Motorline professional ECO FAST DOOR Use and care manual

v3.1
REV. 06/2018
EN
USER’S AND INSTALLER’S MANUAL
ECO FAST DOOR

1A 1B
ENEN
1B
3A
3B
4B
4B
5A
6A
7A
7B
8
STANDARDS TO FOLLOW
INSIDE THE PACKAGE
TECHNICAL SPECIFICATIONS
PRE-INSTALLATION INFO
MANUAL OPENING/CLOSING
SAFE PROFILE FIXATION
LATERAL GUIDES FIXATION
CONTROL BOARD FIXATION
LIMIT-SWITCHES ADJUSTMENT
INSTALLATION MAP
01. SAFETY INSTRUTIONS
02. THE PACKAGE
03. THE AUTOMATISM
04. INSTALLATION
00. CONTENT 01. SAFETY INSTRUCTIONS
INDEX STANDARDS TO FOLLOW
ATTENTION:
This product is certified in accordance with European Community
(EC) safety standards.
This product complies with Directive 2011/65/EU of the European
Parliament and of the Council, of 8 June 2011, on the restriction
of the use of certain hazardous substances in electrical and
electronic equipment.
(Applicable in countries with recycling systems).
This marking on the product or literature indicates that the
product and electronic accessories (eg. Charger, USB cable,
electronic material, controls, etc.) should not be disposed of
as other household waste at the end of its useful life. To avoid
possible harm to the environment or human health resulting
from the uncontrolled disposal of waste, separate these items
from other types of waste and recycle them responsibly to
promote the sustainable reuse of material resources. Home users
should contact the dealer where they purchased this product or
the National Environment Agency for details on where and how
they can take these items for environmentally safe recycling.
Business users should contact their vendor and check the terms
and conditions of the purchase agreement. This product and its
electronic accessories should not be mixed with other commercial
waste.
This marking indicates that the product and electronic accessories
(eg. charger, USB cable, electronic material, controls, etc.) are
susceptible to electric shock by direct or indirect contact with
electricity. Be cautious when handling the product and observe all
safety procedures in this manual.

2A 2B
ENEN
01. SAFETY INSTRUCTIONS01. SAFETY INSTRUCTIONS
STANDARDS TO FOLLOWSTANDARDS TO FOLLOW
level or other level of access, , should be followed the minimum safety and
health requirements for the use of work equipment workers at work in Directive
2009/104/EC of the European Parliament and of the Council of 16th September
of 2009.
• In the case of the equipment where the automation will be installed, have
a pedestrian door, be aware that it must be closed when the automation is
activated.
• After installation, make sure that the mechanism is properly adjusted and that
the protection system and any manual unlocker works correctly.
• In order to protect the electrical cables against mechanical stress, you should
use conduit for the electrical wires, essentially on the power cable.
• When programming the control unit, pay particular attention to touching only
the location intended for that purpose. Failure to do so may result in electric
shock.
• It is important for your safety that these instructions are followed.
• Keep these instructions in a safe place for future reference.
• The ELECTROCELOS S.A. is not responsible for the improper use of the product,
or other use than that for which it was designed.
• The ELECTROCELOS S.A. is not responsible if safety standards were not taken
into account when installing the equipment, or for any deformation that may
occur.
• The ELECTROCELOS S.A. is not responsible for insecurity and malfunction of the
product when used with components that were not sold by the them.
• This product was designed and manufactured strictly for the use indicated in
this manual.
• Any other use not expressly indicated may damage the product and/or can
cause physical and property damages, and will void the warranty.
• Do not make any changes to the automation components and/or their
accessories.
• Keep remote controls away from children, to prevent the automated system
from being activated involuntarily.
• The customer shall not, under any circumstances, attempt to repair or tune the
automatism. Must call qualified technician only.
• The installer must have certified professional knowledge at the level of
mechanical assemblies in doors and gates and control board programmation.
He should also be able to perform electrical connections in compliance with all
applicable regulations.
• The installer should inform the customer how to handle the product in an
emergency and provide him the manual.
• This device can be used by children 8 year old or older and persons whose
physical, sensory or mental capacities are reduced, or by persons without
experience or knowledge if they have received supervision or instructions on
the use of the device in a safe manner and understood the hazards involved.
Children should not play with the device. Cleaning and maintenance by the user
must not be carried out by unsupervised children.
• Before installing, the installer must verify that the temperature range indicated
on the automatism is appropriate to the location of the installation.
• Before installing, the installer must verify that the equipment to be automated
is in good mechanical condition, correctly balanced and opens and closes
properly.
• If the automation is to be installed at a level higher than 2,5 m above ground

3A 3B
ENEN
02. PACKAGE 03. AUTOMATISM
INSIDE PACKAGE TECHNICAL SPECIFICATIONS
Inside the package you will find the following components:
•01 Motor
• 02 Lateral Guides
•01 Safe aluminum profile
•01 Tarpaulin
•01 Control board
•01 Photocells Set MF101
•01 Exterior Push Button
•01 Metal Plates for Guides Fixation
•01 User’s Manual
•01 U
Motor Safe
Aluminum Profile
Engine
Coverage
Lateral
Guides
User’s
Manual
Control
Board
Tarpaulin
Metal Plates for
Guides Fixation
Metal
Plates for
Guides
Fixation
MOTOR
• Power supply V /Hz
• Power W
• Current ,A
• RPM RPM
• Noise level dB
• Torque ,Nm
• Working temperature -C to C
• Protection level IP4
• Working frequency Intensiva
• Isolation class Classe F
TARPAULIN
• Wire  dtex PES HT
• Weight g/m
• Tensile strength N/cm
• Tear resistance N
• Adherence N/cm
• Finishing Varnish on both sides
• Working temperature -C to C
Eco fast doors are built in special aluminum profiles with white power coutting finish and suitable
for areas with low wind pressure.
With  reinforcement bars.
MOTOR

