Motorline Mc75 Use and care manual

SEL SET

L AB FE LAMP OP CL LECOMN

CL CE

V +

PHOTO

P.MAN

TIME.M

CMD.L

CMD

TIME.P

v. REV. /

MC75

HW: MC_V.

FW: MC_V.

MC75 EN

USER’S AND INSTALLER’S MANUAL

1A 1B

ENEN

This product is certified in accordance with European Community

(EC) safety standards.

This product complies with Directive 2011/65/EU of the European

Parliament and of the Council, of 8 June 2011, on the restriction

of the use of certain hazardous substances in electrical and

electronic equipment and with Delegated Directive (EU) 2015/863

from Commission.

(Applicable in countries with recycling systems). This marking on

the product or literature indicates that the product and electronic

accessories (eg. Charger, USB cable, electronic material, controls,

etc.) should not be disposed of as other household waste at the

end of its useful life. To avoid possible harm to the environment

or human health resulting from the uncontrolled disposal

of waste, separate these items from other types of waste and

recycle them responsibly to promote the sustainable reuse

of material resources. Home users should contact the dealer

where they purchased this product or the National Environment

Agency for details on where and how they can take these items

for environmentally safe recycling. Business users should contact

their vendor and check the terms and conditions of the purchase

agreement. This product and its electronic accessories should

not be mixed with other commercial waste.

This marking indicates that batteries should not be discarded like

other household waste at the end of their useful life. Batteries

must be delivered to selective collection points for recycling.

The different types of packaging (cardboard, plastic, etc.) must be

subject to selective collection for recycling. Separate packaging

and recycle it responsibly.

This marking indicates that the product and electronic accessories

(eg. charger, USB cable, electronic material, controls, etc.) are

susceptible to electric shock by direct or indirect contact with

electricity. Be cautious when handling the product and observe

all safety procedures in this manual.

00. CONTENT 01. SAFETY INSTRUCTIONS

INDEX

STANDARDS TO FOLLOW

BUTTON REMOTE CONTROL

LEDS

BUTTON REMOTE CONTROL

REMOTE CONTROL FOR EXTERNAL LAMP CONTROL

PROGRAMMING OF REMOTE CONTROL

PROGRAMMING EXTERNAL LAMP REMOTE CONTROLS REMOTELY

DELETE ALL THE REMOTE CONTROLS

CONNECTING COMPONENTS TO THE CONTROL BOARD

TECHNICAL CHARACTERISTICS

INFORMATION LEDS

CONNECTION CONNECTORS

. SAFETY INSTRUCTIONS

. THE CONTROL BOARD

. CONNECTIONS SCHEME

. MAIN MENU

MOTORS WORKING TIME

EXTENDED MENU 

INSTRUCTIONS FOR FINAL CONSUMERS

INSTRUCTIONS FOR SPECIALIZED INSTALLERS

HUMAN PRESENCE FUNCTION

EXTENDED MENU 

. EXTENDED MENU

. TROUBLESHOOTING

USE OF PHOTOCELLS

PAUSE TIME PROGRAMMING

TOTAL RESET

EXTENDED MENU 

EXTENDED MENU 

2A 2B

ENEN

• Children shouldn’t play with the product or opening devices to

avoid the motorized door or gate from being triggered involuntarily.

• If the power cable is damaged, it must be replaced by the

manufacturer, after-sales service or similarly qualified personnel

to avoid danger.

•The device must be disconnected from the electrical network when

removing the battery.

• Ensure that blocking is avoided between the actuated part and its

fixed parts due to the opening movement of the actuated part.

WARNINGS FOR TECHNICIANS

• Before beginning the installation procedures, make sure that you

have all the devices and materials necessary to complete the

installation of the product.

•You should note your Protection Index (IP) and operating temperature

to ensure that is suitable for the installation site.

• Provide the manual of the product to the user and let them know

how to handle it in an emergency.

• If the automatism is installed on a gate with a pedestrian door, a

door locking mechanism must be installed while the gate is in motion.

• Do not install the product “upside down” or supported by elements

do not support its weight. If necessary, add brackets at strategic

points to ensure the safety of the automatism.

• Do not install the product in explosive site.

• Safety devices must protect the possible crushing, cutting, transport

and danger areas of the motorized door or gate.

