Motorola V Series User manual

series
personal communicator
User's Guide
Model V100
GSM900/1800 MHz
-1
Quick Reference Card
]Smart Button. Answers, makes, and end calls. Press to go to
Phone Book, and recall a number using Voice ags.
}Located on outside of communicator. Press to answer and end
a call.
&Press to record VoiceNotes, press again to stop recording.
Sending an SMS Message
1. Press ., type your message, press (.
2. Enter the phone number or select the phone number from the
phone book, then follow the prompts given by your
communicator.
3. When the phone number is displayed, press (.
Mobile Internet Session
During a mobile internet session, the functions of the % and (
buttons change. o access an option that is displayed on the bottom
right-hand of your screen, press (. o access an option that is
Motorola V100 Personal Communicator
Quick Reference Card
Control Buttons
,Press and hold to turn on or off.
(Accept and end a call, setting, or option.
)Reject or cancel a call, setting, option, and to return to the
previous screen. In text mode, deletes the previous character.
$Press to enter Quick Access menu.
!Scroll through messages and text, and increase and decrease
volume.
#Press to read a message.
.Press to write a message.
MUsed to enter numbers 0 - 9. Press once for single number,
press twice for multiple numbers. Press twice to stop entering
numbers.
+Press once to capitalise a letter. Press twice for continuous
capitalisation, press twice again to stop capitalisation.
Quick Reference Card
displayed in the bottom middle of the screen, %. When you want
to go to a previous screen, press ).
Making a Call
Note: Use your headset and use ! to adjust the volume.
Press ] to go to Phone Book, or use Voice ags, select the
number, press (.
Note: Press and release ) to remove the last character, press
and hold ) to remove multiple characters.
Ending a Call
Press ( or ).
Receiving a Call
Note: Use your headset and ! to adjust the volume.
Press ( to answer the call.
Note: When communicator is closed or in the holster, press } to
answer a call and to end a call.
SIM Card and Battery Installation
1. Remove the battery cover.
2. Align the SIM card so the notch in the card lines up with the
notch in the recess, insert card.
3. Align the battery contacts with the contacts in the battery
compartment. Press down on the battery until it clicks into
place.
4. Replace the battery cover.
Note: If the SIM card is inserted incorrectly, “Check Card” is
displayed. Remove the SIM card and re-insert it. If the card does
not work, contact your service provider.
Charging your Battery
Charge the battery by inserting the adapter plug into the port on
your communicator and plugging the adapter into a wall outlet.

1
Introduction
1
Introduction
Congratulations! You are now the proud owner of a Motorola V100
Personal Communicator. Your Personal Communicator combines
advanced calling and messaging capabilities in a small compact unit
that is stylish, easy to use, and will look great on you when you wear
it with the holster.
Your Personal Communicator provides cool and exciting ways to keep in contact
with your family, special friends, and your mates. Just review this user guide
carefully and you will be ready to start using your new Personal Communicator.
A detachable Quick Reference Card is included ith this guide.
Personalised Control
You can setup your Personal Communicator to access important messages, phone
numbers, and features quickly. You can even answer calls with the push of a button.
When you are performing routine tasks, your Personal Communicator provides
prompts and messages that assist you with the next task or confirms your selection.
• You can add nine of your most used features in your Quick Access menu so you
can get to them with a couple of presses of a button.
• Voice ags lets you add voice activated commands to call your phone book
entries. You can also add voice commands to select Quick Access options.
2
Introduction
• With voice notes, you can record notes to yourself or record parts of a call.
(Note: use of this feature is subject to varying state, federal, and country laws
regarding privacy of phone conversations.)
• he ] button lets you display your book entries quickly.
• When your Personal Communicator is closed or in the holster, press }, on
the outside of your Personal Communicator, to answer a call quickly and easily.
• With VibraCall® alert, your Personal Communicator vibrates when you get new
messages or calls to avoid disturbing others or when in a noisy environment.
• You can personalise the menus by choosing the features you want readily
available and storing the ones you use less frequently out of sight.
MO OROLA, the Stylised M Logo, and all other trademarks indicated as such
herein are trademarks of Motorola, Inc.
® Reg. U.S. Pat. & m. Off.
All other product or service names are the property of their respective owners.
© 2000, 2001 Motorola, Inc. All rights reserved.
