Monte Carlo Fan Company 5SLR52 Series User manual

QUALITY CEILING FANS
OWNER’S
MANUAL
Ceiling Fan Installation Instructions
Total fan weight
with light
READ AND SAVE THESE INSTRUCTIONS
For 5SLR52 Series Fans

Remove keeper from pin and pin
from downrod. Place keeper back on
pin and save for later.
5
Loosen the 2 set screws till you can
not feel them on inside of yoke.
4
Thead leadwires and safety cable
through downrod. (as shown)
6
Before you begin installing the fan, Switch
power off at Service panel and lock service dis-
connecting means to prevent power from being
switched on accidentally. When the service dis-
connecting means cannot be locked, securely
fasten a prominent warning device, such as a
tag, to the service panel.
Before installing this fan make sure the outlet box is
properly installed to the house structure. To reduce
the risk of fire, electric shock, or personal injury,
mount to outlet box or supporting system acceptable
for fan support. (Mounting must support at least 35
lbs.)
Use metal outlet box suitable for fan support
(must support 35 lbs). Before attaching fan to
outlet box, ensure the outlet box is securley
fastened by at least two points to a structural
ceiling member ( a loose box will cause the fan
to wabble). Use only the screws provided
with the outlet box.
3
21
Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes ANSI/NFPA 70-1999),
including fire-rated construction.
Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding con-
ductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box.
Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from
being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device,
such as a tag, to the service panel.
Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7
feet from the floor to the trailing edge of the blade.
To reduce the risk of fire, electric shock, or personal injury, mount to outlet box or supporting system acceptable for fan support.
Use only the screws provided with the outlet box. (Mounting must support at least 35 lbs.)
Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating
blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
WARNING - To reduce the risk of fire or electric shock, this fan should be used with fan speed control part no. UC7067RC-L, manufac-
tured by Rhine Electronic Co., Ltd.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heat-
ing equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA),
and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such
as a tag, to the service panel.
WARNING - To reduce the risk of electric shock, this fan must be installed with an isolating wall contorl,switch.
WARNING - All set screws must be checked and retightened where necessary before installation.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS
SAFETY TIPS
TOOLS REQUIRED
Phillips Screwdriver Wire Cutters Pliers Step Ladder
Installation

Hang assembled fan from the mounting bracket
installed to ceiling in previous step. Make sure
the fan is hanging straight. Rotate fan until the
tab on the Mounting bracket engages the slot
on the Downrod Ball. This must be done to
prevent the fan body from rotating when the
blades are in motion.
14
Make sure the studs protruding from the
bottom of the Mounting bracket are
installed with threads all the way through
the bracket.
16
Place downrod into fan yoke.
9
Install the keeper to pin.
11
Tighten the 2 set screws on the yoke
once the downrod is in place.
12
Align the hole in the downrod with
the hole in the yoke. Insert th pin
through the yoke and downrod until
the point appears on the other side.
10
Thread leadwires and safety cable
through downrod. (as shown)
8
Place yoke cover on downrod. (as
shown)
7
Pull down yoke cover.
13
Install remote receiver into mounting
bracket.
18
Set dip switches on the Remote Transmitter and
Remote Receiver to the same settings. This must be
done so the units will communicate properly. If you
have other fans you can set to control from one trans-
mitter by setting both receivers the same as the
transmitter. If you have more than one fan with
remote. You can set the dip switches to different posi-
tions to have seperate control.
17
Remote Transmitter
Dip switches
Remote Receiver Dip
switches
Fan and light kit combinations over 35 lbs,
in both flush and downrod mode the safety
cable must be installed into the house struc-
ture beams using the 3” lag screws,washers,
and lock washers. provided. Make sure that
when the safety cable is fully extended the
lead wires are longer than the cable and no
stress is placed on the lead wires.
15 Safety cable installation
Safety Cable
Lag Screw
safety
cable
3” lag
screw
lock
washer
washer

