.
6.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear after
this period.
1.Make sure that the ridge of the canopy engages the notch in the downrod ball.
2.Check that all blades are screwed firmly into blade holders.
3.Check that all blade holders are tightened securely to motor.
4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box and
junction box is mounted firmly to ceiling joist.
5.Most fan wobble problems are caused when blade levels are unequal. Check this level by select-
ing a point on the ceiling above the tip of one of the blades. Measure this distance from blade tip
to ceilng. Keeping measure within 1/8", rotate the fan until the next blade is positioned for meas-
urement. Repeat for each blade. If all blade levels are not equal, you can adjust blade levels by
the following procedure. To adjust a blade tip down, insert a washer (not supplied) between the
blade and blade holder at the screw closest to the motor. To adjust a blade tip up, insert washer
(not supplied) between the blade and blade holder at the two screws farthest from the motor.
Reverse the position of the washer if blades mount from top of blade.
6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redis-
tribute the weight and possibly result in smoother operation.
1.Check blue wire from fan to make sure it is connected to hot wire from house.
2.Check for loose or disconnected wires in fan switch housing.
3.Check for loose or disconnected wires in light kit.
4.Check for faulty light bulbs.
WA NING: Over lamping the fan will result in the fan lights shutting down until
the proper wattage of bulbs are installed.
eset the lights by turning off the wall switch, breaker,or by remote. eplace bulbs
with the correct wattage bulbs, turn the power on.
CAUTION: Make sure main power is turned off before entering switch housing.
WA NING: Before attempting to replace the fuse make sure the main power is turned
off to the fan. (Fuse is inside the canopy on the blue wire to remote receiver, push and
twist the cap to open the fuse case) Push and twist to reassemble fuse.
isk of fire. eplace fuse only with 3 amp, 125 volt fuse.
2. If fan sounds noisy:
1. If fan does not
start:
3. If fan wobbles:
4. If light does not
work:
TROUBLE SHOOTING
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or
wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please
check this Trouble Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installation,
please call our Customer Service Center at the number printed on your parts list insert sheet.
Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service discon-
necting means to prevent power from being switched on accidentally. When the service disconnecting
means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service
panel.
Trouble Suggested emedy

Jan.2012 New format
May.2013 Update for CUL regulation