Personal Communications Sector
1500 Gateway Blvd., Boynton Beach, FL 33426-8292
Printed in the EU 02/01
6881036B80-B
Contents
Introduction ......................................1
Safety Information............................7
Getting Started ...............................16
Installing the SIM Card and
Battery........................................16
Control Buttons ............................18
he Display ..................................20
Backlight........................................21
urning On Your V100 Personal
Communicator............................21
Entering Your SIM Card Personal
Identification Number (PIN) ........21
Entering Your Unlock Code...........22
urning Off Your Personal
Communicator............................22
Tips on Using this Guide...............23
he Main Menu.............................23
Menu Navigation...........................23
Entering the Menus.......................23
Getting Around in the Menus ........24
Exiting the Menus.........................24
How to Use the Control Buttons ...25
Prompts and Messages................26
esting Your V100 Personal
Communicator............................26
SMS Messaging .............................27
Sending an SMS Message........... 27
Storing an SMS Message.............28
Receiving and Reading an SMS
Message .................................... 29
Sending Email Messages.............30
Making a Call..................................31
International Phone Calls .............31
Ending a Call................................32
Redialling the Last Number Called
from Standby Mode....................32
Receiving a Call.............................32
In-Call Menu ...................................32
Hold Call.......................................33
Make a New Call ..........................33
urn Mute On or Off......................33
Restrict My Number ......................33
End Active Call..............................34
Reconnect.....................................34
Reconnect Held Call .....................34
End Held Call................................34
End Current and Held Call ............35
Conference Calls...........................35
ransfer Calls................................36
Split Call........................................36
Reject Waiting Call........................37
Voice Notes.....................................37
Recording a Voice Note ................37
Voice Activation .............................38
Adding Voice ags for Phone
Book Entries...............................39
Using Voice Activation with Phone
Book Entries...............................40
Access Internet...............................41
Mobile Internet Home Menu..........41
Internet Browser Menu..................42
Using the Soft Keys......................42
Mobile Internet Messages.............43
Entering or Editing ext Within a
Mobile Internet Session..............43
Setting Up for Mobile Internet
Access........................................44
Setting a Bookmark ......................45
Internet Service Alerts ..................45
Making and Receiving Calls During
a Mobile Internet Session...........46
Ending a Mobile Internet
Session......................................46
Phone Book....................................46
Inserting Pauses into Phone
Numbers.....................................47
Voice Dialling................................48
Personal Numbers........................48
Last en Calls...............................50
My Phone Numbers......................51
Fixed Dialling................................51
Setup One- ouch Dialling.............52

Alarm Clock....................................53
Set Alarm ......................................53
Show Alarm Status........................54
Call Related Features.....................54
Show Battery Meter.......................54
Restrict My Phone Number...........54
Call Forwarding.............................55
Call Waiting...................................56
Call Barring ...................................57
Messages Menu..............................58
Call Voice Mail ..............................58
Received Messages......................58
Outgoing Messages ......................60
Message Editor.............................62
Voice Notes...................................62
Cell Broadcast...............................63
Message Settings..........................65
Phone Setup ...................................66
Select Phone Line.........................66
Adjust Ring Volume.......................66
Ring or Vibrate ..............................67
Set Ringer one ...........................67
Set Ringer one 2 ........................67
Set Alarm Ringer one.................67
Set Message Alert one............... 67
Edit Music one............................68
Quick Access Setup .....................69
Phone Lock................................... 69
Adjust Contrast.............................70
Require SIM Card PIN.................. 70
Change SIM PIN2 Code...............70
Unblocking Your V100 Personal
Communicator............................71
New Security Code.......................71
Extended Menus...........................72
Show ime and Date....................72
Set ime and Date........................72
Set ime Format...........................72
Language Selection......................72
Battery Saving Mode.................... 72
Select Keypad ones ...................72
Phone Status................................73
Net ork Selection..........................75
Available Networks........................75
Network Search.............................76
Preferred Networks .......................77
Find New Network.........................77
Call Meters Menu............................78
Show Call Charges .......................78
Show Call imers..........................79
Set Audible Call imers.................79
Set In-Call Display.........................79
Call Charge Settings .....................80
Lifetime imer ...............................81
Games .............................................81
Closing and Saving a Game .........81
owers of Hanoi............................82
Baccarat........................................83
Bricks ............................................84
Quick Access Menu ......................85
Adding Location Numbers to Features
in Your Quick Access Menu.......86
Adding/Editing Voice ags to Features
in Your Quick Access Menu.......86
Delete Voice ag..........................87
Special Characters ........................88
Accessories....................................90
Headset ........................................90
Power Adapter..............................90
Holster ..........................................90
Troubleshooting ............................91
Use and Care .................................95
Motorola Limited Warranty ..........96
Patents..........................................104
Index ............................................. 105
7
Safety Information
7
Safety Information
IMPOR AN INFORMA ION ON SAFE AND EFFICIEN OPERA ION
READ HIS INFORMA ION BEFORE USING YOUR PERSONAL
COMMUNICA OR
he information provided in this document supercedes the general safety
information contained in user guides published prior to July 2000. For information
regarding radio use in a hazardous atmosphere please refer to the Factory Mutual
(FM) Approval Manual Supplement or Instruction Card, which is included with radio
models that offer this capability.
RF Operational Characteristics
Your Personal Communicator contains a transmitter and a receiver. When it is ON, it
receives and transmits radio frequency (RF) energy. he Personal Communicator
operates in the frequency range of 900 MHz to 1990 MHz and employs digital
modulation techniques.
When you communicate with your Personal Communicator, the system handling
your call controls the power level at which your Personal Communicator transmits.
he output power level typically may vary over a range from 0.063 watts to 1.58
watts.
