Motorline professional MPXR82MFS User manual

V1.0
REV. 05/2021
MPXR82MFS
MPXR82MFS EN
USER/INSTALLER MANUAL

A B
1B
4A
4A
4B
4A
5
6
7A
11
9A
10B
7B
8A
8B
ENEN
INSTRUCTIONS FOR FINAL CONSUMERS / SPECIALIZED INSTALLERS
DIP SWITCH CONFIGURATION
DEVICE TEST
PRODUCT DESCRIPTION
INSTALLATION OF WALLMOUNT
CONNECTION TO MRAC CONTROL BOARD
EXTERNAL POWER CONNECTION
ETHERNET CONNECTION
CARACTERÍSTICAS TÉCNICAS
BASIC CONTENT
DIMENSIONS AND PRODUCT DIAGRAM
FINGERPRINT READER
OPERATING SHCEME
. SAFETY INSTRUCTIONS
. TROUBLESHOOTING
. DIP SWITCH
. COMPONENTS TEST
. PRODUCT
. INSTALLATION
.CONNECTION SCHEME
01. SAFETY INSTRUCTIONS
This product is certified in accordance with European
Community (EC) safety standards.
This product complies with Directive 2011/65/EU of the
European Parliament and of the Council, of 8 June 2011, on
the restriction of the use of certain hazardous substances in
electrical and electronic equipment.
(Applicable in countries with recycling systems).
This marking on the product or literature indicates that the
product and electronic accessories (eg. Charger, USB cable,
electronic material, controls, etc.) should not be disposed
of as other household waste at the end of its useful life. To
avoid possible harm to the environment or human health
resulting from the uncontrolled disposal of waste, separate
these items from other types of waste and recycle them
responsibly to promote the sustainable reuse of material
resources. Home users should contact the dealer where they
purchased this product or the National Environment Agency
for details on where and how they can take these items
for environmentally safe recycling. Business users should
contact their vendor and check the terms and conditions
of the purchase agreement. This product and its electronic
accessories should not be mixed with other commercial
waste.
This marking indicates that the product and electronic
accessories (eg. charger, USB cable, electronic material,
controls, etc.) are susceptible to electric shock by direct or
indirect contact with electricity. Be cautious when handling
theproductandobserveallsafetyproceduresinthismanual.
ATTENTION:
00. CONTENT
INDEX

A B
ENEN
GENERAL WARNINGS
•This manual contains very important safety and usage information.
very important. Read all instructions carefully before beginning the
installation/usage procedures and keep this manual in a safe place
that it can be consulted whenever necessary.
•This product is intended for use only as described in this manual. Any
other enforcement or operation that is not mentioned is expressly
prohibited, as it may damage the product and put people at risk
causing serious injuries.
•Thismanual is intendedfirstlyforspecialized technicians, and does not
invalidate the user’s responsibility to read the “User Norms” section in
order to ensure the correct functioning of the product.
•The installation and repair of this product may be done by qualified
and specialized technicians, to assure every procedure are carried
out in accordance with applicable rules and norms. Nonprofessional
and inexperienced users are expressly prohibited of taking any action,
unless explicitly requested by specialized technicians to do so.
•Installations must be frequently inspected for unbalance and the
wear signals of the cables, springs, hinges, wheels, supports and other
mechanical assembly parts.
•Do not use the product if it is necessary repair or adjustment is
required.
•When performing maintenance, cleaning and replacement of parts,
the product must be disconnected from power supply. Also including
any operation that requires opening the product cover.
•The use, cleaning and maintenance of this product may be carried
out by any persons aged eight years old and over and persons whose
physical,sensorialormentalcapacitiesarelower,orbypersonswithout
any knowledge of the product, provided that these are supervision
and instructions given by persons with experienced in terms of usage
of the product in a safe manner and who understands the risks and
dangers involved.
•Children shouldn’t play with the product or opening devices to avoid
01. SAFETY INSTRUCTIONS
the motorized door or gate from being triggered involuntarily.
WARNINGS FOR TECHNICIANS
•Before beginning the installation procedures, make sure that you have
all the devices and materials necessary to complete the installation
of the product.
•You should note your Protection Index (IP) and operating temperature
to ensure that is suitable for the installation site.
•Provide the manual of the product to the user and let them know how
to handle it in an emergency.
•If the automatism is installed on a gate with a pedestrian door, a door
locking mechanism must be installed while the gate is in motion.
•Do not install the product “upside down” or supported by elements do
not support its weight. If necessary, add brackets at strategic points
to ensure the safety of the automatism.
•Do not install the product in explosive site.
•Safety devices must protect the possible crushing, cutting, transport
and danger areas of the motorized door or gate.
•Verify that the elements to be automated (gates, door, windows,
blinds, etc.) are in perfect function, aligned and level. Also verify if the
necessary mechanical stops are in the appropriate places.
•The centralmust beinstalledon a safeplace of any fluid(rain, moisture,
etc.), dust and pests.
•You must route the various electrical cables through protective tubes,
to protect them against mechanical exertions, essentially on the
power supply cable. Please note that all the cables must enter the
central from the bottom.
•If the automatism is to be installed at a height of more than 2,5m from
the ground or other level of access, the minimum safety and health
requirements for the use of work equipment workers at the work of
Directive 2009/104/CE of European Parliament and of the Council of 16
September 2009.
•Attach the permanent label for the manual release as close as possible

