Motorline professional SUBWING 700 Use and care manual

V 1.1
REV. 04/2019
SUBWING 700
EN
USER’S AND INSTALLER’S MANUAL

A B
1B
2A
3A
3B
4A
4B
5A
5B
2A
A B
2B
2B
5A
ENEN
00. CONTENT 01. SAFETY INSTRUCTIONS
INDEX STANDARDS TO FOLLOW
STANDARDS TO FOLLOW
CONNECTION SCHEME
INSTALLATION MAP
GATE WING OPENING ANGLE
BOX INSTALLATION
ASSEMBLING THE OPERATOR AND LEVERS
FASTENING THE OPERATOR LEVER TO THE GATE
EMERGENCY RELEASE PROCEDURE
. SAFETY INSTRUCTIONS
. OPERATOR
. INSTALLATION
FINAL CONSUMERS AND SPECIALIZED INSTALLERS INSTRUCTIONS
. TROUBLESHOOTING
2B
TECHNICAL SPECIFICATIONS
2B
DIMENSIONS
5A
LIMIT SWITCHES ASSEMBLY (OPTIONAL)
• It is important for your safety that these instructions are followed.
• Keep these instructions in a safe place for future reference.
• The ELECTROCELOS S.A. is not responsible for the improper use of the product, or other use than that for which it was
designed.
• The ELECTROCELOS S.A. is not responsible if safety standards were not taken into account when installing the
equipment, or for any deformation that may occur.
• The ELECTROCELOS S.A. is not responsible for insecurity and malfunction of the product when used with components
that were not sold by the them.
• This product was designed and manufactured strictly for the use indicated in this manual.
• Any other use not expressly indicated may damage the product and/or can cause physical and property damages, and
will void the warranty.
• Do not make any changes to the automation components and/or their accessories.
• Keep remote controls away from children, to prevent the automated system from being activated involuntarily.
• The customer shall not, under any circumstances, attempt to repair or tune the automatism. Must call qualified
technician only.
• The installer must have certified professional knowledge at the level of mechanical assemblies in doors and gates
and control board programmation. He should also be able to perform electrical connections in compliance with all
applicable regulations.
• The installer should inform the customer how to handle the product in an emergency and provide him the manual.
ATTENTION:
This product is certified in accordance with European Community (EC) safety standards.
This product complies with Directive 2011/65/EU of the European Parliament and of the Council,
of 8 June 2011, on the restriction of the use of certain hazardous substances in electrical and
electronic equipment.
(Applicable in countries with recycling systems).
This marking on the product or literature indicates that the product and electronic accessories
(eg. Charger, USB cable, electronic material, controls, etc.) should not be disposed of as other
household waste at the end of its useful life. To avoid possible harm to the environment or human
health resulting from the uncontrolled disposal of waste, separate these items from other types of
waste and recycle them responsibly to promote the sustainable reuse of material resources. Home
users should contact the dealer where they purchased this product or the National Environment
Agency for details on where and how they can take these items for environmentally safe recycling.
Business users should contact their vendor and check the terms and conditions of the purchase
agreement. This product and its electronic accessories should not be mixed with other commercial
waste.
This marking indicates that the product and electronic accessories (eg. charger, USB cable, electronic
material, controls, etc.) are susceptible to electric shock by direct or indirect contact with electricity. Be
cautious when handling the product and observe all safety procedures in this manual.

A BA B
1
2
2
3
4
5
5
6
7
8
RG58/9
230V AC
230mm
375mm
320mm
65mm
165mm
119mm
329mm
227mm
141mm
ENEN
02. OPERATOR 02. OPERATOR
CONNECTION SCHEME TECHNICAL SPECIFICATIONS
1• Motor
2 • External photocell 3 • Flashing warning light 4 • Antenna 5 • Internal photocell 6 • Electronic control unit 7 • Key-switch 8 • Remote control
V V
• Max. weight of gate Kg
• Max. width of gate ,m
• Motors power supply V DC V AC
• Motor power W W
• Motor RPM  
• Condenser - ,F
• Mechanical unlock for emergency With key
• Working temperature -C/C
• Weight Kg
• Protection IP
• Opening time   sec
• Force of thrust Nm
• Motor current input A ,A
INSTALLATION MAP
DIMENSIONS
x,mm (V DC)
x,mm (V DC)
x,mm
x
,mm
x,mm
x,mm
Alimentation V
Photocell RX Photocell TX
x,mm

A BA B
72mm
375mm
320mm
C1
F 2
F 1
165mm
ENEN
BOX INSTALLATION
03. INSTALLATION
GATE WING OPENING ANGLE
03. INSTALLATION
Establish the required opening angle.
1• Dig a hole big enough to hold
the box containing the operator
(C1).
2• Insert the tube for water
drainage in the prepared hole (F1).
3• Insert the sheath for laying the
power cables (F2).
Note: while positioning the box,
keep in mind the minimum
distance there must be between
the pillar and the centre of rotation
of the gate hinge.
4 • Cement so that the box cannot
be moved, wait for it to dry and
then assemble the operator and
levers.
Distance between
Pillar - Hinge Centre
BOX
POSITION
BOX
POSITION


INTERNAL VIEW
INTERNAL VIEW
PILLAR
PILLAR

A BA B
L 1
L
ENEN
ASSEMBLING THE OPERATOR AND LEVERS FASTENING THE OPERATOR LEVER TO THE GATE
03. INSTALLATION 03. INSTALLATION
1• Insert the motor into the foundation case and
fixit with nuts and washers supplied. Insert the cover and fasten it with the screws
provided Position.
Position the gate wing and the lever (L) so that
they are perfectly aligned and fasten them by
welding or similar.
2• Insert the ball in the pin located on the box
and fit the gate anchorage lever (L1).
3• Put the connection lever(L2) between the
levers (L3) and (L1) and block it with screws and
washers supplied
BALL
welding
L
L
L
L

A BA B
L 1
V
C
ENEN
03. INSTALLATION
EMERGENCY RELEASE PROCEDURE FINAL CONSUMERS AND SPECIALIZED INSTALLERS INSTRUCTIONS
Insert the key C provided into the
appropriate hole on the lever L1 and
turn the key.
Insert, regulate and block the mechanical limit switches in the desired position.
04. TROUBLESHOOTING
LIMIT SWITCHES ASSEMBLY (OPTIONAL)
Closing Opening
Problem Probable cause Solution
• On giving a command with
the remote control or with the
key-switch, the gate doesn’t
open or the motor doesn’t start
• 230V mains voltage absent • Check master switch
• Emergency STOP present
• Check for any STOP
selectors or commands.
If not used, check jumper
on STOP contact input on
the control board
• Fuse blown • Replace with one of same
value.
• Power cable of motor or
motors not connected or faulty
• Connect the cable to
appropriate terminal or
replace.
• The photocell is not
functioning or the beam is
interrupted
• Check the connection, remove
any obstacle across the beam
• On giving a command with
the remote control, the gate
doesn’t open but works with
the key command
• The remote control has not
been memorised or the battery
is flat
• Carry out the remote control
learning procedure on the
radio receiver or replace the
battery with a new one
• The gate starts, but stops
immediately • The force of the motor or motors is insufficient
• Modify the value with the
FORCE trimmer on the control
unit
• One wing opens and the
other closes • The connection is not correct • Invert the connection of the
cable of the motor which rota-
tes in the wrong sense