Monte Carlo Fan Company TRAVERSE 5TV52 D-V1 Series Instruction manual

Owner’s Guide and Installation Manual
Attach sales receipt to this card and retain as your proo o purchase
DATE OF PURCHASE:
MODEL NUMBER:
RETAILER NAME:
RETAILER ADDRESS:
To register your ixture, please visit our website www.montecarlo ans.com
5TV52XXXD-V1 Series Fan
Total an weight with light kit
CUL Model No. : 5TV52XXXD-V1
10.6 kgs
23.4 lbs

© 2013 Monte Carlo Fan Company 6/15/2013
2
WAR I G: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR I JURY TO PERSO S, OBSERVE THE FOLLOWI G
READ A D SAVE THESE I STRUCTIO S
Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (A SI/ FPA 70-1999), including
fire-rated construction.
Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the
outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be turned upward and pushed carefully up
into the outlet box.
WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent
power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a
tag, to the service panel.
Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor to the
trailing edge of the blade.
WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of
15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.
CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do ot Re-
move Knockouts In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to
the building structure (or the ceiling joist).
WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign
object between rotating blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.
WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
ever place a switch where it can be reached from a tub or shower.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equipment manufac-
turer’s guideline safety standards such as those published by the ational Fire Protection Association ( FPA), and the American Society for Heating, Refrigera-
tion and Air Conditioning Engineers (ASHRAE) and the local code authorities.
CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.
All set screws must be checked and tightened where necessary before installation.
Customer Service
800-969-3347
Customer Service Center
7400 Linder Ave.
Skokie, IL 60077
www.montecarlo ans.com
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,
Stepladder and Wire Strippers.

© 2013 Monte Carlo Fan Company 6/15/2013
3
Before you begin installing the fan, witch power off
at ervice panel and lock service disconnecting
means to prevent power from being switched on ac-
cidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent warn-
ing device, such as a tag, to the service panel.
1
Before installing this fan make sure the outlet
box is properly installed to the house structure.
To reduce the risk of fire, electric shock, or per-
sonal injury, mount to outlet box or supporting
system acceptable for fan support.
(Mounting must support at least 35 lbs.)
2
Thread safety cable through center
hole of the mounting plate. Thread
your house wires through center hole
also.These will be needed for wiring
of the fan.
4
ecurely attached the mounting plate
to the outlet box using two screws
supplied by the outlet box. se
metal outlet box suitable for fan
support (must support 35 lbs).
6
Place the decorative ring on the
motor housing.
3
Make wire connections to power source using
wire nuts provided. Make sure that no filiments
are outside of the wirenut. After making the
wire connections, the wires should be spread
apart with the grounded conductor and the
equipment-grounding conductor on one side of
the outlet box and ungrounded conductor on the
other side of the outlet box.
9
Connect black and blue wire from fan to Black
or (Hot) wire from house. Connect White wire
from Fan to White (Neutral) wire from house.
Connect Ground leads from mounting bracket
and downrod to Ground lead from house.
Refer to Safety Tips section of manual.
8
Carefully lift the fan motor assembly
and engage the slot in the motor
housing with the hook on the mount-
ing plate so that the motor is se-
curely suspended.
7
For Canadian installation and for U A fan and
light kit combinations over 35 lbs, in both flush
and downrod mode the safety cable must be in-
stalled into the house structure beams using the
3” lag screws provided. Make sure that when
the safety cable is fully extended the leadwires
are longer than the cable and no stress is placed
on the leadwires. Note:If Installing The econd-
ary upport afety Cable in the U. ., Do Not Re-
move Knockouts In The Outlet Box.
5afety cable installation
Safety Cable
Lag Screw
Lag Screw
Safety Cable
Washer
Lock Washer

© 2013 Monte Carlo Fan Company 6/15/2013
4
Lift the motor housing up aligning the L
shape holes with the screws and
washers on the mounting plate. Turn the
housing clockwise to hold in position. In-
stall the other two screws and washers
previously removed securely.
11
Loosen the two screws and washers
across from each other on the ridge
of the mounting plate. Remove the
other two screws and lock washers.
ave for later use.
10
Lift the decorative ring up and twist
clockwise till tight.
12
Check the motor for shipping stabiliz-
ers and remove if present. Attach
blades using screws and washers in
hardware pak. Tighten screws se-
curely.
13
Loosen 2 screws and remove 1 screw
from motor plate. ave removed
screw for use later.
14
Connect plug from fan to switch
house plug.
16
Install by twisting clockwise, add 1
screw removed step 14 to switch
housing plate. Tighten the 3 screws
securely.
15
Connect white wire from fan to white
wire from light fixture. Then plug
blue wire from fan to black wire from
light fixture.
18
Loosen the pre installed screws of
switch housing plate.
17