Attach glass by locating dimples in
light kit with the groves in glass and
twist clockwise till tight.
30
Connect plug from fan to switch
house plug. (as shown)
26
Make wiring connections for remote
receiver to fan as above diagram.
21
Carefully snap flurescent lamp into
clips.
29
Attach blades to motor using screws
and washers in hardware bag and
tighten screws securely.
24
Loosen 2 screws and remove 1 screw
from motor plate. Save removed
screw for use later.
25
Install light plate with ballast to fan
by twisting plate with key hole slots
into place. Replace screw removed
and tighten the 3 screws securely.
27
Plug ballast into the flourescent
lamp.
28
Ready for wiring
19
Lift canopy and install knurled nuts as
shown. Tighten the knurled nuts securely.
The canopy should adjust for any irregu-
larity in the ceiling or Outlet box.
23
Make wire connections to power source using
wire nuts provided. Make sure that no filiments
are outside of the wirenut. After making the
wire connections, the wires should be spread
apart with the grounded conductor and the
equipment-grounding conductor on one side of
the outlet box and ungrounded conductor on
the other side of the outlet box.
22
Connect black from remote receiver to black or
(hot) wire from house. Connect white wire from
remote receiver to white (neutral) wire from
house. Connect green ground leads from
mounting bracket and downrod to ground lead
from house. Refer to Safety Tips section of
manual.
20

Attach front cover to wall control
with screws provided.
34
Install wall control unit to outlet box
using machine screws provided.
33
Remove cover by snapping off from top or
bottom. Install 12V battery into wall
remote. Duracell MN21 / Eveready A23 /
GP 23A.
31
Attach cover of remote by placing
over buttons and snapping into
place.
32
35
To control fan speed select from High,
Medium or Low speed buttons. To turn the
fan off press the fan on / off button. To
dim lights press and hold button. To turn
off light press and quickly release button.
Press button marked REV to reverse the
rotation direction of the fan blades with fan
on low or med.
Fan speed control
buttons
Fan on / off
Light dimmer for
lights
Fan reverse button

Customer Service Center:
740 S.W. Loop 820, Suite 110
Fort Worth, Texas 76115
1-800-519-4092
1.Check main and branch circuit fuses or circuit breakers.
2.Check line wire connections to fan and switch wire connections in switch housing.
CAUTION: Make sure main power is turned off.
3.Make sure forward/reverse switch is firmly in up or down position. Fan will not operate when
switch is in the middle.
1.Check to make sure all screws in motor housing are snug (not over tightened).
2.Check to make sure the screws which attach the fan blade holder to the motor are tight.
3.Check to make sure wire nut connectors in switch housing are not rattling against each other or
against the interior wall of the switch housing.
CAUTION: Make sure main power is turned off before entering switch housing.
4.If using an optional Ceiling Fan Light Kit, check to be sure the screws securing the glassware are
finger tight. Check to be sure light bulb is tight in socket and not touching glass shade(s). If vibra-
tion persists from glass, remove glass and install a 1/4" wide rubber band on glass neck to act as
an insulator. Replace glass and tighten screws against rubber band.
5.Some fan motors are sensitive to signals from Solid State variable speed controls. DO NOT USE
a Solid State variable speed control.
6.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear after
this period.
1.Make sure that the ridge of the canopy engages the notch in the downrod ball. (See illustration in
Step #6 of Downrod Mount installation).
2.Check that all blades are screwed firmly into blade holders.
3.Check that all blade holders are tightened securely to motor.
4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box and
junction box is mounted firmly to ceiling joist.
5.Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting
a point on the ceiling above the tip of one of the blades. Measure this distance from blade tip to
ceilng. Keeping measure within 1/8", rotate the fan until the next blade is positioned for measure-
ment. Repeat for each blade. If all blade levels are not equal, you can adjust blade levels by the fol-
lowing procedure. To adjust a blade tip down, insert a washer (not supplied) between the blade and
blade holder at the screw closest to the motor. To adjust a blade tip up, insert washer (not supplied)
between the blade and blade holder at the two screws farthest from the motor. Reverse the posi-
tion of the washer if blades mount from top of blade.
6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistrib-
ute the weight and possibly result in smoother operation.
1.Check blue wire from fan to make sure it is connected to hot wire from house.
2.Check for loose or disconnected wires in fan switch housing.
3.Check for loose or disconnected wires in light kit.
4.Check for faulty light bulbs.
CAUTION: Make sure main power is turned off before entering switch housing.
2. If fan sounds noisy:
1. If fan does not start:
3. If fan wobbles:
4. If light does not work:
TROUBLE SHOOTING
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In
some cases, these installation errors may be mistaken for defects. If you experience any faults, please check this Trouble
Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installation, please call our
Customer Service Center at the
number printed on your parts list insert sheet.
Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means cannot
be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.