8
Safety Information
Exposure To Radio Frequency Energy
Your Motorola V100 Personal Communicator is designed to comply with the
following national and international standards and guidelines regarding exposure of
human beings to radio frequency electromagnetic energy:
• United States Federal Communications Commission, Code of Federal
Regulations; 47 CFR part 2 sub-part J
• American National Standards Institute (ANSI) / Institute of Electrical and
Electronic Engineers (IEEE) C95. 1-1992
• Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition
• National Council on Radiation Protection and Measurements (NCRP) of the
United States, Report 86, 1986
• International Commission on Non-Ionizing Radiation Protection (ICNIRP)
1998
• National Radiological Protection Board of the United Kingdom 1995
• Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to
Radiofrequency Electromagnetic Fields in the Frequency Range from 3 kHz
to 300 GHz, 1999
• Australian Communications Authority Radiocommunications
(Electromagnetic Radiation - Human Exposure) Standard 1999 (applicable
to wireless phones only)

9
Safety Information
9
o assure optimal Personal Communicator performance and make sure human
exposure to radio frequency electromagnetic energy is within the guidelines set forth
in the above standards, always adhere to the following procedures:
PORTABLE PERSONAL COMMUNICATOR OPERATION AND EME
EXPOSURE
Antenna Care
Use only the supplied or an approved replacement antenna. Unauthorized
antennas, modifications, or attachments could damage the phone and may violate
FCC regulations.
DO NOT hold the antenna hen the Personal Communicator is “IN USE.”
Holding the antenna affects call quality and may cause the Personal Communicator
to operate at a higher power level than needed.
Phone Operation
he communicator is designed to be used with a headset for talking and listening.
When placing or receiving a phone call, you must use the headset and speak
directly into the microphone.
Body- orn Operation
o maintain compliance with FCC RF exposure guidelines, if you wear a Personal
Communicator on your body when transmitting, always place the Personal
Communicator in a Motorola supplied or approved clip, holder, holster, case, or 10
Safety Information
body harness. Use of non-Motorola-approved accessories may exceed FCC RF
exposure guidelines. If you do not use a body- orn accessory, ensure the
antenna is at least one inch (2.5 cm) from your body hen transmitting.
Data Operation
When using any data feature of the Personal Communicator, with or without an
accessory cable, position the antenna of the Personal Communicator at least
one inch (2.5 cm) from the body.
Approved Accessories
For a list of approved Motorola accessories look in the accessory section of this
manual.
ELECTROMAGNETIC INTERFERENCE/COMPATIBILITY
Note: Nearly every electronic device is susceptible to electromagnetic interference
(EMI) if inadequately shielded, designed or otherwise configured for
electromagnetic compatibility.
• FACILITIES
o avoid electromagnetic interference and/or compatibility conflicts, turn off your
Personal Communicator in any facility where posted notices instruct you to do
so. Hospitals or health care facilities may be using equipment that is sensitive to
external RF energy.
11
Safety Information
11
• AIRCRAFT
When instructed to do so, turn off your Personal Communicator when on board
an aircraft. Any use of a Personal Communicator must be in accordance with
applicable regulations per airline crew instructions.
• MEDICAL DEVICES
Pacemakers
he Health Industry Manufacturers Association recommends that a minimum
separation of 6 inches (15 centimeters) be maintained between a handheld
wireless phone and a pacemaker. hese recommendations are consistent with
the independent research by, and recommendations of, Wireless echnology
Research.
Persons with pacemakers should:
• ALWAYS keep the Personal Communicator more than six inches (15
centimeters) from their pacemaker when the Personal Communicator is
turned ON.
• Not carry the Personal Communicator in the breast pocket.
• Use the ear opposite the pacemaker to minimize the potential for
interference.
• urn the Personal Communicator OFF immediately if you have any reason
to suspect that interference is taking place.
12
Safety Information
Hearing Aids
Some digital wireless Personal Communicators may interfere with some hearing
aids. In the event of such interference, you may want to consult your hearing aid
manufacturer to discuss alternatives.
Other Medical Devices
If you use any other personal medical device, consult the manufacturer of your
device to determine if it is adequately shielded from RF energy. Your physician
may be able to assist you in obtaining this information.
SAFETY AND GENERAL
• USE WHILE DRIVING
Check the laws and regulations on the use of Personal Communicators in the area
where you drive. Always obey them
When using your Personal Communicator while driving, please:
• Give full attention to driving and to the road.
• Use hands-free operation, if available.
• Pull off the road and park before making or answering a call if driving
conditions so require.

13
Safety Information
13
OPERATIONAL WARNINGS
• FOR VEHICLES WITH AN AIR BAG
Do not place a portable Personal Communicator in the area over an air bag or in
the air bag deployment area. Air bags inflate with great force. If the Personal
Communicator is placed in the air bag deployment area and the air bag inflates,
the Personal Communicator may be propelled with great force and cause seri-
ous injury to occupants of the vehicle.
• POTENTIALLY EXPLOSIVE ATMOSPHERES
urn off your Personal Communicator prior to entering any area with a poten-
tially explosive atmosphere, unless it is a Personal Communicator type espe-
cially qualified for use in such areas as “Intrinsically Safe” (for example, Factory
Mutual, CSA, or UL Approved). Do not remove, install, or charge batteries in
such areas. Sparks in a potentially explosive atmosphere can cause an explo-
sion or fire resulting in bodily injury or even death.
Important: he areas with potentially explosive atmospheres referred to above
include fueling areas such as below decks on boats, fuel or chemical transfer or
storage facilities, areas where the air contains chemicals or particles, such as grain,
dust or metal powders, and any other area where you would normally be advised to
turn off your vehicle engine. Areas with potentially explosive atmospheres are often
but not always posted.