• Verify that the elements to be automated (gates, door, windows,

blinds, etc.) are in perfect function, aligned and level. Also verify if

the necessary mechanical stops are in the appropriate places.

•The control board must be installed on a safe place of any fluid

(rain, moisture, etc.), dust and pests.

•You must route the various electrical cables through protective

tubes, to protect them against mechanical exertions, essentially on

GENERAL WARNINGS

•This manual contains very important safety and usage information.

Read all instructions carefully before beginning the installation/

usage procedures and keep this manual in a safe place that it can

be consulted whenever necessary.

•This product is intended for use only as described in this manual.

Any other enforcement or operation that is not mentioned is

expressly prohibited, as it may damage the product and put people

at risk causing serious injuries.

•This manual is intended firstly for specialized technicians, and does

not invalidate the user’s responsibility to read the “User Norms”

section in order to ensure the correct functioning of the product.

•The installation and repair of this product may be done by qualified

and specialized technicians, to assure every procedure are carried

out in accordance with applicable rules and norms. Nonprofessional

and inexperienced users are expressly prohibited of taking any

action, unless explicitly requested by specialized technicians to do

so.

• Installations must be frequently inspected for unbalance and the

wear signals of the cables, springs, hinges, wheels, supports and

other mechanical assembly parts.

• Do not use the product if it is necessary repair or adjustment is

required.

• When performing maintenance, cleaning and replacement of

parts, the product must be disconnected from power supply. Also

including any operation that requires opening the product cover.

•The use, cleaning and maintenance of this product may be carried

out by any persons aged eight years old and over and persons

whose physical, sensorial or mental capacities are lower, or by

persons without any knowledge of the product, provided that

these are supervision and instructions given by persons with

experienced in terms of usage of the product in a safe manner and

who understands the risks and dangers involved.

01. SAFETY INSTRUCTIONS 01. SAFETY INSTRUCTIONS

3A 3B

ENEN

the power supply cable. Please note that all the cables must enter

the control board from the bottom.

• If the automatism is to be installed at a height of more than 2,5m

from the ground or other level of access, the minimum safety and

health requirements for the use of work equipment workers at the

work of Directive 2009/104/CE of European Parliament and of the

Council of 16 September 2009.

• Attach the permanent label for the manual release as close as

possible to the release mechanism.

• Disconnect means, such as a switch or circuit breaker on the

electrical panel, must be provided on the product’s fixed power

supply leads in accordance with the installation rules.

• If the product to be installed requires power supply of 230Vac or

110Vac, ensure that connection is to an electrical panel with ground

connection.

•The product is only powered by low voltage satefy with control

board (only at 24V motors).

• Parts/products weighing more than 20 kg must be handled with

special care due to the risk of injury. It is recommended to use

suitable auxiliary systems for moving or lifting heavy objects.

• Pay special attention to the danger of falling objects or uncontrolled

movement of doors/gates during the installation or operation of

this product.

WARNINGS FOR USERS

• Keep this manual in a safe place to be consulted whenever necessary.

• If the product has contact with fluids without being prepared, it

must immediately disconnect from the power supply to avoid short

circuits, and consult a specialized technician.

• Ensure that technician has provided you the product manual and

informed you how to handle the product in an emergency.

• If the system requires any repair or modification, unlock the

automatism, turn off the power and do not use it until all safety

MOTORLINE ELECTROCELOS SA.

Travessa do Sobreiro, nº29

4755-474 Rio Côvo (Santa Eugénia)

Barcelos, Portugal

SYMBOLS LEGEND:

• Important safety notices

• Useful information

• Programming information

• Potentiometer

information

• Connectors

information

• Buttons information

conditions have been met.

• In the event of tripping of circuits breakers of fuse failure, locate

the malfunction and solve it before resetting the circuit breaker or

replacing the fuse. If the malfunction is not repairable by consult

this manual, contact a technician.

• Keep the operation area of the motorized gate free while the gate

in in motion, and do not create strength to the gate movement.

• Do not perform any operation on mechanical elements or hinges if

the product is in motion.

RESPONSABILITY

• Supplier disclaims any liability if:

•Product failure or deformation result from improper installation

use or maintenance!