© 2013 Monte Carlo Fan Company 6/15/2013
5
Install 3 screws to install light pan.
For fan with light kit go
to step 20-21 to
finish.
For fan without light kit
go to step 22.
Attach glass by locating dimples in
light fixture with the groves in glass
and twisting clockwise till tight.
21
Attach the non light cover by locating
dimples in the light fixture with the
grooves in the non light kit cover and
twist clockwise till tight. WARNING:
Make sure light bulb is not installed
when using this cover.
22
Install 2 x 9.3W medium base
dimmable LED bulbs. California Title 24
compliant bulbs included.
Caution: Approved for use with LED
light bulb only (Part No. 97502S). Do
not use incandescent light bulb.
Caution: Do not replace bulb until it
cools down.
20
19

© 2013 Monte Carlo Fan Company 6/15/2013
6
Trouble Shooting
,I\RXKDYHGLϒFXOW\RSHUDWLQJ\RXUQHZFHLOLQJIDQLWPD\EHWKHUHVXOWRILQFRUUHFWDVVHPEO\LQVWDOODWLRQ
RUZLULQJ,QVRPHFDVHVWKHVHLQVWDOODWLRQHUURUVPD\EHPLVWDNHQIRUGHIHFWV,I\RXH[SHULHQFHDQ\IDXOWV
SOHDVHFKHFNWKLV7URXEOH6KRRWLQJ&KDUW,IDSUREOHPFDQQRWEHUHPHGLHGRU\RXDUHH[SHULHQFLQJGLϒFXOW\LQ
LQVWDOODWLRQSOHDVHFDOORXU&XVWRPHU6HUYLFH&HQWHUDWWKH
QXPEHUSULQWHGRQ\RXUSDUWVOLVWLQVHUWVKHHW
Warning%HIRUHVHUYLFLQJRUFOHDQLQJXQLW6ZLWFKSRZHURϑDW6HUYLFHSDQHODQG ORFN VHUYLFH GLVFRQQHFWLQJ
PHDQVWRSUHYHQWSRZHUIURPEHLQJVZLWFKHGRQDFFLGHQWDOO\:KHQWKHVHUYLFHGLVFRQQHFWLQJPHDQVFDQQRWEH
ORFNHGVHFXUHO\IDVWHQDSURPLQHQWZDUQLQJGHYLFHVXFKDVDWDJWRWKHVHUYLFHSDQHO
&KHFNPDLQDQGEUDQFKFLUFXLWIXVHVRUFLUFXLWEUHDNHUV
&KHFNOLQHZLUHFRQQHFWLRQVWRIDQDQGVZLWFKZLUHFRQQHFWLRQVLQVZLWFKKRXVLQJ
CAUTION0DNHVXUHPDLQSRZHULVWXUQHGRϑ
,IWKLVIDQ XVHV PDQXDO IRUZDUGUHYHUVH VZLWFK PDNHVXUH WKH VZLWFK LV SXVKHG¿UPO\
HLWKHUZD\)DQZLOOQRWRSHUDWHZKHQVZLWFKLVLQWKHPLGGOH
,IWKLVIDQXVHVUHPRWHFRQWUROOHUPDNHVXUHGLSVZLWFKHVDUHVHWWLQJSURSHUO\DQGPDNH
VXUHEDWWHU\LVHϑHFWLYH
&KHFNWRPDNHVXUHDOOVFUHZVLQPRWRUKRXVLQJDUHVQXJQRWRYHUWLJKWHQHG
&KHFNWRPDNHVXUHWKHVFUHZVZKLFKDWWDFKWKHIDQEODGHKROGHUWRWKHPRWRUDUHWLJKW
&KHFNWRPDNHVXUHZLUHQXWFRQQHFWRUVLQVZLWFKKRXVLQJDUHQRWUDWWOLQJDJDLQVWHDFK
RWKHURUDJDLQVWWKHLQWHULRUZDOORIWKHVZLWFKKRXVLQJ