14
Safety Information
• BLASTING CAPS AND AREAS
o avoid possible interference with blasting operations, turn off your Personal
Communicator when you are near electrical blasting caps, in a blasting area, or
in areas posted: “ urn off two-way radio.” Obey all signs and instructions.
OPERATIONAL CAUTIONS
• ANTENNAS
Do not use any portable Personal Communicator that has a damaged
antenna. If a damaged antenna comes into contact with your skin, a minor burn
can result.
•BATTERIES
All batteries can cause property damage and/or bodily injury such as burns if a
conductive material such as jewelry, keys, or beaded chains touch exposed ter-
minals. he conductive material may complete an electrical circuit (short circuit)
and become quite hot. Exercise care in handling any charged battery, particu-
larly when placing it inside a pocket, purse, or other container with metal
objects.
15
Safety Information
15
European Union Directives Conformance Statement
his product is in conformance with the requirements of the applicable
EU Council Directives. Declarations of Conformance with the
requirements are located at:
Motorola Ltd.
Personal Communications Sector -
Europe, Middle East and Africa
Midpoint, Alençon Link
Basingstoke, Hampshire RG21 7PL
United Kingdom
APPROVED for connection to
telecommunicationssystemsspecified
in the instructions for use subject to
the conditions set out in them.
S/1357/4/V/503894
16
Getting Started
Getting Started
Installing the SIM Card and Battery
Before you can send or receive messages or calls, you need to install your SIM
(Subscriber Identity Module) card and the battery. he SIM card that was supplied
by your service provider contains your Personal Communicator’s number, service
details, and memory for storing numbers and messages.
Note: Some networks let you make emergency calls without a SIM card.
Note: Your SIM card can be used in someone else’s personal Personal
Communicator and you will be charged for the call, so keep it in a safe place. Do not
bend or scratch it and do not expose it to static electricity or water.

17
Getting Started
17
SIM Card and Battery Installation
1. Remove the battery cover.
2. Slide the SIM card into the
recess so that the notch in the
card lines up with the notch in the
recess.
3. Align the contacts on the battery
with the contacts in the battery
compartment and press
downwards toward the contacts
until the battery clicks into place.
4. Replace the battery cover.
Note: If the SIM card is inserted
incorrectly, “Check Card” is displayed. Remove the SIM card and re-insert it. If the
card does not work, contact your service provider.
Charging Your Battery:
• Charge the battery by inserting the adapter plug into the port on your Personal
Communicator and plugging the adapter into a wall outlet.
• Charge your battery at room temperature and never leave it in really hot, cold, or
wet places.
• Charge only Motorola batteries in your Personal Communicator.
SIM Card
Recess
Battery
Charger
Port
Slide Battery
Door Lock
to Open
Slide to Remove
Battery Door
Battery
Compartment
18
Getting Started
Control Buttons
}
]
19
Getting Started
19
, Press and hold to turn on or off.
( Press to accept and end a call, setting, or option.
) Used to reject or cancel a call, setting, option, and to return to the
previous screen. When in text mode, press to delete the previous
character.
$ Press to enter the Quick Access menu.
% Press to access the Main Menu.
!Use to scroll through menus and text, and increase and decrease
volume.
#Press to read a message.
.Press to write a message.
M (0 - 9) Press for AL and 0 - 9 numbers.
M * Press for symbols and additional characters.
]Smart Button. Use to access your Phone Book and make calls
using Voice ags.
+ Press once to capitalise a letter. Press twice for continuous
capitalisation, press twice to stop capitalisation. 20
Getting Started
The Display
} When the communicator is closed, or in the holster, press to answer
and end a call.
&Press to start and stop recording voice notes.
Note: use of this feature is subject to varying state, federal, and
country laws regarding privacy of phone conversations.
ABC123 Displays text and numbers.
/ Signal Strength. he more segments, the stronger the signal strength.
kA call is in progress or hanging up.
lDisplayed when on a system other than your home system.
:Home Zone. Availability depends on your service provider.
IDisplayed when a Short Message Service (SMS) message is received.
Flashes when you have an unread SMS message, or your message
storage area is full. (Note: SMS Messaging is a network and
subscription dependent feature and may not be available in all areas.)
JDisplayed when you have voice mail. Availability depends on your
service provider.

21
Getting Started
21
Backlight
Your Personal Communicator’s backlight turns on any time a button is pressed, and
remains on during keyboard activity.
Note: Prolonged use of the backlight may shorten battery life.
Turning On Your V100 Personal Communicator
Press and hold , until your Personal Communicator vibrates or makes a sound.
Note: If the SIM card is not installed, your Personal Communicator displays a
message to install one.
Entering Your SIM Card Personal Identification Number (PIN)
When prompted, enter your PIN and press (.
• If you make a mistake, press and release ) to remove the last character, or
hold down ) to remove multiple characters.
\Call Ringer is On.
>Battery Charge Indicator. he more segments, the stronger the charge.
B...KDisplayed when the Quick Access menu is open.
zMenu item is currently selected.
12:00 Real ime Clock. Displays the time in either AM/PM or 24 hours.
22
Getting Started
• If you enter the wrong PIN, your Personal Communicator lets you know with a
displayed message.
Note: If the correct PIN is not entered within three attempts, your Personal
Communicator locks up. See “Change Unlock Code” on page 70.
