Motorola MOTOMING A1200 Instruction and safety manual

Motorola A1200
WAP, MMS and IMAP4 Email Service Setup Guide
All Motorola A1200 purchased from CSL outlets are already programmed with the standard setting of
@1010 or One2Free Zone. Should you wish to make a new setting or lose your original one in any
circumstances, please follow the procedures below. This service allows you to access in Hong Kong
or overseas. When you access the service from overseas, roaming charges will be incurred.
(I) Setup for Standard Local and Overseas WAP services
1. Tap “ ” enter main menu and according to the following step to select “Setup” “Data
Network” Select profile to be edited “ ” “Edit” input the following parameters in
table.
Services GPRS / CSD (local) CSD (Overseas) only
Profile name CSL CSL CSD Overseas
APN hkcsl Leave it blank
User name Leave it blank
Password Leave it blank
Timeout 15 min Off
Primary gateway IP 192.168.59.51
Port 8080
Secondary gateway IP
Leave it blank
GPRS setting
Port 0

(1) Leave it blank
DNS server
(2) Leave it blank
Dial in number 179111 [phone]
Query at Logon

User name Leave it blank
Password Leave it blank
Baud rate 9600
Line type ISDN Modem
CSD Setting
Timeout 5 min

(1) Leave it blank
DNS server
(2) Leave it blank
2. When completed, tap “Save” then “ ” back to main menu. .
3. Tap “ ” “Browser” icon “ ” “Setup” “Profiles” select any one of the profiles
“ ”“Edit” input the following parameters in table.
(1010 customer) @1010 1010 Overseas CSD
Profile name (One2Free customer) One2Free Zone O2F Overseas CSD
(1010 customer) http://wap.hkcsl.com/1010/
Homepage: (One2Free customer) http://wap.hkcsl.com/o2f/
Network link CSL CSL CSD Overseas
4. When complete, tap “Save” “ ” select the profile as default (e.g.: @1010 or One2Free
Zone) “Save” tap “ ” to quit.
Note: For switching the data connection from CSD to GPRS in WAP browsing, the user requires to exit the
WAP browser and re-enters again while GPRS is in coverage.

(II) Setup for Multimedia Messaging Service (MMS)
1. Tap “ ” enter main menu and according to the following step to select “Setup” “Data
Network” Select profile to be edited “ ” “Edit” input the following parameters in
table.
Profile name CSL MMS
APN hkcsl
User name Leave it blank
Password Leave it blank
Timeout 15 min
Primary gateway IP 192.168.59.51
Port 9201
Secondary gateway IP
Leave it blank
GPRS setting
Port 0

(1) Leave it blank
DNS server
(2) Leave it blank
CSD Setting Leave it blank

(1) Leave it blank
DNS server
(2) Leave it blank
2. When completed, tap “Save” then “ ” back to main menu.
3. Tap “ ” “ ” “Service Setup” “Multimedia Message” input the following
parameters in table:
Profile name CSL MMS
MMSC http://192.168.58.171:8002
Max Sending Size 100K
Default Profile
Tap “ “ Tap “ ”
“New” or “Edit”
Network Profile CSL MMS
Tap “Save” recall the profile “CSL MMS” “Set as Default”
Expire After Maximum
Auto Download 
not when roaming 
not if more than 
Show My Number 
Allow Delivery Report 
Blocked Sender(s) Leave it blank
Reject read reply request 
Auto Retry 
4. When complete. Tap “Save” Tap “ ” to Exit

(III) Setup for IMAP4 Email Account
Setting in part I must be created before.
1. Tap “ ” enter main menu and according to following step to select “Email” icon 
“ ” “Mailbox Setup” “New” Tap “Setup Manually” “OK” input the
following parameters in table :
Mailbox
Name Mail@1010
(1010 customer) O2F Email (One2Free customer)
Server mail.csl1010.com mail.one2free.com
Port 25
[e-mail] [e-mail]
Email Where xxxxxxxx is your mobile phone number
Nickname (User define)
Authentication Off
Same as Receive Setup 
Send Setup
Use SSL No
IMAP
Server imap.csl1010.com imap.one2free.com
Port
143
User Name xxxxxxxx (Your mobile phone number)
Password xxxxxx (User define)
Re-enter Password xxxxxx (Same as user define)
Check All Folders

Save Special Folder

Incoming Message Size
Limit 64K
Receive
Setup
Use SSL No
Signature
Setup Add signature to all outgoing massages

Connection
Setup Profile CSL
2. When complete, tap “OK”  “ ”  Tap “Set Default Mailbox” Select the edited profile 
T ap “OK” Tap “ ” to Exit