Monte Carlo Fan Company 5CY60XX Series Instruction manual

Owner’s Guide and Installation Manual
Attach sales receipt to this card and retain as your proof of purchase
DATE OF PURCHASE:
MODEL NUMBER:
RETAILER NAME:
RETAILER ADDRESS:
To re ister your fixture, please visit our website www.montecarlofans.com
5CY60XX Series Fan
Total fan wei ht
UL Model No. : AC-570F811
14.58 kgs
32.08 lbs

© 2011 Monte Carlo Fan Company 2/10/2012
2
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING
READ AND SAVE THESE INSTRUCTIONS
Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA
70-1999), including fire-rated construction.
Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor
on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be
turned upward and pushed carefully up into the outlet box.
WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
ake sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet
from the floor to the trailing edge of the blade.
WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, ount To Outlet Box arked “Acceptable for Fan Support of
15.9 kg (35 lbs) or less” And Use ounting Screws Provided With The Outlet Box.
CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Re-
move Knockouts In The Outlet Box. ount the secondary support safety cable through the reserved nail/screw hole on the outlet box to
the building structure (or the ceiling joist).
WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do
not insert foreign object between rotating blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.
WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed
control.
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
Never place a switch where it can be reached from a tub or shower.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating
equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the
American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.
All set screws must be checked and tightened where necessary before installation.
Note: Suitable for use in wet locations when installed in a GFCI protected branch circuit.
Note: Use only with light kits marked suitable for use in wet locations.
Customer Service
800-969-3347
Customer Service Center
7400 Linder Ave.
Skokie, IL 60077
www.montecarlofans.com
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,
Stepladder and Wire Strippers.

© 2011 Monte Carlo Fan Company 2/10/2012
3
Before you begin installing the fan, S witch
power off at Service panel and lock service dis -
connecting means to prevent power from being
switched on accidentally. When the service dis -
connecting means cannot be locked, securely
fasten a prominent warning device, such as a
tag, to the service panel.
Remove keeper from pin. Remove
pin, replace keeper and save.
1
4
Thread wire through downrod with
canopy and yoke cover assembled
onto downrod.
6
Before installing this fan make sure the outlet
box is properly installed to the house structure.
To reduce the risk of fire, electric shock, or per -
sonal injury, mount to outlet bo x or supporting
system acceptable for fan support.
(Mounting must support at least 35 lbs.)
Use metal outlet box suitable for fan support
(must support 35 lbs). Before attaching fan to
outlet box, ensure the outlet bo x is securely
fastened by at least two points to a structur al
ceiling member ( a loose bo x will cause the fan
to wobble). Use only the screws provided
with the outlet box.
3
2
Loosen the 2 set screws in y oke for
downrod to slip into yoke.
5
Insert downrod into motor yoke.
Next, insert clevis pin through y oke
and downrod.
79
Tighten both yoke set screws to fur-
ther secure downrod.
8
Secure with cotter pin.

© 2011 Monte Carlo Fan Company 2/10/2012
4
Carefully lift fan assembly onto mounting
bracket. Rotate fan so that the notch on the
ball engages the ridge in the mounting br acket.
This will allow hands-free wiring.
12
Install 3 screws and washers per
blade and tighten securely. Repeat
for all 5 blades. The blades will ha ve
a label showing this side up on each
blade.
18
Make wire connections to power source
using wire nuts provided. Make sure that
no filiments are outside of the wirenut.
After making the wire connections, the
wires should be spread apart with the
grounded conductor and the equipment -
grounding conductor on one side of the out -
let box and ungrounded conductor on the
other side of the outlet bo x.
14
For pullchain controls, follow diagram above.
Make sure that all exposed wiring is secured
inside wire nuts. Note: Wires from house ma y
vary in color and ma y not include ground wire.
After wiring is conplete, gently push wires into
junction box with wire nuts pointing upw ard.
Refer to point 3 of safet y tips.
15 House Fan
Black
White
Green
Black
White
Green(downrod)
Green(Bracket)
Blue
For control of fan and optional light from w all
location, follow diagram above. NOTE: A profes-
sional electrician is recommended for this t ype
of installation.
16
Light Switch
Fan Switch
Wall
Control
Remove screws from stabilizer plate
on bottom of fan motor.
10 11
Remove stabilizer plate you will not
need this plate.
Loosen one and remove one preassem-
bled screw from mounting bracket.
Save screw. Lift canopy up, aligning its
keyhole slot with the preassembled
screw on mounting bracket and twist
clockwise to lock in place. Re-install the
removed screw and tighten all screws
securely.
17
For Canadian installation and for USA fan and light
kit combinations over 35 lbs, in both flush and
downrod modes the safety cable must be installed
into the house structure beams using 3” lag
screws, washers and lock washers provided. Make
sure that when the safety cable is fully extended
the lead wires are longer than the cable and no
stress is placed on the lead wires.
Note:If Installing The Secondary Support Safety
Cable in the U.S., Do Not Remove Knockouts In
The Outlet Box.
1Safety cable installation
Safety Ca le
Lag Screw
safety
cable
3” lag
screw
lock
washer
washer