Entering Your Unlock Code
When prompted, enter your unlock code, then (.
Note: If you forget your unlock code, press %(, enter your security
code, enter a new unlock code, then press (.
When a network name is displayed, it means your Personal
Communicator is ready for use.
Turning Off Your Personal Communicator
Press and hold ,.
23
Tips on Using this Guide
23
Tips on Using this Guide
The Main Menu
Your Personal Communicator’s features are
accessible through the Main Menu. Press % to
display the Main Menu. o scroll through the Main
Menu, use !. Press ( to enter a submenu.
Menu Navigation
Many of your Personal Communicator’s features are accessed by using menus and
submenus for selection, change, or cancellation. Please read this section carefully.
When you understand the menu navigation, you will be able to access and change
settings with ease.
Entering the Menus
•% - press to enter the Main Menu when your Personal Communicator is in
the Standby mode.
•$ - press to enter the Quick Access menu.
Main
Access Internet
Phone Book
Alarm Clock
Select?
Main Menu Example
24
Tips on Using this Guide
Getting Around in the Menus
• ! - to scroll through menu selections.
• ( - to enter the selected menu and to accept and
confirm settings.
• ) - to go to the previous screen without making
changes. (When in text mode, use to backspace and delete
characters.)
• z - indicates the current setting of a feature (usually on or off).
Note: When “View Options?” is displayed, a submenu exists for that menu
selection. Press ( to enter the submenu and to accept and confirm settings.
Exiting the Menus
•) - press and hold for 2 seconds to exit any menu or screen and return to the
Standby screen.
Short and Extended Menus
As you become accustomed to the menus and features you use the
most, you can select which menus you want readily accessible, and
which ones to store out of view.

25
Tips on Using this Guide
25
With extended menu, all features are always displayed. When you remove a feature
from the short menu, it is not displayed until you choose to display it.
1. o move a feature from the short menu to the extended menu, highlight the
feature then press and hold ( until a menu prompting a decision is displayed.
2. Select either to remove or keep it on the short menu, or to add it to the short
menu or keep it in the extended menu.
Note: If a feature cannot be moved to the short menu, your Personal
Communicator will let you know with a message.
Note: o turn extended menus on or off, refer to “Extended Menus” on page 72.
Ho to Use the Control Buttons
he control buttons are represented as graphics which look like the buttons on your
Personal Communicator. A sequence of button presses might be shown
as:%().
his means that you would press %, then ( and then ) in sequence, not at
the same time.
Prompts and Messages
Your Personal Communicator responds to button presses by
displaying easy to understand prompts to guide you to the next
action, or simple messages confirming that your action is
complete. 26
Tips on Using this Guide
Testing Your V100 Personal Communicator
It's a good idea to test your service by sending a Short Message Services
(SMS) message or by calling a friend or family member, from your Personal
Communicator. Start by using the phone number, web site, or email address (and a
PIN, if required) your service provider gave you, then try making a call. When you
reach a friend or family member, ask them to send a message to you or call you
back.
Refer to the following sections for information about SMS messages and making
and receiving calls. If your Personal Communicator does not send or receive
messages or calls, contact your service provider. After you've tested your Personal
Communicator, read the rest of this guide to learn about the many useful features of
your new Personal Communicator.
Note: SMS messaging is a network and subscription dependent feature and may
not be available in all areas.
27
SMS Messaging
27
SMS Messaging
Your Personal Communicator can send and receive Short
Message Services (SMS) messages of up to 160 characters
that are sent by your service provider. hese messages are
transmitted for a limited amount of time. If a memory location
is not available before the message is removed from the
network, it is not stored.
Note: SMS messaging is a network and subscription feature and may not be
available in all areas.
Sending an SMS Message
1. Press ..
2. ype your message.
3. When your message is complete, press (.
4. From the message editor, select to send the message, then press (.
5. Choose from the menu selections to enter the phone number, then follow the
prompts given by your Personal Communicator.
6. When the phone number you want to send your message to is displayed,
press (.
28
SMS Messaging
Entering Text
• o type a capital letter, press and release +, then type the letter.
• o type multiple capital letters, press ++. o switch back to lowercase
letters, press ++ again.
• If you make a mistake while typing, press ) to erase the previous character. o
erase multiple characters, press and hold ). You can use ! to move to a
character or line to make a correction.
• o enter special characters, refer to “Special Characters” on page 88.
Entering Numbers in Text Mode
• o type a single number, press M then type the number.
• o type a series of numbers, press M M. o stop entering numbers, press
M M again.
Storing an SMS Message
1. Press . and type your message.
2. Press (.
3. Select the store option, then press (. Your message is automatically stored in
the Outgoing Message folder.

29
SMS Messaging
29
Receiving and Reading an SMS Message
Cool...I got a message! Before long you’ll be getting a lot of
messages.
When a SMS message is received, your Personal Communicator
alerts, displays I and stores the message. he I flashes until
the message is read. If there is not enough memory to store the
message the I flashes after you read the message. One or more
messages must be deleted before the message can be stored.
1. Press # to read the message.
2. Select your view options for the message and press (.
3. You can reply to the message, store it, or delete it.
Note: If you send and receive a lot of SMS messages, battery life could be
shortened.
30
SMS Messaging
Sending Email Messages
Contact your service provider to find out if this option is supported and to get the
email server number.