A B
ENEN
to the release mechanism.
•Disconnect means, such as a switch or circuit breaker on the electrical
panel, must be provided on the product’s fixed power supply leads in
accordance with the installation rules.
•If the product to be installed requires power supply of 230Vac or
110Vac, ensure that connection is to an electrical panel with ground
connection.
•The product is only powered by low voltage satefy with central (only
at 24V motors)
WARNINGS FOR USERS
•Keep this manual in a safe place to be consulted whenever necessary.
•If the product has contact with fluids without being prepared, it must
immediately disconnect from the power supply to avoid short circuits,
and consult a specialized technician.
•Ensure that technician has provided you the product manual and
informed you how to handle the product in an emergency.
•Ifthesystemrequiresanyrepairormodification,unlocktheautomatism,
turn off the power and do not use it until all safety conditions have
been met.
•In the event of tripping of circuits breakers of fuse failure, locate
the malfunction and solve it before resetting the circuit breaker or
replacing the fuse. If the malfunction is not repairable by consult this
manual, contact a technician.
•Keep the operation area of the motorized gate free while the gate in in
motion, and do not create strength to the gate movement.
•Do not perform any operation on mechanical elements or hinges if the
product is in motion.
RESPONSABILITY
•Supplier disclaims any liability if:
•Product failure or deformation result from improper installation
01. SAFETY INSTRUCTIONS
SYMBOLS LEGEND:
• Important safety
notices
• Useful information
• Programming
information
• Potentiometer
information
• Connectors
information
• Buttons
information
use or maintenance!
•Safety norms are not followed in the installation, use and
maintenance of the product.
•Instructions in this manual are not followed.
•Damaged is caused by unauthorized modifications
•In these cases, the warranty is voided.

A B
01
02
03
04
05
ENEN
• Power Supply 12V DC 1A
• Current 800mA (max)
• Communication RS485 and TCP/IP
• Operating Mode Fingerprint and Mifare Card
• Card Reading Format Mifare (13.56 MHz)
• Identification speed 1,000 <= 1 sec
• ID Setting TCP/IP
• Operating Temperature -25°C a 55°C
• Operating Humidity 20% ~ 80%
• Dimension 75x135x41mm (LxAxP)
Reader for internal use with night lighting that is part of the control and management of access of a
given location.
TECHNICAL CHARACTERISTICS
01 • 01 MPXR82MFS
02 • 01 Metal Back Plate
03 • 02 Screw for fixing to the wall
04 • 01 Screw for mounting plate
05 • 01 Heist Key
BASIC CONTENT
CLOSE DOOR
CHECKS THE
FINGERPRINT
EVENTS LOG
STORED
IDENTIFICATION
MRAC
CONTROL BOARD
REGISTER CARD OR
FINGERPRINT
REGISTRATION IN THE
SOFTWARE MANAGEMENT
VERIFICATION FAILED
Please try again!
CREATE
OPEN DOOR
FINGERPRINT
DATA BASE
SUCCESSFULLY
VERIFIED
Thank you
. PRODUCT . PRODUCT
PRODUCT DESCRIPTION OPERATING SCHEME


75mm 41mm
26mm
110mm
137mm
EN
LED Status
LED Power
Connection Input
TCP/IP
Case Button
(On the back of the
mounting plate)
MIFARE Card
Area
Fingerprint
Area
Star-shaped screw hole to
secure the reader to the rear
plate
BACK PLATE FRONT
BOTTOM
SIDE BACK
. PRODUCT
DIMENSIONS AND PRODUCT DIAGRAM