• Safety norms are not followed in the installation, use and

maintenance of the product.

• Instructions in this manual are not followed.

• Damaged is caused by unauthorized modifications

• In these cases, the warranty is voided.

01. SAFETY INSTRUCTIONS 01. SAFETY INSTRUCTIONS

SEL SET

PHOTO

P.MAN

TIME.M

CMD.L

CMD

TIME.P

LAB FE LAMP V + OP CL LECOM

CL LE

321 4 5 6 7 8 9 10 11 12 13 14 15

230v

110v

DV NC12/24V DV 12/24VCOM

MOTOR

~ ~ ~ ~

230~

LAb

V + OP CL LE

Com

230~

Cl Ce

1 2 3 4 5 6 7

10 11 12 13 14 15

230~

LAb

V + OP CL LE

Com

230~

Cl Ce

1 2 3 4 5 6

10 11 12 13 14 15

TUB | ROLLING

4EN

02. CONNECTIONS SCHEME

CONNECTING COMPONENTS TO THE CONTROL BOARD

Shunt

 Button remote control

- Step by Step Operation

You must put a bridge

(shunt) between Op and Cl,

connecting the control board

between the OP and the COM

 Buttons remote control

-  button for opening and ano-

ther one for closing

Photocells set

Antenna

Flashing lamp

5A 5B

L AB FE LAMP OP CL LECOMN

CL CE

V +

321 4 5 6 7 8 9 10 11 12 13 14 15

OP CL LE

ENEN

The MC is a control board developed speciﬁcally for rolling motors (TUB and ROLLING range), which

allows the programming of working time and pause time for automatic closing..

It has the ability to detect limit switch devices and when the motor is locked, and as such, the working

time ends as soon as the curtain or rolling grilles reaches a limit switch and when it detects that the

motor is locked (in eort).

V V

• Power Supply Vac /Hz Vac /Hz

• Motor output power W max W max

• Remote controls  Bits or Rolling Code

• Maximum memory capacity  Codes

• Working temperature -°C  °C

• Built-in radio receiver , Mhz

• Auxiliary accessory output Vdc/mA

• External lamp output W W

• Motor output fuse Øxmm Ah Øxmm Ah

Low voltage fuse for accessories output Øxmm mA

03. THE CONTROL BOARD 03. THE CONTROL BOARD

THECNICAL CHARACTERISTICS

LED DESCRIPTION

OP Opening order Receiving signal No activity signal

CL Closing order Receiving signal No activity signal

LE Indication of the photocell Circuit Button Detected photocells Photocells not detected

CONNECTION CONNECTORS

INFORMATION LEDS

1• Ground connection

2• Ground connection

3• 230V/110V Power Supply - Phase (L) Control board power supply connection

4• 230V/110V Power Supply – Neutral (N)

5• Motor output – Opening (AB) Connection of the opening and closing phases of the

motor. If the direction of the motor is contrary to the

intended direction, simply replace the two wires to

reverse the direction.

6• Motor output - Neutral (COM)

7• Motor output – Closing (FE)

8• External Lamp output - Phase Connection for external lamp with maximum output

duration of  min.

9• External Lamp output - Neutral

10 • Common (COM) Device power output

11 • Vdc Ma Auxiliary output (V)

12 • NO input for push button - Opening (OP) Circuit for connection of push button:

Two button push button: Opening and closing control

on each button.

One button push button: Operates in Step-by-step mode

(open-stop-close-stop -...) always with the same button.

To do this, you must put a shunt between Op and Cl, by

connecting the push button between Op and COM.

13 • Common (COM)

14 • NO input for push button - Closing (CL)

15 • NC input for Photocells (LE)

[Complete circuit with COM (11 or 13)]

This circuit allows the connection of all types of safety

photocells.

This device only intervenes in closing and pause opera-

tions, as follows:

- In closing, stops and starts the complete opening of the

automation

- In pause time, it prevents the automation from starting

the closing by holding it open.

6A 6B

SEL SET

AB FE LAMP OP CL LECOMN

CL CE

V +

PHOTO

P.MAN

TIME.M

CMD.L

CMD

TIME.P

ENEN

04. MAIN MENU 04. MAIN MENU

2BUTTON REMOTE CONTROL

Functionality - This function allows you to memorize a 2-button remote control via the con-

trol board.