1. ype the email address followed by either a space or a number sign (#), then
type the message text. For example, to send a “Hello” message to email
address “[e-mail]” type abc1 3:isp.com#Hello.
Note: Depending on your service provider, you may need to use a space in
place of the number sign (#) between the address and the email text.
2. When your message is complete, press (.
3. From the Message Editor, select to send the message, then press (.
4. Choose Phone Number Entry, then enter the email server number.
5. When the email server number is displayed, press (. Observe that “Sending”
is displayed.
Note: If you get the “Unable to deliver message” error, return to the email
address and try replacing the number sign (#) with a space, or vice versa.
31
Making a Call
31
Making a Call
Note: Don’t forget to use your headset so you can hear your call.
Use ! to decrease or increase the volume level.
Note: You can press ] to quickly go to your Phone Book, select the
number you want to call, then press (.
Enter the phone number, then press (.
Note: If you make a mistake, press and release ) to remove the last character, or
hold down ) to remove multiple characters.
International Phone Calls
1. Press and hold 0 (zero) until + is displayed.
2. Enter the country code, then the phone number. he country code follows the
conventional format, 44 for the UK, 46 for Sweden, etc.
As for a conventional international call, remove the first “0” of the area code you dial.
GSM Emergency Calls
he world-wide GSM standard provides a single number, 112, to dial in cases of
emergency. he emergency call is directed to a central operator. he call can be
made without any security codes and, depending on the network, without a SIM
card inserted.
o dial the GSM emergency number, press 11 (.32
Receiving a Call
Ending a Call
Press ( or ).
Redialling the Last Number Called from Standby Mode
Press (((.
Receiving a Call
Note: Don’t forget to use your headset so you can hear your call. Use !
to decrease or increase the volume level.
Press ( to answer the call.
Note: When your Personal Communicator is closed or in the holster, you can press
}, located on the outside of your Personal Communicator, to answer a call right
away.
In-Call Menu
here are lots of things you can do during a call. o access the in-call menu, press
% during a call, to exit the menu, press ).
Note: Menu selections depend on the state of the call, the type and setting of your
SIM card, and your subscription to these services. he following paragraphs explain
all possible options.

33
In-Call Menu
33
Hold Call
You can place a current call on hold and accept an incoming call, or start a
second call.
To Put an Active Call on Hold:
1. Press % (.
2. o reconnect, press (.
Make a Ne Call
Select this option to put an active call on hold and make a call to
someone else.
1. Press %.
2. Select the make a new call option, enter the number, then press (.
3. o end the new call and go back to your first call, press %(.
Turn Mute On or Off
urns the microphone off during a call. Select again to turn the microphone back on.
Restrict My Number
You can keep your Personal Communicator’s number a secret while you make a call.
34
In-Call Menu
End Active Call
When a call comes in while you are already on a call, you can end the active
call.
1. Press ( to put the active call on hold.
2. Press %, select the end active call option, then press (.
Note: If you have a call on hold, it becomes your active call.
Reconnect
Use to go back to a call that’s on hold.
Reconnect Held Call
his is similar to Reconnect. If you have a call on hold, and a call waiting, select this
option to connect with your held call.
End Held Call
ime to say bye to the person you put on hold.
1. Press %.
2. Select End Held Call, then press (.
35
In-Call Menu
35
End Current and Held Call
Select this to say bye to everyone.
Conference Calls
Let’s have a phone party! If you have both Conference Call and Call
Waiting, you can talk to up to 5 people at the same time.
Starting a Conference Call:
1. Call one of the people you want to conference with.
2. Place the active call on hold, dial another phone number, then press
(.
3. Press % then select Conference Call.
Note: here may be times when your request is not successfully completed.
Wait a little while, then try your call again.
To Add a Person to Your Conference Call:
1. Place the Conference Call on hold.
2. Add a new call by:
• Entering the phone number.
• Making a new call.
• Recalling a Phone Book Entry.
• Answering a Call Waiting.
3. Select In-Call then Conference Call to bring in the new call. 36
In-Call Menu
Transfer Calls
If you have both Conference Call and Call Waiting, you can
transfer a call to another phone.
Initiating Transfer Call Before Third Party is Connected:
1. Press % and select the transfer call option.
2. Enter the number to where you want the call transferred, then press (. When
the call is transferred, you are disconnected automatically.
Note: here may be times when a call transfer is not completed successfully.
Please try again.
Initiating Transfer Call After the Third Party is Connected
Press % and select the transfer call option. After the call is transferred, you are
disconnected automatically.
Split Call
Want to share a secret or a private joke with someone? Split call allows you to
separate a conference call member and have a private conversation with them.
Note: You cannot have any calls on hold to have a split call.
1. Press % then select Split Call.
2. Press ! until the phone number of the person you want to separate from the
conference call is displayed, press (. You can now talk privately to the person.

37
oice Notes
37
3. o re-join both of you to the Conference Call, re-select Conference Call from
the In-Call menu.
Reject Waiting Call
When you’re too busy to talk, you can reject an incoming call by pressing and
holding ).
Voice Notes
With voice notes, you can record up to three minutes of voice messages for yourself
or record part of a call. You can record when your Personal Communicator is idle,
when you are on a single call, or when you are on an active call with a waiting call.
