Monte Carlo Fan Company 5PAR52 Series User manual

Quality Ceiling fans
Owner’s
Manual
Ceiling Fan Installation Instructions
For 5PAR52 Series Fans
READ AND SAVE THESE INSTRUCTIONS
Total fan weight

1. Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70-1999),
including fire-rated construction.
2. Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
3. After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one
side of the outlet box and ungrounded conductor on the other side of the outlet box.
WARNING: Unplug or disconnect from the power supply before service.
4. Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on
accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
5. Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
6. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
7. Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 10 feet from the
floor to the trailing edge of the blade.
8. WARNING: To reduce the risk of fire, electric shock, or personal injury, mount only to outlet box marked acceptable for fan support. Use only the
screws provided with the outlet box. (Mounting must support at least 35 lbs. (16kg.)).
9. WARNING: Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating
blades.
10. Attach the mounting bracket using only the hardware supplied with the outlet box
11. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
12. NEVER place a switch where it can be reached from a tub or shower.
13. The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equipment
manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for
Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
14. WARNING: Before attempting to replace the fuse make sure that the power is turned off to the fan. Replace only with 3 amp fuse.
15. Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on
accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
16. Suitable for use with solid-state speed control.
17. All set screws must be checked and retightened where necessary before installation.
Installation
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS
SAFETY TIPS
TOOLS REQUIRED
Phillips Screwdriver Wire Cutters Pliers Step Ladder
Before you begin installing the fan, Switch power off
at Service panel and lock service disconnecting means
to prevent power from being switched on accidentally.
When the service disconnecting means cannot be
locked, securely fasten a prominent warning device,
such as a tag, to the service panel.
Before installing this fan make sure the outlet
box is properly installed to the house structure.
WARNING: To reduce the risk of fire, electric
shock, or personal injury, mount to outlet box
or supporting system acceptable for fan sup-
port. (Mounting must support at least 35 lbs.(16
kg.)).
Install the Mountiing Bracket to the Outlet box.
To Reduce the Risk of injury use only the
screws provided with the outlet box.
Install 4 x15 watt candelabra base bulbs includ-
ed.
3
2
1
4
Loosen 2 screws and remove pin with keeper
for downrod, yoke cover and canopy to fit in
yoke of fan.
6
Install canopy onto downrod(see inset). Thread
black wire, white wire, and safety cable through
downrod
5

install cotter pin into cross pin.
Install downrod into yoke.
Raise fan with downrod assembled to the ceil-
ing bracket and hang fan assembly. Be sure to
rotate the downrod ball so that the notch in the
bracket engages the slot in the ball.
9
12
7
For Canadian installation in both flush and
downrod mode the safety cable must be
installed into the house structure beams using
the 3” lag screws provided. Make sure that
when the safety cable is fully extended the
leadwires are longer than the cable and no
stress is placed on the leadwires.
13 Canadian mounting only
Safety Cable
Lag Screw
Make wire connections to power source using
wire nuts provided. Make sure that no filiments
are outside of the wirenut. After making the
wire connections, the wires should be spread
apart with the grounded conductor and the
equipment-grounding conductor on one side of
the outlet box and ungrounded conductor on
the other side of the outlet box.
15
Attach blade brackets to blades using the blade
bracket screws and washers provided.
17
Check the motor for plastic shipping stabilizer
tabs, and remove them if they are present. The
screws, washers and motor pads are pre-
installed to the blade holders. Attach blade
assembly to motor and tighten screws securely.
18
Make wire connections as per above diagram.
Connect the white wire from the fan to the
White or Neutral wire from the power source.
Connect the black wire from the fan to the
Black or hot wire from the power source.
Connect all Green / Yellow wires from the fan,
Downrod and mounting bracket to the
Grounding wire from the house.After wire nuts
are installed push connections carefully into
outlet box with wire nuts pointing upward.
14
Set dip switches on the Remote Transmitter and Remote
Receiver to the same settings. This must be done so the
units will communcate properly. If you have other fans you
can set to control from one transmitter by setting both
receivers the same as the transmitter. If you have more
than one fan with remote. You can set the dip switches to
different positiosns to have seperate control.
Remote Transmitter Dip swtiches
Remote Receiver Dip switches
11
Lift Canopy to ceiling aligning the key hole slots
with the screws on the bottom of the Mounting
bracket. Rotate the canopy Counter Clockwise
to lock in place. Tighten the screws to secure
the Canopy. See inset for Keyhole shape
16
Align hole in downrod with hole in yoke and
install cross pin.
8
Tighten 2 downrod set screws.
10