Memorizing a 2-button remote control (normal operation):

 • Press the SEL button as many times as necessary until the CMD LED starts blinking.

 • Press the remote control button for closing for  second. The CMD LED ﬂashes at twice

the initial speed, signaling the button recording.

 • Press a remote control button for opening for  second. The CMD LED stops blinking,

signaling the button recording, and the CMD.L LED ﬂashes.

Wait for  seconds, the control board exits of programming mode and all LEDs stop blinking.

Remote control(s) programmed No programmed remote controls

Functionality - This function allows you to memorize a 1-button remote control via the control

board.

Memorizing a 1-button remote control (Step by Step operation):

 • Press the SEL button as many times as necessary until the CMD LED starts blinking.

 • Press the remote control closing button for  second. The CMD LED ﬂashes at twice the

initial speed, signaling the button recording.

 • The remote control is memorized. Wait for  seconds, the control board exits the

programming mode and all LEDs stop blinking.

LEDs Main menu: The control board has a set of LEDs that allows to identify the status of

the dierent functions.

1BUTTON REMOTE CONTROLLEDs

Remote control(s) programmed No programmed remote controls

REMOTE CONTROL FOR EXTERNAL LAMP CONTROL

PROGRAMMING OF REMOTE CONTROLS

Functionality - This function allows you to memorize a remote control to control the external

lamp through the control board.

Memorize a remote control to control the external lamp:

 • Press the SEL button as many times as necessary until the CMD.L LED starts blinking.

 • Press the remote control button to control the lamp output for  second.

 • The remote control is memorized.

Wait for  seconds, the control board exits the programming mode and all LEDs stop blinking.

Remote control(s) programmed No programmed remote controls

Functionality - This function allows you to program new remote controls via an already conﬁ-

gured remote control.

Programming remote controls for opening/closing:

 • With the rolling grilles fully open/closed, press the open/close button of a remote

control already programmed for a time superior to  seconds. When the lamp blinks twice,

the control board has entered on programming mode remotely.

 • Push the closing button of the new remote control for  second. The lamp blinks once.

 • Press the button of a new remote control for opening for  second. The lamp blinks twice

and the remote control is programmed.

Remote control(s) programmed No programmed remote controls

LED DESCRIPTION

TIME P Pause time Programmed Not Programmed

PHOTO Enable Photocells Active Disabled

P. MAN Human presence Active Disabled

TIME. M Working time Active Disabled

CMD. L. Lamp remote control Programmed remote control (s) No program. remote controls

CMD Remote control Programmed remote control (s) No program. remote controls

7A 7B

ENEN

Function on Function o

04. MAIN MENU 04. MAIN MENU

Functionality - This function allows you to set the opening and closing time of the motor.

 • Close the rolling grilles manually.

 • Press the SEL button as many times as necessary until the TIME.M LED starts ﬂashing.

 • Press the SET button continuously for the time required for the opening operation. When

you reach the end of the opening, release the SET button to end programming. If you have

activated the "Detection of Limit Switch" option, this programming will end automatically

when the control board detects the limit switch.

Wait for  seconds, the control board exits the programming mode and all LEDs stop

ﬂashing.

Functionality - This function allows you to activate the Human presence function. When enabled,

the automation only closes as long as the closing button is pressed

 • Press the SEL button as many times as necessary until the P.MAN LED blinks.

 • Press the SET button to enable/disable the option.

Wait for  seconds, the control board exits the programming mode and all LEDs stop blinking.

Functionality - This function allows you to activate/deactivate the use of the Photocells, to

reverse and prevent the closing of the automation when the signal is interrupted

 • Press the SEL button as many times as necessary until the LED PHOTO blinks.

 • Press the SET button to enable/disable the option.

Wait for  seconds, the control board exits the programming mode and all LEDs stop blinking.

PROGRAMMING EXTERNAL LAMP REMOTE CONTROLS REMOTELY

MOTORS WORKING TIME

HUMAN PRESENCE FUNCTION

TOTAL RESET

PAUSE TIME PROGRAMMING

Function on

Function o

USE OF PHOTOCELLS

If you do not connect photocells to the control board, you must deactivate

this function.