Note: Use of this feature is subject to varying state, federal, and county laws
regarding privacy of phone conversations.
Recording a Voice Note
1. o start recording, press &.
2. o stop recording, press & again.
Notes:
• When recording a call, both parties are recorded and the other party hears a
tone every 10 seconds.
• Recording stops automatically if you accept or make a call. 38
oice Activation
• While recording, your Personal Communicator alerts you at ten seconds,
and again at one second before recording capacity is reached. If you do not
stop, recording automatically stops.
o listen to your voice note, select voice notes from the Messages menu.
Voice Activation
With Voice Activation you can dial a phone number or access a feature with a single
spoken command called a Voice ag.
You can assign up to 25 Voice ags to Phone Book numbers and up to 9 Quick
Access features. Notes:
• You cannot assign Voice ags to numbers in your SIM card
memory.
• For best results, make sure there is no background noise and
speak in a clear, natural voice when recording.
• Your Personal Communicator can record two seconds for each
Voice ag.
• You cannot record Voice ags if you have selected to prevent access to phone
memory, see “Prevent Access” on page 50.
39
oice Activation
39
Adding Voice Tags for Phone Book Entries
You can have up to 25 Phone Book Voice ags, and add a new Voice ag when
you set up a Phone Book entry.
Add Voice Tag
When you add an entry to your Personal Numbers list, your Personal Communicator
asks you if you want to add a Voice ag. If you don’t want to add a Voice ag,
press ).
To Add a Voice Tag:
1. Press (.
Note: If there are already 25 Phone Book Voice ags in your Personal
Communicator, you need to delete one before you can add another.
2. When prompted by the Personal Communicator, press ( and record after the
tone.
3. When recording is successful, your Personal Communicator returns to the Add
o Phone Memory menu.
Note: If the recording is not successful, the Personal Communicator prompts
you to record again.
Add or Edit Voice Tag:
If an entry has a Voice ag, )) is shown before the location number.
1. Find the entry either by name or location. 40
oice Activation
2. Press (, then select to add or edit the Voice ag.
3. o add the Voice ag, follow the steps in “Add Voice ag” above.
Delete Voice Tag:
1. Find the entry either by name or location, see “Personal Numbers” on page 48.
2. Press (, select the delete option, then press ( again.
Using Voice Activation ith Phone Book Entries
You can easily access phone book entries that have Voice ags assigned
to them.
Voice Activation from the Standby Mode:
1. Press ]. When prompted, say the Voice ag name. he Personal
Communicator highlights the matching entry in your phone book list. If there is
no matching entry, the Personal Communicator highlights an alternate entry in
the list.
2. Press ( to make the call, ! to select a different entry, or ) to cancel.
Voice Activation from the Phone Book Menu:
1. Select Voice dialling from the Phone Book menu.
2. When prompted, press ].
3. When prompted, say the Voice ag name. If a matching entry is found, the
Personal Communicator highlights it or highlights an alternate entry in the list.
4. Press ( to make the call, ! to select a different entry, or ) to cancel.

41
Access Internet
41
Access Internet
When you’re on the go, you can still keep up with the latest
news, sports scores, entertainment stories, check flight status,
and much more. Access Internet is a network and subscription-
dependent feature that offers mobile Internet access of
Information Services and certain web sites using the Wireless
Application Protocol (WAP). Contact your service provider for details about these
services.
Mobile Internet Home Menu
Note: Your service provider determines the layout and information shown on your
Personal Communicator.
After connection is made, your ISP’s Home menu is displayed. A typical Home menu
page might contain the name of your ISP and a list of options to select from.
1. Highlight the option menu you want, then press (.
2. o return to the previous screen, press ).
If the text in a menu is too wide for the screen, the Personal Communicator uses two
screens and repeats each half of the menu until you make a selection.
42
Access Internet
Internet Bro ser Menu
To display the browser menu:
1. Press and hold % for at least 2 seconds.
Note: If you release % too quickly, you might enter the menu for the
currently highlighted option.
2. Scroll to the menu selection you want, then press (.
A typical bro ser menu might include:
• Help - provides help for the previously highlighted option.
• Home - returns you to your ISP’s home page.
• Mark site - lets you add a site to your Bookmarks folder.
• Setup - contains the options to set up your ISP access.
Using the Soft Keys
During a mobile Internet session, the functions of the
% and ( buttons change to accommodate the
current display. In the example display, to go back to
the previous screen, you need to press (, to quit
and exit, you need to press %.
When you want to go to a previous screen, press ).
Menu
1>O tion 1
2>O tion 2
u Exit Back
Soft Ke
y
s Example
43
Access Internet
43
Mobile Internet Messages
Messages displayed in the bottom left portion of the screen indicate when
activities such as receiving or sending data, connecting to the Internet, and
Internet activities are being performed. A u indicates you are in a non-secure
Internet location.
Note: Your ISP determines the icons and messages displayed on your Personal
Communicator.
Entering or Editing Text Within a Mobile Internet Session
You can enter or edit text the same way you do for all other text
functions. However, you can’t access the non-Roman characters.
• For a single capital letter, press and release +.
• For multiple capital letters, press ++. o switch back, press
++ again.
• Press ) to erase the previous character, press and hold for
multiple characters.
• For a single number, press M then type the number.
