morse 85A-SS User manual

The Specialist In Drum Handling Equipment
Model 85A-SS
Drum Karrier
CONTENTS
Page
Receiving Procedures. . . . . . . . . . . . . . . . . . . . 1
Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Information. . . . . . . . . . . . . . . . . . . . . 1 - 2
Machine Description. . . . . . . . . . . . . . . . . . . 3
Operating Instructions. . . . . . . . . . . . . . .. . . . . 3
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . 3
Parts List and Diagram. . . . . . . . . . . . . . . . . . . 4
Operator’s Manual
for Morse Drum Karrier
made of Type 304 Stainless Steel
Model 85A-SS
Serial number 0404 to 0405 (MMYY)
Copyright 2005 - Morse Mfg. Co., Inc. Form PL85A-SS (0404-0405) (Updated 20 Aug, 2018 11:40 AM) 1
Receiving Procedures
Every Morse drum handler is inspected prior to shipping. However,
damage may be incurred during transit.
Check for visible damage. If you choose to accept damaged•
freight, always sign noting the damage on the Bill of
Lading.
Document the damage and have the truck driver sign. We•
recommend keeping a digital camera at your receiving dock
for this purpose.
Open packages expeditiously to check the condition of the•
goods. There is only a 24 hour window to notify the carrier
of any concealed damage.
Immediately• report all damage to the shipping company!
Then you may contact Morse for assistance with your
freight claim.
Morse Manufacturing will not be held responsible for any•
damaged freight that is not signed for as damaged.
Limited 2 Year Warranty
Morse drum handling equipment is guaranteed against defects in
workmanship or materials for two years when used properly within
its rated capacity. Warranty does not cover wear from normal use
or damage from accident or abuse. Motors and other purchased
parts carry the warranties of their manufacturers.
For warranty claims, contact your Morse Dealer to obtain a
return authorization number, and for return freight advice. Return
freight must be prepaid.
In all instances, liability is limited to the purchase price paid or to
repairing or replacing the product. Customer assumes liability for
anymodications,unauthorizedrepairsorpartssubstitution.
Safety Information
While Morse Manufacturing Co. drum handling equipment is
engineeredforsafetyandefciency,ahighdegreeofresponsibility
must be placed upon the machine operator to follow safe practices,
based primarily on common sense, upon which true safety
depends.
Failure to follow the safety precautions in this manual can result in
personal injury or property damage. Observe the same precautions
as with similar machinery where carelessness in operating or
maintenance is hazardous to personnel. Carefully read the safety
precautions below and throughout this manual.
Review the Material Safety Data Sheet(s) for the material(s) in
the drum(s) and take all necessary precautions. Safety shoes,
work gloves, hard hat and other personal protective devices are
recommended.
Prior to initial use, inspect all moving parts. Perform necessary
load test, inspections, operator training, etc.
[email protected] 727 West Manlius St.
East Syracuse, NY, 13057 USA
morsedrum.com [phone]

The Specialist In Drum Handling Equipment
Model 85A-SS
Drum Karrier
Operator’s Manual for Morse Model 85A-SS Drum Karrier made of Type 304 Stainless Steel
Serial number 0404 to 0405 (MMYY)
morsedrum.com
Copyright 2005 - Morse Mfg. Co., Inc. Form PL85A-SS (0404-0405) (Updated 20 Aug, 2018 11:40 AM) 2
Safety Information (continued)
DANGER - Indicates a situation which, if not avoided, will result in serious injury or death.
This signal word is limited to the most extreme situations.
WARNING - Indicates a situation which, if not avoided, could result in serious injury or
death.
CAUTION - Indicates a situation which, if not avoided, can result in damage to the machine.
WARNING - Drum Karriers are designed to handle one drum of the types listed at the top of page 3.
Machine Description. DO NOT attempt to handle any other type of drum or object.
WARNING - DO NOT exceed the weight capacity of 800 Lb.
WARNING - DO NOT operate damaged or malfunctioning unit, or a unit with missing parts.
WARNING - DO NOT lift people or suspend loads over people. Stay clear of suspended loads.
WARNING - DO NOT lift loads higher than necessary.
WARNING - DO NOT leave suspended loads unattended.
WARNING - DO NOT remove or obscure warning labels.
WARNING -DONOToperatewithoutrsthavingreadandunderstoodoperatingmanual.
WARNING - DO NOT make alterations or modify the unit. Under no circumstances should any
modicationsbemadetotheMorsemachinerywithoutfactoryauthorization.Anymodicationsmay
voidthewarranty.Thismachinewasdesignedtoperformaspecicjobandalterationsmayresultin
injury to operator or machine.
WARNING - Wear safety shoes with non-slip soles and hard toe protection.
CAUTION: DONOTallowdrumtoimpactonoor,ground,etc.
WARNING: This product can expose you to chemicals including cobalt, titanium dioxide, and 2-methylimidazole,
which are known to the State of California to cause cancer, and bisphenol-A, which is known to the State of
California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

