Motorline professional KVM25 Use and care manual

V3.0
REV. 03/2017
KVM25
EN
USER’S AND INSTALLER’S MANUAL

2A 2B1A 1B
1B
2A
2B
3A
3B
4A
5B
6A
ENEN
STANDARDS TO FOLLOW
INSIDE THE PACKAGE
LOCK/UNLOCK
TECHNICAL SPECIFICATIONS
01. SAFETY INSTRUCTIONS
02. THE PACKAGE
03. THE AUTOMATISM
PRE-INSTALLATION INFO
AUTOMATISM INSTALLATION
INSTALLATION MAP
04. INSTALLATION
00. CONTENTS 01. SAFETY INSTRUCTIONS
INDEX STANDARDS TO FOLLOW
PROGRAMMING THE LIMIT SWITCHES
05. PROGRAMMING
• It is important for your safety that these instructions are followed.
• Keep these instructions in a safe place for future reference.
• The ELECTROCELOS S.A. is not responsible for the improper use of the product, or other use than that for which it was
designed.
• The ELECTROCELOS S.A. is not responsible if safety standards were not taken into account when installing the
equipment, or for any deformation that may occur.
• The ELECTROCELOS S.A. is not responsible for insecurity and malfunction of the product when used with components
that were not sold by the them.
• This product was designed and manufactured strictly for the use indicated in this manual.
• Any other use not expressly indicated may damage the product and/or can cause physical and property damages, and
will void the warranty.
• Do not make any changes to the automation components and/or their accessories.
• Keep remote controls away from children, to prevent the automated system from being activated involuntarily.
• The customer shall not, under any circumstances, attempt to repair or tune the automatism. Must call qualified
technician only.
• The installer must have certified professional knowledge at the level of mechanical assemblies in doors and gates
and control board programmation. He should also be able to perform electrical connections in compliance with all
applicable regulations.
• The installer should inform the customer how to handle the product in an emergency and provide him the manual.
ATTENTION:
This product is certified in accordance with European Community (EC) safety standards.
This product complies with Directive 2011/65/EU of the European Parliament and of the Council,
of 8 June 2011, on the restriction of the use of certain hazardous substances in electrical and
electronic equipment.
(Applicable in countries with recycling systems).
This marking on the product or literature indicates that the product and electronic accessories
(eg. Charger, USB cable, electronic material, controls, etc.) should not be disposed of as other
household waste at the end of its useful life. To avoid possible harm to the environment or human
health resulting from the uncontrolled disposal of waste, separate these items from other types of
waste and recycle them responsibly to promote the sustainable reuse of material resources. Home
users should contact the dealer where they purchased this product or the National Environment
Agency for details on where and how they can take these items for environmentally safe recycling.
Business users should contact their vendor and check the terms and conditions of the purchase
agreement. This product and its electronic accessories should not be mixed with other commercial
waste.
This marking indicates that the product and electronic accessories (eg. charger, USB cable, electronic
material, controls, etc.) are susceptible to electric shock by direct or indirect contact with electricity. Be
cautious when handling the product and observe all safety procedures in this manual.

3A 3B
1
2
3
8
9
10
6
7
4
5
2A 2B
ENEN
02. THE PACKAGE 03. THE AUTOMATISM
INSIDE THE PACKAGE LOCK/UNLOCK
Inside the package you will find the following components: The automatism unlock function allows the user to open and close the gate manually, wi-
thout having to remove the motor from the installation site.
This funcionality is specially important in emergency cases and/or power cuts.
To lock or unlock the automatism just pull down the lever as shown in the following image.
The lever has a spring that will bring it up to the starting point.
Each time you pull the lever down and rise completely, you will unlock or lock the automa-
tism.
When pulling down, a small sound of gears engaging means that the lock/unlock was suc-
cessfully performed.
• 01 automatism KVM
• 01 maneuver board
• 02 four channel transmitters MXSP
• 01 mounting plate
• 01 chain
• 01 pinion for Ømm shaft
• 01 bearing bracket
• 04 fixing screws
• 01 unlocking cord
• 01 user manual
6
7
8
9
10
1
2
3
4
5