Install wall control unit to outlet box
using machine screws provided.
22
Attach front cover to wall control
with screws provided.
23
Remove cover by snaping off from
top or bottom. Install 12V battery
into wall remote. Duracell MN21 /
Eveready A23 / GP 23A all 12V.
20
Attach cover of remote by placing
over buttons and snaping into place.
21
Tighen 3 switch cap housing screws
to secure switch cap housing to fan.
19
To control fan speed select from High, Medium
or low speed buttons. To turn the fan off press
the Fan on / off button. To dim upper lights
press and hold U/L botton. To dim Lower lights
press and hold D/L button. To turn off either
up or down light press and quickly release
either U/L or D/L button. Press button marked
REV to reverse the rotation direction of the fan
blades
Fan speed
control but-
tons
Fan on / off
Light dim-
mer for up
and down
lights
Fan
reverse
button
24

1.Check main and branch circuit fuses or circuit breakers.
2.Check line wire connections to fan and switch wire connections in switch housing.
3.Check to make sure the dip switches from the transmitter and receiver are set on the
same frequency.
CAUTION: Make sure main power is turned off.
1.Check to make sure all screws in motor housing are snug (not over tightened).
2.Check to make sure the screws which attach the fan blade holder to the motor are
tight.
3.Check to make sure wire nut connectors in switch housing are not rattling against
each other or against the interior wall of the switch housing.
CAUTION: Make sure main power is turned off before entering switch housing.
4.Some fan motors are sensitive to signals from Solid State variable speed controls.
5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disap-
pear after this period.
1.Make sure that the ridge of the canopy engages the notch in the downrod ball.
2.Check that all blades are screwed firmly into blade holders.
3.Check that all blade holders are tightened securely to motor.
4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction
box and junction box is mounted firmly to ceiling joist.
5.Most fan wobble problems are caused when blade levels are unequal. Check this level
by selecting a point on the ceiling above the tip of one of the blades. Measure this dis-
tance from blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the
next blade is positioned for measurement. Repeat for each blade. If all blade levels are
not equal, you can adjust blade levels by the following procedure. To adjust a blade tip
down, insert a washer (not supplied) between the blade and blade holder at the screw
closest to the motor. To adjust a blade tip up, insert washer (not supplied) between the
blade and blade holder at the two screws farthest from the motor. Reverse the position
of the washer if blades mount from top of blade.
6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades
can redistribute the weight and possibly result in smoother operation.
1.Check wire from fan to make sure it is connected to hot wire from house.
2.Check for loose or disconnected wires in fan switch housing.
3.Check for loose or disconnected wires in light kit.
4.Check for faulty light bulbs.
CAUTION: Make sure main power is turned off before entering switch housing.
Warning: Before attempting to replace the fuse make sure the power is turned
off to the fan. Replace only with 3 amp fuse.
2. If fan sounds noisy:
1. If fan does not start:
3. If fan wobbles:
4. If light does not work:
Trouble Shooting
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation,
or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults,
please check this Trouble Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty
in installation, please call our Customer Service Center at the number printed on your parts list insert sheet.
Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service dis-
connecting means to prevent power from being switched on accidentally. When the service dis-
connecting means cannot be locked, securely fasten a prominent warning device, such as a tag,
to the service panel.
Customer Service Center:
740 S.W. Loop 820, Suite 110
Fort Worth, Texas 76115
1-800-519-4092