The Specialist In Drum Handling Equipment
Model 85A-SS
Drum Karrier
Operator’s Manual for Morse Model 85A-SS Drum Karrier made of Type 304 Stainless Steel
Serial number 0404 to 0405 (MMYY)
morsedrum.com
Copyright 2005 - Morse Mfg. Co., Inc. Form PL85A-SS (0404-0405) (Updated 20 Aug, 2018 11:40 AM) 3
Machine Description
Model 85A-SS Drum Karrier is designed to lift, transport and
dispense a standard 55-gallon steel drum 22.5” in diameter. The
maximum capacity is 800 Lb.
Important
Review the Material Safety Data Sheet(s) for the material(s) in1.
the drum(s) and take all necessary precautions. Safety shoes,
work gloves, hard hat and other personal protective devices are
recommended.
Please read all instructions thoroughly before attempting to2.
operate your new Morse drum handler.
The 85 Series Drum Karriers have a maximum capacity rating of 800 Lb. for a FULL drum and 500 Lb. for a HALF-FULL drum, and3.
are designed to lift and move a drum of the size and type noted above. DO NOT exceed this rating. Exceeding this rating or handling
drums other than those mentioned above is unsafe and could result in equipment damage, excessive wear, awkward or dangerous
handling.
When loading, unloading, operating, or maintaining your MORSE drum handler, always use care and good judgment. Maintain secure4.
footingandarmhold.Keephandsandlooseclothingawayfromallmovingparts.Neverallowanyonetobebelowanypartofaraised
drum handler or drum. Read operating instructions and review the pictures in the sales brochure before operation.
The 85 Series are a “Group 1 structural and mechanical” below-the-hook lifting device which are covered by the American National5.
Standard ASME B30.20. The user should comply with all aspects of this standard.
Operating Instructions
StartwithDrum-Karrierontheoor.LowerhoistandengagehoisthooktoliftDrum-Karrier.1.
RaisehoisttoliftDrum-Karrierclearofoorandtransportittothedrum.2.
Suspend Drum-Karrier at a height which aligns drum saddle with center of drum.3.
With binder chain (item 10) hanging freely, push Drum-Karrier against drum so that saddle will encircle drum.4.
Secure the drum: drape the binder chain (item 10) across the face of the drum and engage a link in notch in hub of ratchet (item 12).5.
Pull up on ratchet handle to tighten chain. If the chain doesn’t cinch tightly on the drum, lift the pawl (item13) to loosen and release the
chainandtryagainwithadifferentlinkinthenotch.Firmhandpressureontheratchethandleshouldtightenthechainsufcientlyto
hold the drum. DO NOT use mechanical aids such as a pipe to extend handle for extra leverage.
Either one of the two spring loaded plunger tilt-locks may be locked to hold the drum upright. It is not necessary to lock both of them.6.
Raise hoist and position drum at pouring station.7.
Before unlocking the tilt-lock(s) to permit tilting the drum, it is recommended that you steady the drum and be prepared for its possible8.
tendency to tilt toward its heavier side.
With tilt-locks unlocked, manually tilt the drum for pouring. The drum pouring angle may be varied or it can be locked in horizontal9.
position by one of the tilt-locks.
After emptying, rotate drum back to vertical position and lower hoist to return the empty drum.10.
To remove drum: Pull ratchet handle to relieve pressure on ratchet teeth. Lift pawl handle (item 13) to release teeth engagement and11.
rotate ratchet to loosen chain and allow its removal from notch.
Maintenance
Lubricate ratchet, pawl, tilt locks, fulcrum shafts and other moving parts periodically to maintain free action and reduce wear.1.
Periodically inspect all moving parts, framework and contact areas for signs of wear, fatigue or loosening. Tighten, adjust or replace2.
parts as necessary to prevent failure and maintain proper function.

The Specialist In Drum Handling Equipment
Model 85A-SS
Drum Karrier
Operator’s Manual for Morse Model 85A-SS Drum Karrier made of Type 304 Stainless Steel
Serial number 0404 to 0405 (MMYY)
morsedrum.com
Copyright 2005 - Morse Mfg. Co., Inc. Form PL85A-SS (0404-0405) (Updated 20 Aug, 2018 11:40 AM) 4
ITEM QTY. PART # DESCRIPTION
1 3 64SS-P ROLL PIN, 3/16 X 1-1/4, SS
2 2 55SS-P WASHER, 3/4 SAE FL 1-1/2 OD SS
3 2 61SS-P ROLL PIN, 3/16 X 2-1/2 SS
4 2 60SS-P SPRING, PLUNGER, SS
5 2 59SS-P PLUNGER, 85-SS
6 1 3981SS-P NUT, 3/8-16 NYLON LOCK, SS
7 1 82SS-P HHCS, 3/8-16 X 2-1/4, SS
9 1 101ASS-P SADDLE ASM, 85A-SS
10 * 1 1287-P ** CHAIN, CINCH, 3/16 SS 33 LK
12 1 165SS-P RATCHET, STEEL-IT
13 1 168SS-P PAWL, STEEL-IT
14 1 136-P GRIP, HANDLE 7/8” X 4-3/4”
15 1 169SS-P SPRING, PAWL, SS
17 1 170SS-P 3/8” DIA X 5/8” SHOULDER, SS
21* 1 165KITSS-P KIT, RATCHET TIGHTENER, SS
22 1 2389SS-P OVERHEAD ASM, 85-SS
* Recommended spare parts
** Discontinued and no longer available. Replace with Part # 165KITSS-P (KIT, RATCHET TIGHTENER, SS).
Note: “SADDLE ASM” (drum holder assembly) includes the drum band and appropriate attached moving parts,
such as 6, 7, 10 & 21.