Motorline professional MPIE10 User instructions

Automatic Bollard
English
Please read the manual very
carefully before installation
AUTOMATIC BOLLARD
ASSEMBLY AND OPERATING MANUAL
MPIE10
400/600/800
V 2.1
R 03/2018

Page 01
Assembly manual of MPIE10 400/600/800
1) CAUTION: It is important to your safety that these instructions are followed. The
installation or misuse of this product may cause personal injuries or material damages.
A) Warning to the user and/or installer
Automatic Bollard
English
CONFORMITY:
Electrocelos S.A. declares, the automatic bollard MPIE10 follows the european
norms and directives:
2006/95/CE-Low voltage electrical equipment;
89/336/CEE-Electromagnetic compatibility.
EN 60335-1, EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3
Electrocelos S.A. declares, the control board follows the directive 95/05/EC (R&TTE)
2) Keep these instructions in a safe place for future reference.
3) This product was designed and produced stricly for the use indicated in this manual.
Any other use other than the ones expressly indicated may damage the product and/or
be a source of danger, invalidating the warranty.
4) Electrocelos S.A. is not liable for the incorrect use of this product, or another use
other than the one for which it was designed.
5) Electrocelos S.A. is not liable if the safety standards were not taken into account
when installing the equipment to be automated, or for any deformation that may occur to it.
6) Before the installation, turn off the power supply.
7) Electrocelos S.A. is not liable for the safety and proper installation of the product
when are used components that are not sold by itself.
8) Do not make any changes to the motor components and/or accessories.
9) The installer should inform the customer how to operate the product in emergencies
and provide him with a manual of use.
10) Keep the remote control out of reach of children, preventing the bollard to opperate
accidentally.
11) The custommer shall not, in any circunstances, attempt to repair or tune the
bollard. For this purpose, he must call a qualified technician.
12) Connect the bollard to a 230V power supply, with ground wire.
13) The equipment is determined for outdoor use.

Page 02
Model
Input
Power
Intensity
Thermical Protection
Temperature
WING400/600/800
24 VDC
60 W
1.2 - 4A
120ºC
>-20ºC; <+50ºC
Assembly manual of MPIE10 400/600/800
B) Technical Specifications
1) Motor Specifications:
Automatic Bollard
English
PVC 10 mm
Mobile piece
Covers Anti-Slip Stainless Steel 4mm
Fitted material
INOX 2.5 mm
400 mm
Diameter
Course 370 / 570 / 785 mm
Top flange
204 mm
Fitted material
Weight capacity when closed
320 x 320 x 870/ 320 x 320 x 1080 / 320 x 320 x 1280 (mm)
20.000 Kg
Weight 35 /40 /45 Kg
2) Mechanical Specifications:
3) Physical Specifications:

Page 03
Assembly manual of MPIE10 400/600/800
Solid base (in cement) to
support MPIE10
CAUTION:
1. IMPORTANT! Place the sewer with a minimum declination of 10º.
2. Put sand around the bollard, for better accommodation.
3. The cement must be made with sand.
4. The control box must be installed in a place near the bollard, at a minimum height of 20cm
from the ground.
5. If the distance from the control box to the bollard MP400/600/800 is bigger than 10 meters,
use a 2.25mm power cable.
Protective conduit
for cable passage
PVC cylinder
Power cable
Earth
Cover
Cement
Sewer
Sand
B
B
C
C
A
A
C) Underground Bollard Installation
Automatic Bollard
English
Figure 1: Bollard scheme
50mm
150mm
10º

Page 04
Don’t touch the screws marked at green - Fig.2
Important
Assembly manual of MPIE10 400/600/800
In order to install the bollard, you can dismount the cover, making the process much easier. To do
that, you must remove the 6 screws furthest from the center, marked at red in Fig.2.
Next, remove the cover as shown in Fig.3 and place the bollard in the hole (Fig. 5).
Note that no waste or other objects fall into the inside of the bollard protecting the space using a
piece of cloth, paper or other material serving as a seal between the stainless steel tube and the
PVC pipe (Fig.6) . After placing the bollard in the hole and finishing the pavement around it,
remove the material used for sealing and place the cover (Fig.3) in the bollard, fixing it with the six
screws removed early in the process.
The bollard and it’s cover must be aligned as shown in Fig.4.
The installation can be made without following these steps, however, it becomes more complex
and harder, so, it’s advised to follow the steps described above.
Figure 4: Bollard’s alignment
Figure 5: Bollard installed Figure 6: Seal the bollard
Figure 2: Cover Figure 3: Removing Cover
C) Underground Bollard Installation
Automatic Bollard
English

Page 05
250mm
MPI10/ 400: 920mm MPI10/ 600: 1130mm MPI10/ 800: 1330mm
MPI10/ 400: 370mm MPI10/ 600: 570mm MPI10/ 800: 785mm
MPI10/ 400: 870mm MPI10/ 600: 1080mm MPI10/ 800: 1280mm
Assembly manual of MPIE10 400/600/800
D) Dimensions
Automatic Bollard
English

Automatic Bollard
English
Page 06
E) Electrónica y control:E) Electrónica e controle:
Assembly manual of MPIE10 400/600/800
E) Unlocking
Slot to make the release
- After unlocking, the MPIE10 400/600/800 will descend automatically.
- In case of power outage, the bollard is prevented by a battery that has enough power to
make one maneuvre (open or close). You shall not use the bollard anymore untill there is a
power supply at 230V because the battery was designed for emergencies only.
In case you use the bollard more than 1 time powered only by the battery, it may not have
enough energy and an incomplete maneuvre may occur.
- In case of malfuncion of the equipment, you shall call a qualified technician.
Rotate the key in clockwise direction
IMPORTANT
Unlocking the bollard in case of an emergency, power outage or
malfunction.

Automatic Bollard
English
Page 07
Assembly manual of MPIE10 400/600/800
IMPORTANT
ATTENTION!
A protective conduit must be used
for underground cable passage.
This cable can’t be buried in
direct contact with the soil.