CAUTION0DNHVXUHPDLQSRZHULVWXUQHGRϑEHIRUHHQWHULQJVZLWFKKRXVLQJ
&KHFNWREHVXUHOLJKWEXOELVWLJKWLQVRFNHWDQGQRWWRXFKLQJWKHJODVVVKDGH
6RPHIDQPRWRUVDUHVHQVLWLYHWRVLJQDOVIURP6ROLG6WDWHYDULDEOHVSHHGFRQWUROV
$OORZEUHDNLQSHULRGRIKRXUV0RVWQRLVHVDVVRFLDWHGZLWKDQHZIDQZLOOGLVDSSHDU
DIWHUWKLVSHULRG
,IWKLV LVD GRZQURG PRXQWIDQ PDNHVXUH WKHULGJHRQ PRXQWLQJEUDFNHWHQJDJHV WKH
QRWFKLQWKHGRZQURGEDOO
0DNHVXUH WKDW FDQRS\ PRXQWLQJ EUDFNHWRU PRXQWLQJ SODWH DUH WLJKWHQHG VHFXUHO\WR
FHLOLQJMXQFWLRQER[DQGMXQFWLRQER[LVPRXQWHG¿UPO\WRFHLOLQJMRLVW
&KHFNWKDWDOOEODGHVDUHVFUHZHG¿UPO\LQWREODGHKROGHUV
&KHFNWKDWDOOEODGHKROGHUVDUHWLJKWHQHGVHFXUHO\WRPRWRU
0RVWIDQZREEOHSUREOHPVDUHFDXVHGZKHQEODGHOHYHOVDUHXQHTXDO&KHFNWKLVOHYHOE\
VHOHFWLQJD SRLQWRQ WKHFHLOLQJDERYHWKH WLSRI RQHRIWKH EODGHV0HDVXUH WKLVGLVWDQFH
IURPEODGHWLSWRFHLOQJ.HHSLQJPHDVXUHZLWKLQURWDWHWKHIDQXQWLOWKHQH[WEODGH
LVSRVLWLRQHG IRU PHDVXUHPHQW 5HSHDWIRU HDFK EODGH ,I DOO EODGH OHYHOVDUHQRWHTXDO
\RXFDQDGMXVWEODGHOHYHOVE\WKHIROORZLQJSURFHGXUH7RDGMXVWDEODGHWLSGRZQLQVHUW
DZDVKHU QRW VXSSOLHG EHWZHHQ WKH EODGH DQG EODGH KROGHUDWWKHVFUHZ FORVHVW WR WKH
PRWRU7RDGMXVWDEODGHWLSXSLQVHUWZDVKHUQRWVXSSOLHGEHWZHHQWKHEODGHDQGEODGH
KROGHUDW WKH WZR VFUHZV IDUWKHVWIURPWKH PRWRU 5HYHUVH WKH SRVLWLRQRIWKH ZDVKHU LI
EODGHVPRXQWIURPWRSRIEODGH
,IEODGHZREEOHLVVWLOOQRWLFHDEOH LQWHUFKDQJLQJWZRDGMDFHQW VLGHE\VLGH EODGHVFDQ
UHGLVWULEXWHWKHZHLJKWDQGSRVVLEO\UHVXOWLQVPRRWKHURSHUDWLRQ
,IWKHDERYHVWHSVGRQRWHOLPLQDWHWKHZREEOHSUREOHP\RXZLOOQHHGWRG\QDPLFEDODQFH
\RXUIDQZLWKEDODQFLQJNLWSURYLGHG
&KHFNEOXHZLUHIURPIDQWRPDNHVXUHLWLVFRQQHFWHGWRKRWZLUHIURPKRXVH
&KHFNIRUORRVHRUGLVFRQQHFWHGZLUHVLQIDQVZLWFKKRXVLQJ
&KHFNIRUORRVHRUGLVFRQQHFWHGZLUHVLQOLJKWNLW
&KHFNIRUIDXOW\OLJKWEXOEDQGPDNHVXUHEXOELVWLJKWLQVRFNHW
5HPRYHOLJKWNLWDQGFKHFNWKHSOXJFRQQHFWLRQVLIWKH\DUHSUHVHQW
,IWKLVIDQXVHVUHPRWHFRQWUROOHUPDNHVXUHGLSVZLWFKHVDUHVHWWLQJSURSHUO\DQGPDNH
VXUHEDWWHU\LVHϑHFWLYH
CAUTION0DNH VXUH PDLQ SRZHULVWXUQHGRII EHIRUH HQWHULQJ VZLWFK KRXVLQJ DQGRU
FDQRS\
,IIDQVRXQGVQRLV\
,IIDQZREEOHV
,IOLJKWGRHVQRWZRUN
,IIDQGRHVQRWVWDUW
Trouble Suggested Remedy

Feb.2019 5TV42XXD-V1