Motorola H500 Parts list manual

Feature and Function Guide of Bluetooth Neckloop
Charge Port
Volume Buttons
Call Button
Neckloop
Blue Indicator Light
Microphone
Get Connected in 4
Q
uick Ste
p
s
1. Char
g
e Batter
y
2. Start Bluetooth on Cell
p
hone
3. Pair Bluetooth and Cell
p
hone
4. Test and Use
1. Charge Bluetooth Battery for 2 Hours
A. Plug AC power charge into the end of bleutooth
The bluetooth indicator light turns on when the battery is charging
It may take up to 1 minute for the light to turn on.
When full charged (about 2 hours), the light will turns off.
B. Unplug the AC power adaptor
Note: Bluetooth is not funtional while charging. Charge from PC is applicable.
2. Start Bleutooth Feature on Your Phone
Your cellphone's Bluetooth feature is off by default. To use bluetooth neckloop, turn on the Bluetooth feature.
For most Motorola cell phones:
A. Select Menu > Settings > Connections > Bluetooth Link > Setup.
B. Scroll to Power
C. Press Change
D. Scroll to On
E. Press Select to turn on the Bluetooth feature. Bluetooth feature remains on unitl you turn it off.
Note: These steps are for most Motorola cell phones. For other phones, see your phone's user's guide.
3. Pair Bluetooth and Cellphone
Before use neckloop, must pair it with your phone.
A. Put Bluetooth in paring mode
i. With the bluetooth power off, press and hold the call button for 6 to 10 seconds until the blue indicator light
turns on and remains steadily it. (The light will flash while you hold the call button)
ii. If the indicator light is flashing or does not remain steadily lit, turn off the bleutooth and repeat step i.
B. The phone to look for bluetooth (for most Motorola phones:)
i. Select Menu > Settings > Connection > Bluetooth Link > Handsfree > Look for Devices.
The phone lists all Bluetooth devices it finds.
ii. Select Motorola H500.
iii. Press OK or Yes to pair the bluetooth.
iv. Enter the password 0000 and press OK.
While bluetooth is successfully paired with your phone, the indicator changes from steadily lit to flashing.
Note: These steps are for most Motorola cell phones. For other phones, see your phone's user's guide.
Ph
y
sical Produc
t
Illuminate

4. Test and Use
Your phone and headset are now paired and ready to make and receive
calls after wear it in your neck. Make a call to test:
A. Wear the neckloop as right side photo showing.
B. Load battery and put earpiece in ear canal.
C. On your phone, dial the number you want to call.
D. If your phone and headset are successfully paired
you will hear voice after connected with the dialed number.
After you have successfully paired your phone and bluetooth,
you need not to repeat these initial steps each time you use bluetooth.
Troubleshooting
My phone does not find my bluetooth.
Make sure the blue light on your headset is steadily lit when your phone is searching for devices (see step 3)
My bluetooth worked before but now it's not working.
Make sure your phone is on and bluetooth feature is turned on (see step 2).
If you have confirm bluetooth feature is on in your phone, pair your phone and bluetooth again (see step 3)
Turn On and Off
To turn your bluetooth on, press and hold the call button until the indicator light flashes. Then release button.
To turn your bluetooth off, press and hold the call button until the indicator light flashes rapidly and then turns off.
Note: To conserve battery power, turn off your bluetooth when you don't lan to use it for a while.
Making Calls
Function Action
Make a voice dial call Tap the call button and speak the name after the tone
End a call Tap the call button
Receive a call Tap the call button
Reject a call Press and hole the call button until you hear a beep
Redial last call Press and hole the call button until you hear a beep
Answer a second incoming call Press and hold the call button (places first call on hold)
Toggle etween two active calls Press and hold the call button
Join a 3-way call (Feature is phone/network dependent) Press and hold both volume buttons
Put an active call on hold or resume a call on hold Press and hole the call button until you hear a beep
Transfer a call from the phone to bluetooth Tap the call button
Disable or enable the indicator light Press and hold both Volume buttons for 3~4 seconds
Mute or unmute a call Tap both volume buttons
Indicator Lights Audio Tones
Indicator Status Status Audio Tone Status
(With charger plugged in) Single high tone when Volume at minimum
On (steady) Charging pressing volume button or maximum
Off Charging complete Five rapid high tones Low battery
(Without charger plugged in) repeated every 60 sec
Off Power off Ring tone Incoming call
On (steady) Pairing mode Single high tone Pairing confirmation
10 rapid flashes Pairing successful Single low tone Voice activation
Slow pluse Connected Dual high/low tone Voice tag not
Quick flash Standby recognized
Single high tone End call
Note: After 5 minutes of inactivity, the light stops Low to hight tone Phone network not
flashing to conserve power, but the bluetooth available
remains in standby mode. Two ascednding tones Mute enabled
Two descending tones Mute enabled