© 2011 Monte Carlo Fan Company 2/10/2012
5
Remove 4 screws and save to install
switch housing.
26
Install switch housing plate b y twist-
ing plate with key hole slots into
place. Replace screw removed and
tighten the 3 screws securely.
21
Connect plug from fan to switch
housing plug. Match the color strips
on the plugs.
22
Loosen 2 screws with key slots and
remove 1 screw without slot from
motor plate and save screw.
20
The screws, washers, and motor
pads are pre-installed to the blade
holders. Attach blade assembly to
motor and tighten screws securely.
19
Black capacitor box needs to be
stuck to the switch housing. Not
being attached can cause motor
noise.
Remove twin adhesive tape from the
black capacitor as shown above.
24
23
Place and press firmly on the capaci -
tor to stick it to the switch housing.
Be sure it is secure.
25
Install the switch housing using the 4
screws previously removed.
Setting the reverse switch in the
left hand side will result in down-
ward airflow and setting the
switch in the right hand side will
result in upward airflow.
27
Reverse
switch

© 2011 Monte Carlo Fan Company 2/10/2012
6
1.Check main and branch circuit fuses or circuit break ers.
2.Check line wire connections to fan and switch wire connections in switch housing.
3.Make sure that any shipping stabilizer has been removed from motor.
CAUTION: Make sure main power is turned off.
1.Check to make sure all screws in motor housing are snug (not o ver tightened).
2.Check to make sure the screws which attach the fan blade holder to the motor are tight.
3.Check to make sure wire nut connectors in switch housing are not r attling against each
other or against the interior w all of the switch housing.
CAUTION: Make sure main power is turned off before entering switch housing.
4.Some fan motors are sensitive to signals from Solid State v ariable speed controls. DO
NOT USE a Solid State variable speed control.
5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear
after this period.
1.Make sure that the ridge of the canop y engages the notch in the downrod ball.
2.Check that all blades are screwed firmly into blade holders.
3.Check that all blade holders are tightened securely to motor .
4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction bo x
and junction box is mounted firmly to ceiling joist.
5.Most fan wobble problems are caused when blade lev els are unequal. Check this lev el by
selecting a point on the ceiling abo ve the tip of one of the blades. Measure this distance
from blade tip to ceilng. K eeping measure within 1/8", rotate the fan until the next blade is
positioned for measurement. Repeat for each blade. If all blade lev els are not equal, y ou can
adjust blade levels by the following procedure. To adjust a blade tip down, insert a w asher
(not supplied) between the blade and blade holder at the screw closest to the motor . To
adjust a blade tip up, insert washer (not supplied) between the blade and blade holder at
the two screws farthest from the motor. Reverse the position of the w asher if blades mount
from top of blade.
6.If blade wobble is still noticeable, interchanging two adjacent (side b y side) blades can
redistribute the weight and possibly result in smoother oper ation.
1.Check wire from fan to mak e sure it is connected to hot wire from house.
2.Check for loose or disconnected wires in fan switch housing.
3.Check for loose or disconnected wires in light kit.
4.Check for faulty light bulbs.
CAUTION: Make sure main power is turned off before entering switch housing.
2. If fan sounds noisy:
1. If fan does not
start:
3. If fan wobbles:
4. If light does not
work:
Trouble Shooting
If you have difficulty operating your new ceiling fan, it ma y be the result of incorrect assembly, installation,
or wiring. In some cases, these installation errors ma y be mistaken for defects. If y ou experience any faults,
please check this Trouble Shooting Chart. If a problem cannot be remedied, or y ou are experiencing difficulty
in installation, please call our Customer Service Center at the number printed on y our parts list insert sheet.
Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service dis -
connecting means to prevent power from being switched on accidentally. When the service dis -
connecting means cannot be locked, securely fasten a prominent warning device, such as a tag,
to the service panel.
Trouble Suggested Remedy