Functionality - This function allows you to set the time the automation waits ater opening until

the automatic closing is started.

 • Press the SEL button as many times as necessary until the TIME.P LED starts blinking.

 • Press the SET button to start counting time (the LED ﬂashes at twice the initial speed), and

press again the SET button to end the pause time count.

Functionality - This function allows you to restore all the factory settings and all the memorized

remote controls will be erased

 • Press the SEL and SET buttons at the same time for  seconds. The LEDs turn on and o,

signaling that the operation has been done.

Functionality - This function allows you to memorize the remote control to control the external

lamp via an already conﬁgured remote control.

Remote Control programming for external lamp control:

 • Press the lamp button of an already programmed remote control for more than 

seconds. When the lamp blinks twice, it has entered on programming mode remotely.

 • Press the button on the new remote control to control the lamp.

The lamp blinks twice and the remote control is programmed.

Remote control(s) programmed No programmed remote controls

Functionality - This function allows you to delete all remote controls added to the control board.

 • Press the SEL button as many times as necessary until the CMD LED blinks.

 • Press the SET button once and the CMD LED goes o signaling the elimination of all the

remote controls.

DELETE ALL THE REMOTE CONTROLS

Remote control(s) programmed No programmed remote controls

8A 8B

ENEN

05. EXTENDED MENU 05. EXTENDED MENU

EXTENDED MENU 2 - Programming of remote controls

EXTENDED MENU 3 - Type of motor connected to the control board

Functionality - This menu allows you to activate or deactivate the possibility of programming new remote

controls through an already conﬁgured remote control.

The control board is supplied with this PGN function enabled

01 • Access Extended Menu 1 (consult instructions from the previous menu).

02 • Within the Extended Menu 1, press the SET button for more than 5 seconds. The TIME.M and P.MAN

LEDs ﬂash simultaneously.

03 • Press the SEL button to turn on/o the CMD LED by choosing the desired option!

04 • Press the SET button to save the selected option.

The control board will automatically exit programming mode.

Functionality - This menu allows you to choose the type of motor connected to the control board for

eort inversion functions(motor locked).

The control board is supplied with 17RPM Motor mode enabled.

To access the Extended Menu 3 options follow the steps:

01 • Access Extended Menu 2 (consult instructions from the previous menu).

02 • Within the Extended Menu 2, press the SET button for more than 5 seconds. The TIME.M and P.MAN

LEDs ﬂash alternately quickly.

03 • Press the SEL button to turn ON/OFF the CMD LED by choosing the desired option!

04 • Press the SET button to save the selected option.

The control board will automatically exit programming mode.

EXTENDED MENU 2

LED LED OFF LED ON

• CMD Remote programming = ON Remote programming = OFF

• P.MAN Flashing ON/OFF

• TIME.M Flashing ON/OFF

EXTENDED MENU 3

LED LED OFF LED ON

• CMD 12RPM Motor 17RPM Motor

• P.MAN Flashing ON/OFF

• TIME.M Flashing OFF/ON

EXTENDED MENU 1 - LAMP/CORT - Output control for Lamp

Functionality - This menu allows you to set the type of external lamp operation. The control board is

supplied by default with the lamp control via the remote control.

To access the Extended Menu 1 options follow the steps:

01 • Press the SET button for more than 5 seconds. The TIME.M and P.MAN LEDs ﬂash alternately.

02 • Press the SEL button to pass through the various operating modes.

03 • Press the SET button to save the selected option.

The control board will automatically exit programming mode.

EXTENDED MENU 1

Operation LED CMD LED CMD.L

• Control by remote control Deleted Deleted

• Lamp lights up when opening

and closing On Deleted

• Lamp lights up when opening,

closing, and pause time (when

active) Deleted On

• Lamp lights up when opening,

closing, during pause time and

stays on for three minutes ater

closing

On On

• P.MAN Flashing ON/OFF

• TIME.M Flashing OFF/ON

EXTENDED MENU 4

LED LED o LED on

• CMD Disable detection Enable detection

• PHOTO Flashing ON/OFF

• TIME.P Flashing ON/OFF

Functionality - This menu allows you to set the sensitivity levels for the locked motor detection. The

control board is supplied at the factory with level 0 (detection disabled), and this value can be adjusted,

ranging from 1 to 5 (1 less sensitive and 5 more sensitive).

