Motorola MBP10S User manual

User’s Guide
Digital Baby Monitor
Model: MBP10S
The features described in this user’s guide are subject to modifications without prior notice.

Welcome...
to your new Motorola Digital Baby Monitor!
Thank you for purchasing the MBP10S. This baby monitor uses digital
communication which ensures that you can hear your baby clearly without
any distracting noise or interference.
Please retain your original dated sales receipt for your records. For warranty
service of your Motorola product, you will need to provide a copy of your
dated sales receipt to confirm warranty status. Registration is not required
for warranty coverage.
For product related questions, please call:
This User’s Guide provides you with all the information you need to get the
most from your product.
Before you can use the baby monitor, you’ll need to insert and fully charge
the battery on the Parent unit. Please read the Safety Instructions in section
1 "Safety Instructions" before you install the units.
Got everything?
• 1 x Parent unit
• 1 x Baby unit
• 1 x Rechargeable battery pack for the Parent unit
• 1 x Power adapter for the Parent unit
• 1 x Power adapter for the Baby unit
[phone] (UK only)*
*Calls cost 7ppm + your phone company's access charge.
[phone] (ROI)
On the Web: www.motorolahome.com/support

Overview of your Parent unit
1. Link indicator LED
2. Volume down button -
3. Power On/Off button
4. Speaker
5. Volume up button +
6. Power (ON/ ) LED
7. Volume Indicator LEDs
8. Power adapter connector
9. Belt clip
10. Battery cover screw
11. Battery cover
1
2
3
4
5
6
7
8
9
10
11
Overview of your Baby unit
12 Power LED
13. Microphone
14. FIND key
15. Power adapter connector
FIND
13
14
15
12

4
Table of contents
1. Safety Instructions.................................................................................... 5
2. Getting Started......................................................................................... 7
2.1 Baby unit power supply ...................................................................... 7
2.2 Parent unit battery installation ............................................................ 7
2.3 Parent unit power supply ....................................................................9
2.4 Link ....................................................................................................10
2.5 Paging ............................................................................................... 10
3. Using the MBP10S .................................................................................. 11
3.1 Volume adjustment on the Parent unit............................................. 11
4. Disposal of the Device (environment) ................................................... 12
5. Cleaning ................................................................................................. 12
6. Help ......................................................................................................... 13
7. General Information ............................................................................... 14
8. Technical Specifications ....................................................................... 19

Safety Instructions 5
ENGLISH
1. Safety Instructions
WARNING:
Strangulation Hazard. Children
have STRANGLED in cords.
Keep this cord out of the reach
of children (more than 1m
away). Never use extension
cords with AC Adapters. Only
use the AC Adapters provided
.

6Safety Instructions
This baby monitor is compliant with all relevant standards regarding
electromagnetic fields and is, when handled as described in the User’s Guide,
safe to use. Therefore, always read the instructions in this User’s Guide carefully
before using the device.
• Adult assembly is required. Keep small parts away from children when
assembling.
• This product is not a toy. Do not allow children to play with it.
• This baby monitor is not a substitute for responsible adult supervision.
• Keep this User’s Guide for future reference.
• Do not place the baby unit or cables in the crib or within arm’s reach of the baby
(the unit should be at 1 metre away).
• Keep the cords out of reach of children.
• Do not cover the baby monitor with a towel or blanket.
• Never use extension cords with power adapters. Only use the power adapters
provided.
• Test the baby monitor before use. Become familiar with its functions.
• Do not use the baby monitor near water.
• Do not install the baby monitor near a heat source.
• Only use the chargers and power adapters provided. Do not use other chargers
or power adapters as this may damage the device and batteries.
• Only insert batteries of the same type. Never use ordinary, non-rechargeable
batteries in the parent unit. Insert batteries with the right polarity (indicated in the
battery compartment).
• Do not touch the charger or plug contacts with sharp or metal objects.
CAUTION
Risk of explosion if battery is replaced by an incorrect type. Dispose of used
batteries according to the instructions.

Getting Started 7
ENGLISH
2. Getting Started
2.1 Baby unit power supply
1. Connect the small plug of the power adapter to the power connector on
the baby unit and the other end of the adapter to a mains power socket
(100-240Vac~50/60Hz).
NOTE
Only use the enclosed power adapter (5V DC /600mA).
2.2 Parent unit battery installation
Black
Red

8Getting Started
The Parent unit can be used with either the rechargeable battery pack (2.4V
600mAh Ni-MH rechargeable battery pack supplied) or via the power adapter
supplied.
WARNING:
Never use ordinary, non-rechargeable batteries. The power outlet adapter
provides a charging function, and non-rechargeable batteries may explode
and cause damage!
NOTE
The Ni-MH rechargeable batteries must be charged for 16 hours before using
the Parent unit without the power outlet.
We recommend the rechargeable batteries are installed, so that the unit
continues to work in the event of a power failure.
1. Using a screwdriver, turn the screw of the battery cover on the back of the
parent unit 90 degrees in a counterclockwise direction. Remove the
battery cover.
NOTE
Rotate the belt clip to its hanging position to make it easier to access the battery
compartment.
Do not try to turn the screw further beyond the OPEN position marked on the
cover.
2. Insert one battery pack with 2 AAA size Ni-MH rechargeable batteries.
3. Close the battery compartment and turn the screw back 90 degrees back
in a clockwise direction.
4. Press and hold . The Power (ON / ) LED will illuminate red if it only
has battery power.
5. Press and hold to switch off the parent unit.

Getting Started 9
ENGLISH
NOTE
When the battery level is low, the green power LED will flash and the parent unit
will emit a warning beep once every minute. If the baby unit loses power or goes
out of range, the link will be lost and the parent unit will emit a warning beep
every 20 seconds and the green link LED on the Parent unit will continue to flash.
WARNING
Do not mix old batteries with new ones.
Keep batteries away from small children.
Do not short-circuit batteries or dispose of in fire.
Remove the batteries if this device is not going to be used for a long period of
time.
2.3 Parent unit power supply
1. Connect the small plug of the power adapter to the power connector on
the parent unit and the other end of the adapter to the mains power socket
(100V-240V ~ 50/ 60Hz).
NOTE
Only use the enclosed adapter (5V DC/600mA).
2. Press and hold . The Power (ON / ) LED will illuminate red when it is
connected to power supply.
3. Press and hold to switch off the parent unit.

10 Getting Started
2.4 Link
NOTE
Do not place the Baby unit or cables in the crib or within arm’s reach of the baby
(the unit should be at least 1 metre away).
When using the baby monitor for the first time, it is advised to test the
connection.
• Install the parent unit in the same room as the baby unit, but make sure there
is at least 1 metre between the 2 units.
• When both units are switched on, the parent unit will search for the baby
unit.
• The green link LED on the Parent unit will flash until the parent unit is
connected with the Baby unit. Once the link is established, the LED will stop
flashing.
• The sound captured by the microphone on the Baby unit will be audible on
the parent unit.
• The detected sound level is indicated by the LEDs on the front of the Parent
unit.
• When the connection is established, move the Parent unit to the room you
want to monitor from, but within the operational range.
• When there is no connection or the unit is out of range, the Parent unit emits
a warning beep every 20 seconds and the green link LED on the Parent unit
will flash.
• Move the Parent unit closer until the link is re-established.
2.5 Paging
If the parent unit is misplaced, press the key on Baby unit. The Parent unit will
emit a repeated beep tone for 30 seconds so that you can locate it.
Press any key on the Parent unit, or the again on the Baby unit, to stop paging.