4A 4B
430mm
530máx.
230mm
60mm
148,5mm
3A 3B
ENEN
03. THE AUTOMATISM 04. INSTALLATION
TECHNICAL SPECIFICATIONS PRE-INSTALLATION INFO
KVM specifications are as follow:
KVM dimensions are the following:
• Power Supply AC 230V 50/60Hz
• Power 80W
• Current 8A
• RPM 20 RPM
• Noise level <65dB
• Force 30N
• Operating temperatures -25°C a 65°C
• Transformer 100W
• Protection class IP20
• Work Rate 30ciclos / h
• Fuses 220V 1A - 24V 10A
For a proper installation and a durable performance of KVM, be aware of the following
parameters:
• Please read all steps of this manual at least once, so that you know the full process before
starting the real assembling.
• This equipment can only be installed on sectional doors with a maximum area of m.
• Please make sure that the door’s structure is solid and in good conditions to be automated.
• Make sure that the sectional door has no mechanical anomalies, they may affect the auto-
matism’s durability .
• To check if the door is in good condition for the motor to be installed, manually raise it to
mm, mm and mm from the floor and drop it.
The door must remain suspended in that position or going down very slightly.
If this does not happen, check the springs condition.
• Check the surrounding space. Carefully evaluate potential dangers that can cause physical
damage and possible contact with bugs, infiltrations or others.
• Please make sure that the automatism will be connected to a V power supply, protected
with earth wire.
• Please check if there is apropriate electronic protection against short-circuits/current
peaks, and earth wire on the main electric board.
• Be carefull in case of manually operating the control board. The incorrect usage can dama-
ge some sensible electronic components.
• Check if you have all the necessary material ready for the installation.
• Check all safety devices to install. This will ensure that unexpected accidents won’t happen.
It is very important that before installation, make sure the springs are adjusted
according to the door’s weight!

5A 5B4A 4B
ENEN
04. INSTALLATION 04. INSTALLATION
AUTOMATISM INSTALLATION AUTOMATISM INSTALLATION
In the illustrated diagrams below and on the following page, are represented the procedures
for proper installation of the motor KVM.
01 - Place the pinion on the Ømm spring’s shaft of the sectional door.
04 - Slightly loosen the bearing bracket’s
screws (left),to be able to move it sideways.
05 - Pull the metal plate to the wall and se-
cure with the screws.
After fixing the plate, tighten the bearing
bracket’s screws back to fix it too.
06 - Pull the pinion to the bearing and tighten the two bolts to secure the pinion to the shaft.
02 - Place the chain over the pinion leaving
it hanged.
03 - Pass the Ømm shaft through the bearing on the support plate.
It is very important that these quotas are respected! Only in this way the correct
functioning and durability of automatism can be assured!

6A 6B
01
06
02
04
03
05
02
01
5A 5B
ENEN
07 - Place the automatism on the support plate (left), and assemble the chain on the motor’s
pinion as you can see on the right image.
Place the screws on the motor in order to support it on the metal plate, without tightening
them completely, so that you are able to adjust the automatism.
08 - With the bolts still loose, pull the engine down in order to tighten the chain.
While pulling down, fasten the  motor bolts to secure it on the support plate. The automa-
tism is now installed.
LEGEND:
• motor KVM
• support plate
• chain
• pinion for Ømm shaft
• bearing bracket
• Ømm sectional door’s shaft
01
02
03
04
05
06
04. INSTALLATION
AUTOMATISM INSTALLATION INSTALLATION MAP
04. INSTALLATION

7A 7B6A 6B
ENEN
05. PROGRAMMING 05. PROGRAMMING
PROGRAMMING LIMIT SWITCHES PROGRAMMING LIMIT SWITCHES
In the illustrated diagrams below and on the following page are represented the procedures
for proper programming of the motor KVM limit switches, once installed on the gate.
01 - Unlock the motor, pulling the lever
down. You will hear a little click when
pulling down, and then you must let the
lever go up.
05 - Move the plastic piece until hear a click
from the micro.
03 - Slightly loosen the  screws of the
magnetic actuator. 07 -
Move the plastic piece until hear a click
from the micro. Now tighten the  screws of
the magnetic actuator.
02 - Open the automatism cover with a
screwdriver and connect the motor to a
power source at V.
06 - Manually move the door to the open
position.
04 - Manually pull the door into the closed
position. 08 - Lock the motor and test the door ope- ning and closing using either the "PUSH"
button on the control board or the trans-
mitter. If necessary, repeat the previous
steps, from the image , to better tune
the limit switches.
It is very important that these quotas are respected! Only in this way the correct
functioning and durability of automatism can be assured!