Morphy Richards Max User manual

www.morphyrichards.co.uk
www.morphyrichardsindia.com
Getting the best from your
new juice extractor...
Please read and keep these instructions
Juice extractor
ax
INCH
ax
Juice extractor

juicer is firmly locked in position.
Important Safe guards
lBefore using the Liquidising / Grinder jar,
IN THE INTEREST OF YOUR SAFETY PLEASE ensure that the jar is properly assembled.
READ THE FOLLOWING INSTRUCTIONS Hold the jar in one hand and check if the
CAREFULLY, BEFORE USING THIS JUICE blades move freely and rotate.
EXTRACTOR
lFix the jar to the coupler by turning it
lPlace the Juice extractor on an even clockwise. Make sure it is firmly locked in
platform at a convenient height so that the position prior to usage.
ingredients under operation can be easily
lNever insert your hand or spatula or spoon
seen.
in the jar, when the Juice extractor is in
lHave sufficient space around the Juice operation.
extractor to keep the various items
lStop the Juice extractor at regular intervals
required. Also ensure that the Juice
and push the contents to the center of the
extractor is placed 6 inches away from the
jar, with the help of the spatula. If the motor
wall.
stalls, switch off the power supply
lKeep the Juice extractor away from heat immediately. This could be due to
and sunlight. overloading. The over load Protector (OLP)
lThe Juice extractor operates at optimum has been provided to trip the motor when
efficiency at the specified voltage. Wide overloaded. In case of tripping, follow the
variation in voltage may affect the instruction given on page No.4.
performance of the Juice extractor. lSince the blades are quite sharp, be careful
lThe motor is rated for 10minutes while removing them.
continuous operation. Do not use it for more lNever use hot water to clean the Juice
than the specified time. extractor
lClean oil traces inside the jar before first
use. NOTES :
lDo not run the Juice extractor without load. lParts illustrated in this use and care manual
are indicative only, parts provided with the
lChop the ingredient small enough to fit products may differ with illustrations.
through the opening, for juicing operation.
lEnsure that the juicer housing is fitted lThis Juice extractor is intended for
properly on to the motor housing before household use only.
operation.
lSpecifications are subject to change
lFor juicing operation, never switch on the
without notice.
Juice extractor unless the top cover of the
2

How to use the juicer
down slightly so that it fits
Place juicer housing on and locked properly on
the motor housing. Place the coupler of the motor
spout cover in position. housing. Rotate the mesh
(Fig. 5) a little to see that it fits
properly. (Fig. 6)
Place juicer mesh into the
housing and push it
3
INCH
5
4
8
1
6
7
2
3
Parts description
Motor housing Speed switches
Juicer housing Plunger
Spout cover Feeder
Top cover Juicer mesh
Clamp
1
2
3
4
5
6
7
8
9
(Fig 1)
ax
Know your juice extractor
9
Juice extractor
INCH
Fig. 6
ax
Juice extractor
Fig. 5
INCH
Juice extractor
a
x

Place top cover into Juicer The motor of the Juice extractor is protected by
housing and lock side a resetting type Over Load Protector (OLP).
clamps (Fig. 7) In case of overloading, the OLP disconnects
Wash and cut fruits / the power supply to the motor, In such an
ingredients to fit in feeder eventuality, switch off the supply. Remove the
opening. excess the load or add water to the ingredients,
if the recipe so
Plug in Push the switch permits. Wait for
button ( ). Push a few minutes.
ingredients into the feeder Reset the OLP
with the help of the plunger located below
(Fig. 8) the base plate
At the end of the operation, switch off the Juice and restart the
extractorand unplug. mixer. (Fig. 4)
Caution : Care & Cleaning
Do not use fruits such as Bananas & Peaches Cleaning of Juicer :
which produce a thick paste that can clog the
filter mesh. lTo clean Juicer mesh, hold it below running
tap water.
Remove pump from the
pulp container whenever lMove brush up & down across the juicer
it is full. Stop machine mesh.
before removing pulp lDo not wash the base unit or immerse it in
container. (Fig. 9) water as it could cause electrical hazards.
Wipe the base unit clean with a damp cloth
Motor over load protection to remove stains, if any and then Wipe with
a dry cloth to keep the base unit dry and
The Juice extractor is fitted with a heavy duty
clean.
universal motor using a winding wire that can
withstand extremes of temperatures.
Therefore, the chances of motor failure are
extremely rare.
It is however possible that the mixer motor may
get overloaded when you attempt to grind
quantities in excess.
Technical Data
Power Supply : AC 230V 50Hz
Wattage : 450W
INCH
Juice extractor
a
x
Fig. 8
INCH
Juice extractor
a
x
Fig. 9
S
E
R
P
S
T
O
R
E
S
T
E
SS
EE
RR
PP
SS
TT
OO
RR
EE
SS
TT
EE
Fig. 4
INCH
Fig. 7
Juice extractor
a
x
Morphy Richards products are intended
for household use only
Morphy Richards has a policy of
continuous improvement in product quality
and design. The Company, therefore,
reserves the right to change the
specification of its models at any time.
Products & parts are indicative only, the
actual product may differ.
Morphy Richards Ltd, Mexborough,
South Yorkshire, England, S64 8AJ