4A 4B
35mm
máx.3000mm
100mm
285mm
160mm
251mm
40mm
417mm
153mm
215mm
255mm
155mm
163mm
20mm
250mm
26mm
300mm
195mm
222mm
205mm
ENEN
03. AUTOMATISM 04. INSTALLATION
CARACTERÍSTICAS TÉCNICAS PRE-INSTALLATION INFO
MANUAL OPENING/CLOSING
máx: 3200mm
Largura
Vão Livre
máx:3000mm
For a proper ECO FAST DOOR function, check the following parameters before installing the auto-
matismo:
• Read all steps at least once in order to get familiar with the installation and configuration
process.
• Check the horizontal alignment of the ground so that the door can be correctly assemb-
led.
• Make sure there is an adequate protection against electrical shorts / current peaks and
ground wire connection in Electrical Box.
• Be careful handling directly the control board. Improper handling can damage some elec-
trical components and even cause damage to the user.
• Make sure you have all the necessary materials prepared for installation.
• Evaluate the safety devices to be installed. This will ensure that unexpected accidents do
not happen.
To open or close the door manually, simply pull and
hold down the unlock lever in the shaded image
and use a mm hexagon wrench to rotate the screw
installed in the bottom of the engine, as shown on
the image.
• Rotating to the right will open the door and
Rotating to the left will close it.
To facilitate the task use an automatic screw machi-
ne, in order to rapidly rotate the screw.
- For every  turns, the door will go up/down about
mm.
It is very important that all precautions are respected!
Only in this way the correct functioning and durability of automatism can be
achieved!

5A 5B
(Vão de Obra)
ENEN
1• Apply the safe aluminum profile in the wall’s installation location as shown in (A), taking
into account the horizontal position and the measures indicated in (B).
The safe should also be centered with the door’s free space.
Based on existing holes in the support plates, mark the locations for drilling - scheme (C).
2• Make holes at the marked locations, and then apply the safe profile on the wall and
secure with expansion bolts and screws - scheme (D).
The safe must be firmly fixed so that accidents do not occur.
In the scheme (E) is visible the safe already properly tightened.
04. INSTALLATION 04. INSTALLATION
SAFE PROFILE FIXATION SAFE PROFILE FIXATION
(FREE DOOR SPACE)

6A 6B
ENEN
04. INSTALLATION 04. INSTALLATION
LATERAL GUIDES FIXATION LATERAL GUIDES FIXATION
4 • Attach the lateral guides on the support
plates with screw, tightening them in the
nuts located on the guides.
5 • Fix the lateral guides to the ground using
the existing plates. Start by making the
holes in the ground using the existing holes
on plates for the application of screws.
Finally, fasten the screws until the guide is
properly secure.
3 • Unlock the motor pulling the lever down (see page 06.A ) and manually pull the tar-
paulin down for about 500mm as visible in (F).
Now apply the lateral guides, by placing them at the inner side of the support plates and
against the wall (G).
The tarpaulin should be inside the guides (H), so that it can move up and down always
within guides.

7A 7B
PARAFUSOS
BUCHAS
18
19
NONC
COM
18
19
19
18
ENEN
04. INSTALLATION 04. INSTALLATION
CONTROL BOARD FIXATION LIMIT-SWICHES ADJUSTMENT
1 • Taking into account the indicated measures, determine the drilling location.
2 • Make the drilling in the wall.
3 • Fix the control board case on the wall. Must use screws with expansion bolts (screws
and expansion bolts not provided in this kit).
EXPANSION
BOLTS
SCREWS
NOTE • The red ring must activate it’s micro-switch
by the bottom and the white ring must do it by the
top, as shown in the picture to the left.
Microswitch connections:
01 • Manually put the door in the desired opening position using the handcrank.
02 • Rotate the tuning screw 18 (red) until the red ring of the limit-switch activates the
correspondend micro-switch.
03 • Manually put the door in the desired closing position using the handcrank.
04 • Rotate the tuning screw 19 (white) until the white ring of the limit-switch activates the
correspondend micro-switch.
red
open
white
close

8A8
A
C
D
B
04
08
02
04
10
12
13
01
01
02
04
11
03
06
07
05
14
09
EN
04. INSTALLATION
INSTALLATION MAP
LEGEND:
01 • Aluminum safe profile
02 • Safe profile’s support plate
03 • Motor
04 • Lateral guides
05 • Motor unlock lever
06 • Limit-switches support
07 • Limit-switches
08 • Tarpaulin
09 • Control board
10 • Guides fixing metal plates to ground
11 • Conection Plug
12 • Photocells
13 • Photocells support plate
14 • Engine Coverage
AB
CD