To access the Extended Menu 4options, follow the instructions below:

01 • Access Extension Menu 3 (see instructions in the previous menu).

02 • Within the Extended Menu 3, press the SET button for more than 5 seconds. The LED TIME.P and

PHOTO will ﬂash rapidly alternately.

03 • Press the SEL button as many times as necessary to change the values. The LEDs will light sequentially.

EXTENDED MENU 4 - Blocked motor detection

Level LEDs

1CMD

2CMD CMD.L

3CMD CMD.L TIME.M

4CMD CMD.L TIME.M P.MAN

9EN

. TROUBLESHOOTING

INSTRUCTIONS FOR FINAL CONSUMERS INSTRUCTIONS FOR SPECIALIZED INSTALLERS

Anomaly Procedure Behavior Procedure II Discovering the origin of the problem

• Motor

doesn’t

work

• Make sure you

have 110/230V

power supply

connected to

automation and

if it is working

properly.

• Still not working • Consult a qualiﬁed

MOTORLINE technician.

1 • Open control board and check if it has 110/230V power supply;

2 • Check the control board input fuses;

3 • Disconnect the motor from control board and test it by connecting directly to 230Vdc power supply in order to find out if they

have problems.

4 • If the motor works, the problem is on the control board. Pull it out and send it to the MOTORLINE technical services for

diagnosis;

5 • If the motor doesn’t work, remove it from installation site and send to the MOTORLINE technical services for diagnosis.

• Motor

doesn’t

move but

makes noise

• Unlock motor

and move the

rolling grilles by

hand to check

for mechanical

problems on the

movement.

• Encountered

problems? • Consult a qualiﬁed

MOTORLINE technician.  • Check all motion axis and associated motion systems related with the rolling grilles and the automatism (bolts, hinges, etc.)

to ﬁnd out what is the problem.

• The rolling

grilles moves

easily?

• Consult a qualiﬁed

MOTORLINE technician.  • If the motor works, the problem is on the control board. Pull it out and send it to the technical services for diagnosis;

• If the motor doesn’t work, remove it from installation site and send to the technical services for diagnosis.

• Motor

opens, but

doesn’t

• Unlock motor and

move the rolling

grilles by hand to

closed position.

Lock motor again

and turn off

power supply

for 5 seconds.

Reconnect it and

send order to open

rolling grilles using

remote control.

• Rolling grilles

opened but didn’t

close again.

1 • Check if there is any

obstacle in front of the

photocells;

 • Check if any of the

control devices (key

selector, push button,

video intercom, etc.) of

the rolling grilles are

jammed and sending

permanent signal to

control unit;

 • Consult a qualiﬁed

MOTORLINE technician.

All control boards MOTORLINE have LEDs that easily allow to conclude which devices are with anomalies. All safety devices LEDs

(DS) in normal situations remain On. All "START" circuits LEDs in normal situations remain O.

If LEDs devices are not all On, there is some security systems malfunction (photocells, safety edges). If "START" circuits LEDs are

turn On, there is a control device sending permanent signal.

A) SECURITY SYSTEMS:

 • Close the photocell circuit with shunt or disable the PHOTO function.

 • Check if the system is functional.

 • Replace this device with a functional one, and verify if the automation functions correctly with all other devices. If you ﬁnd any

other faults, follow the same steps until you discover all the problems.

B) START SYSTEMS:

 • Disconnect all wires connected to the connector (PULL and PED).

 • If the LED turned O, try reconnecting one device at a time until you ﬁnd the defective device.

NOTE:

In case procedures described in sections A) and B) don’t result, remove control board and send to the technical services for

diagnosis.

• Motor

doesn’t

make com-

plete route

Unlock motor and

move rolling grilles

by hand to check

for mechanical

problems on the

rolling grilles.

• Encountered

problems? • Consult an experienced

rolling grilles expert.  • Check all motion axis and associated motion systems related with the rolling grilles and the automatism (bolts, hinges, etc.)

to ﬁnd out what is the problem.

• The rolling

grilles moves

easily?

• Consult a qualiﬁed

MOTORLINE technician.