Motorline professional ECO PLUS RAPID DOOR Use and care manual

v1.1
REV. 06/2018
EN
USER’S AND INSTALLER’S MANUAL
ECO PLUS RAPID DOOR

1A 1B
1B
3
4A
4B
5A
5B
5B
6A
7A
7B
8A
8B
ENEN
00. CONTENT 01. SAFETY INSTRUCTIONS
INDEX STANDARDS TO FOLLOW
STANDARDS TO FOLLOW
COMPONENTS
TECHNICAL SPECIFICATIONS
INSIDE THE PACKAGE
DIMENSIONS
PRE-INSTALLATION INFO
MANUAL OPENING/CLOSING
FIXING THE SAFE PROFILE
FIXING THE LATERAL GUIDES
FIXING ENGINE COVERAGE
FIXING THE MANEUVERS BOARD
LIMIT-SWITCHES ADJUSTMENT
01. SAFETY INSTRUTIONS
02. THE AUTOMATISM
03. INSTALLATION
ATTENTION:
This product is certified in accordance with European Community
(EC) safety standards.
This product complies with Directive 2011/65/EU of the European
Parliament and of the Council, of 8 June 2011, on the restriction of
the use of certain hazardous substances in electrical and electronic
equipment.
(Applicable in countries with recycling systems).
This marking on the product or literature indicates that the product
andelectronicaccessories(eg.Charger,USBcable,electronicmaterial,
controls, etc.) should not be disposed of as other household waste at
the end of its useful life. To avoid possible harm to the environment
or human health resulting from the uncontrolled disposal of waste,
separate these items from other types of waste and recycle them
responsibly to promote the sustainable reuse of material resources.
Home users should contact the dealer where they purchased this
product or the National Environment Agency for details on where and
how they can take these items for environmentally safe recycling.
Business users should contact their vendor and check the terms and
conditions of the purchase agreement. This product and its electronic
accessories should not be mixed with other commercial waste.
This marking indicates that the product and electronic accessories
(eg. charger, USB cable, electronic material, controls, etc.) are
susceptible to electric shock by direct or indirect contact with
electricity. Be cautious when handling the product and observe all
safety procedures in this manual.

2A 2B
ENEN
01. SAFETY INSTRUCTIONS 01. SAFETY INSTRUCTIONS
STANDARDS TO FOLLOW STANDARDS TO FOLLOW
• It is important for your safety that these instructions are followed.
• Keep these instructions in a safe place for future reference.
• The ELECTROCELOS S.A. is not responsible for the improper use of the product,
or other use than that for which it was designed.
• The ELECTROCELOS S.A. is not responsible if safety standards were not taken
into account when installing the equipment, or for any deformation that may
occur.
• The ELECTROCELOS S.A. is not responsible for insecurity and malfunction of
the product when used with components that were not sold by the them.
• This product was designed and manufactured strictly for the use indicated in
this manual.
• Any other use not expressly indicated may damage the product and/or can
cause physical and property damages, and will void the warranty.
• Do not make any changes to the automation components and/or their
accessories.
• Keep remote controls away from children, to prevent the automated system
from being activated involuntarily.
• The customer shall not, under any circumstances, attempt to repair or tune
the automatism. Must call qualified technician only.
• The installer must have certified professional knowledge at the level of
mechanical assemblies in doors and gates and control board programmation.
He should also be able to perform electrical connections in compliance with all
applicable regulations.
• The installer should inform the customer how to handle the product in an
emergency and provide him the manual.
• This device can be used by children 8 year old or older and persons whose
physical, sensory or mental capacities are reduced, or by persons without
experience or knowledge if they have received supervision or instructions on
the use of the device in a safe manner and understood the hazards involved.
Children should not play with the device. Cleaning and maintenance by the user
must not be carried out by unsupervised children.
• Before installing, the installer must verify that the temperature range indicated
on the automatism is appropriate to the location of the installation.
• Before installing, the installer must verify that the equipment to be automated
is in good mechanical condition, correctly balanced and opens and closes
properly.
• If the automation is to be installed at a level higher than 2,5 m above ground
level or other level of access, , should be followed the minimum safety and
health requirements for the use of work equipment workers at work in Directive
2009/104/EC of the European Parliament and of the Council of 16th September
of 2009.
• After installation, make sure that the mechanism is properly adjusted and that
the protection system and any manual unlocker works correctly.
• In order to protect the electrical cables against mechanical stress, you should
use conduit for the electrical wires, essentially on the power cable.
• When programming the control unit, pay particular attention to touching only
the location intended for that purpose. Failure to do so may result in electric
shock.