EN
. PRODUCT
FINGERPRINT READER
• It is recommended to use your index finger or middle finger.
• Thumb, ring or little finger are relatively difficult to place in the correct position.
Thumb
. CHOOSE A FINGER TO ADD
. HOW TO PLACE YOUR FINGER ON THE SENSOR
Index Finger
Middle Finger
Ring Finger
Pinky Finger
1 • Place your finger in such a way that it completely covers the sensor area
with maximum contact.
2 • Place the fingerprint core in the center of the sensor. The core of a
fingerprint is a center where the spiral of the ridges is dense.
Tips for different fingerprint conditions
These fingerprint products are designed to check fingerprints more securely, regardless of
finger skin conditions. However, if a fingerprint is not read on the sensor, see the following
tips.
• If your finger is stained with sweat/water or covered with dust/impurities, clean it and try
again.
• If your finger is too dry, give some hot air from your mouth at your fingertips.
Tips for inserting fingerprints
In fingerprint recognition, the registration process is very important. When registering a
fingerprint, please try to place your finger correctly with the utmost care.
In case of low acceptance rate, the following actions are recommended:
• Delete the registered fingerprint and reregister your finger.
• Register the same fingerprint again.
• If your finger has scars or cuts that make it difficult to register, try another finger.
It is recommended to register  fingers per user with different hands, so that it is easier to
use in the event that the hand is occupied or injured.
 • If a finger is placed as shown on
the right, only a small area of the
finger is captured. Therefore, it is
recommended to place your finger
as shown on the left.
MFM-800 MFM-800
Usually the core of the fingerprint is aligned
with the line of union of the nail to the finger, so
as a general rule, you should place your finger
so that the end of the nail is aligned with the
center of the sensor.

A B
01
01
02
02
03
GND GND GND PWR
GND DATA1
CLK1
ERR1BZ1
DATA2
CLK2
PWR
DATA3
CLK3
DATA4
CLK4
485+ TXD1
485- RXD1
TXD3
RXD3 OK2 OK1
ERR2BZ2
MRAC
ENEN
Secure the rear plate to the wall using the wall mounting screws. (Use your own
bushings)
Attach the MPXR82MFS and the rear plate using
a star-shaped screw.
BOTTOM VIEW
Mount the MPXR82MFS terminal on the rear plate.
. CONNECTION SCHEME
CONNECTION TO MRAC CONTROL BOARD
12Vdc (Red)
RS485 RXD (Blue)
RS485 TXD
(Yellow)
GND (Black)
1
2
3
MPXR82MFS
For the operation of this player, it is
necessary to register the fingerprint
on the recorder MFM-800.
. INSTALLATION
INSTALLATION OF WALLMOUNT

A B
ENEN
. CONNECTION SCHEME . CONNECTION SCHEME
EXTERNAL POWER CONNECTION
12Vdc (Red)
GND (Black)
Recommended power supply:
• 12Vdc ±10%, at least 500mA;
• Comply with IEC / EN 60950-1 standard;
• To share power with other devices, use a power supply with higher current ratings.
Nº PIN DESCRIPTION WIRE
1 Vdc Red
 GND Black
FA3
ETHERNET CONNECTION
SWITCH
SERVER
TCP/IP TCP/IP
RS485 RXD
(Blue)
RS485 TXD
(Yellow)
MRAC
CONTROL
BOARD
MPXR82MFS
MPXR82MFS

A B
ENEN
01 • Connect the RJ45 cable and power to the reader.
02 • Check that the IP of the reader is in the same IP range as the computer.
03 • Open MOTORLINE IP TOOL software 05 • Connect to the reader by selecting the reader and click "Connect Setup".
04 • Click "Search" to search for the reader.
. DIP SWITCH . DIP SWITCH
DIP SWITCH CONFIGURATION DIP SWITCH CONFIGURATION

A B
ENEN
06 • Write the ID for the reader taking into account your connections to the door.
07 • Click "Set ID", the message "OK" will appear if the IP reset is successful.
Through the software there is no limit to the configuration of IDs, however the maximum
number of readers for use on a board, is  readers.
Numbers Door Direction
 Door  Entry
 Door  Exit
 Door  Entry
 Door  Exit
. COMPONENT TEST
DEVICE TEST
2. Register the fingerprint to the controller.
1. When the power is on, the reader will flash the red LEDs and hear the beep
simultaneously.
3. Place your fingerprint on the reader and the green LED will light up after successful
verification and identification.
Red LED Green LED
. DIP SWITCH
DIP SWITCH CONFIGURATION

 EN
PROBLEM SOLUTION
The fingerprint cannot be read or takes too long. . Check that your finger or fingerprint sensor is stained with sweat, water, or dust. . Try again after cleaning your finger and fingerprint sensor with dry paper or a slightly damp cloth.
. If the fingerprint is too dry, scare your finger and try again.
The fingerprint is checked, but the authorization continues to fail. 1. Make sure the user is restricted by zone or time zone. 2. Check with your administrator to see if the registered fingerprint was deleted from the device for some
reason.
Authorized access, but the door does not open. 1. Make sure that the lock duration is set to the appropriate minutes, which opens the lock. 2. Make sure the anti-passback mode is in use. In anti-passback mode, only the person who entered
through that door can exit.
The device alarm is ringing. 1. Make sure the device and the rear plate are well connected to each other. If not, an case button is
activated, which triggers the alarm and keeps it active.
How to configure the MPXR82MFS used as a fingerprint reader in the Inbio access controller. 1. Please contact our technical support department.
. TROUBLESHOOTING
INSTRUCTIONS FOR FINAL CONSUMERS / SPECIALIZED INSTALLERS