3A
11
12
7
13
15
14
16
8
10
9
1
3
5
2
6
4
EN
02. AUTOMATISM
COMPONENTS
1 • Engine cover
2 • Motor
3 • Limit-switches
4 • Crank
5 • Support plate (motor)
6 • Unlocking lever
7 • Control Board
8 • Stop
9 • Open
10 • Close
11 • Lateral guides
12 • Photocell
13 • Aluminum safe profile
14 • Tarpaulin
15 • Support plate
16 • Photocell mirror

4A 4B
ENEN
02. AUTOMATISM 02. AUTOMATISM
TECHNICAL SPECIFICATIONS INSIDE PACKAGE
Inside the package you will find the following components:
• 01 Motor
• 01 Motor Coverage
• 02 Lateral Guides
• 01 Safe aluminum profile
• 01 Tarpaulin
• 01 Control board
• 01 Photocells Set
• 01 Exterior Push Button
• 01 Metal Plates for Guides Fixation
• 01 User’s Manual
Motor
Motor
Coverage
Lateral
Guides
User’s
Manual
Control
Board
Tarpaulin
Metal Plates for
Guides Fixation
Metal
Plates for
Guides
Fixation
• Manufactured with own profiles of white lacquered aluminum;
• It can have up to  reinforcing bars;
• Suitable for areas with low air pressure.
Safe
Aluminum Profile
MOTOR
• Power supply V /Hz V /Hz
• Power 370W 750W
• Current ,A ,A
• RPM RPM RPM
• Noise level dB dB
• Torque Nm Nm
• Working temperature -C to C -C to C
• Protection level IP4IP4
• Working frequency Intensive Intensive
• Isolation class Class F Class F
TARPAULIN
• Wire  dtex PES HT
• Weight g/m
• Tensile strength N/cm
• Tear resistance N
• Adherence N/cm
• Finishing Varnish on both sides
• Operating temperature -C to C
The 370W motor is used on doors with a maximum height and width of 2500mm. Above
this is used 750W motor.

5A 5B
40mm
281mm
100mm
140mm
291mm
185mm
185mm
40mm
422mm
238mm
275mm
390mm
250mm
26mm
300mm
195mm
222mm
205mm A
ENEN
02. AUTOMATISM 03. INSTALLATION
DIMENSIONS PRE-INSTALLATION INFO
MANUAL OPENING/CLOSING
For a proper ECO PLUS RAPID DOOR function, check the following parameters before installing the
automatism:
• Read all steps at least once in order to get familiar with the installation and configuration
process.
• Check the horizontal alignment of the ground so that the door can be correctly assembled.
• Make sure there is an adequate protection against electrical shorts/current peaks and
ground wire connection in Electrical Box.
• Be careful handling directly the control board. Improper handling can damage some
electrical components and even cause damage to the user.
• Make sure you have all the necessary materials prepared for installation.
• Evaluate the security devices to install. This will ensure that unexpected accidents do not
occur.
To open or close the door manually, simply pull
and hold down the unlock lever (6) and use a 6mm
hexagon wrench to rotate the screw installed in the
bottom of the engine, as shown on the image.
• Turning to the right will open the door and
turning to the left will close.
• To facilitate the task, use an automatic screwdriver
to quickly turn the screw.
It is very important that all precautions are adhered to!
Only in this way the correct functioning and durability of automatism can be achieved!
Wall
Wall

6A 6B
115mm
C
DE
F
G H
B
ENEN
1 • Apply the safe to the wall, talking into account the horizontal leveling and the measures
indicated (B and C).
The safe should also be centered with the door’s free space.
Based on existing holes in the support plates, mark the locations for drilling (D and E).
2• Make holes at the marked locations, and then apply the safe profile on the wall and secure
with expansion bolts and screws (F).
The safe must be properly secured in order to avoid accidents (G and H).
03. INSTALLATION 03. INSTALLATION
SAFE PROFILE FIXATION SAFE PROFILE FIXATION
(FREE DOOR SPACE)

7A 7B
L
M
O
I J
K
N
ENEN
03. INSTALLATION 03. INSTALLATION
LATERAL GUIDES FIXATION LATERAL GUIDES FIXATION
4 • Attach the lateral guides on the support plates with
screw, tightening them in the nuts located on the guides.
5 • Fix the lateral guides to the ground using the
existing plates. Start by making the holes in the
ground using the existing holes on plates for
the application of screws. Finally, tightening the
screws until the guide is properly secure.
3 • Unlock the motor pulling the lever down (see page 5B) and manually pull the tarpaulin
down for about 500mm as visible in (I).
Now apply the lateral guides, by placing them at the inner side of the support plates and
against the wall. The tarpaulin should be inside the guides (J), so that it can move up and
down always within guides.
FIXING ENGINE COVERAGE
1 • Fit the motor cover to make the markings.
2 • Drill holes in the wall.
3 • Apply the cover and tighten the 2 screws on the upper part (P). Finish by tightening the
cover to the plate already in the safe (Q).

8A 8B
NONC
COM
19
18
19
18
P
Q U
RS
T
ENEN
03. INSTALLATION 03. INSTALLATION
CONTROL BOARD FIXATION LIMIT-SWICHES ADJUSTMENT
1 • Determine the drilling location.
2 • Make the drilling in the wall.
3 • Fix the control board case on the wall. Must use screws with expansion bolts (screws and
expansion bolts not provided in this kit).
NOTE • The red ring must activate it’s micro-switch
by the bottom and the white ring must do it by the
top, as shown in the picture to the left.
Microswitch connections:
1 • Manually put the door in the desired opening position using the handcrank.
2
• Rotatethetuningscrew18(red)untiltheredringofthelimit-switch activates the correspondend
micro-switch.
3
• Manually put the door in the desired closing position using the handcrank.
4
• Turn the tuning screw 19 (white) until the white ring of the limit-switch activates the
correspondend micro-switch.
red
open
white
close