• For a series of numbers, press M M. o stop entering numbers, press M
M again.
44
Access Internet
Setting Up for Mobile Internet Access
Your service provider may set up your mobile Internet access for you.
If not, you will need the following user information to set it up:
•Primary Data Gate ay: the IP address to access the mobile
Internet.
•Phone Number: the number your Personal Communicator calls to access the
Internet. his is provided by your ISP.
•User Name: provided by your ISP.
•User Pass ord: provided by your ISP.
•Baud Rate: this is likely to be 9600, the standard data rate for GSM phones.
•Idle Time Out: the amount of time the Personal Communicator waits before
hanging up if it detects no Internet activity.
•Line Type or Port: modem or ISDN.
•Connection Type: non-transparent or transparent.
For Internet Access
ext Character ~€^[{]}|\
Press M * then
press... YDFFFGGGM?

45
Access Internet
45
To set up your mobile Internet access:
1. From the browser menu, select Setup, then press (.
2. Enter your user information by first selecting an item and choosing the
softkey to edit it as necessary.
3. When you have entered all information, exit to the Standby Screen, turn your
Personal Communicator off and then on again to register all information or
changes.
Setting a Bookmark
You can set up bookmarks so you can quickly access your favourite Internet sites.
1. From your browser menu, select Mark Site.
2. Press any key from 1 to 9 when prompted. he Personal Communicator
provides a confirmation message that the bookmark has been stored.
3. o go back to the bookmark, press and hold the appropriate location number
key (1 to 9).
Internet Service Alerts
You do not need to be using the mobile Internet to receive an Internet service alert.
When you receive an alert, the Personal Communicator displays a screen with the
details. Press ( to view the contents or ) to reject it.
46
Phone Book
Making and Receiving Calls During a Mobile Internet Session
You must first end the mobile Internet session, then make your call
in the normal way. If you receive a call, press ( to accept it ) to
reject it.
If you answer a call, press ( to resume your mobile Internet
session or ) to return to the Standby mode.
Ending a Mobile Internet Session
Press and hold ) until your ISP’s Home page is displayed, then press ) again.
Note: o quickly exit a mobile Internet session, press ].
Phone Book
You can store important numbers in your Phone Book so you can
retrieve them quickly and easily.
Your Personal Communicator can store up to 100 entries and the SIM
card can store up to 155 entries in your Personal Numbers list. he
number of SIM card entries varies depending on the type of SIM card
issued by your service provider.
You can store up to 40 entries in a fixed dialling list, if you have this feature. Fixed
dialling allows limited use of your Personal Communicator to particular numbers, or,
if you wish, to country codes, area codes, or other prefixes of your choosing.
47
Phone Book
47
Each Phone Book entry contains:
• A telephone number. Up to 32 digits can be stored, but this is reduced to 20
digits for SIM card locations.
• A name. Up to 16 characters for phone locations. Up to 50 characters for SIM
card locations.
• A location label. From 1 to 255 in your Personal Numbers list. From 1 to 40 in
your Fixed Dial list.
Inserting Pauses into Phone Numbers
Pauses can be inserted into a string of numbers to allow the called number time to
react to certain activities such as going into voice mail or entering a password.
o insert a three-second pause in a phone number, press and hold (*) until Ü is
displayed.
For example, you have voice mail on 555-6911, with mailbox number 1066 and
password 2001. hen you can dial: 5556911Ü1066Ü2001 then press (.
he first part of the number calls the voice mail system. When the call is answered,
there is a pause before the tones for 1066 are sent. hen there is a second pause
before the tones for your password of 2001 are sent.
48
Phone Book
Voice Dialling
You can quickly access a phone number that has a Voice ag
assigned to it.
1. When selected, your Personal Communicator prompts you to press the Smart
button ].
2. Next, you are prompted to say the name (Voice ag) after the tone.
3. Press ( to make the call, or highlight a different selection then press (.
Personal Numbers
Use to create and manage your list of personal numbers.
Find Entry By Name
Use to find a number from your list of Phone Book names by typing
up to three of the first characters of the name, then press (.
Find Entry By Location
Use to select a number from your list of Phone Book locations.
1. At the prompt, enter a location number, then press (. If the number is not
valid, the Phone Book list is displayed and the number closest to your entry is
highlighted.
2. Use ! to navigate through the entries.

49
Phone Book
49
3. Press ( to make your selection. From the submenu select:
• Switch View - to display the information for the selected entry.
• Call Number - to call the selected number.
• Modify Name or Details - to modify the information for the selected entry.
• Erase Name and Number - to delete the phone book entry.
• Add or Edit Voice ag - to add or edit a Voice ag.
Add Entry
Allows you to add a phone number and name to the Personal Communicator’s
(phone) memory or to SIM card memory.
1. When prompted, enter the phone number, name and a location number. If you
do not specify a location number, the entry is stored in the next available
location.
2. he Personal Communicator then asks if you want to enter a Voice ag. For
Voice ags information, see “Add Voice ag” on page 39.
3. If you don’t want to add a Voice ag, press ).
Check Capacity
Use to check the number of free Phone Book or SIM card memory areas. From the
submenu you can:
• Check Phone Capacity and Check SIM Capacity - displays the phone and SIM
capacity. 50
Phone Book
Prevent Access
Select to prevent access to your Personal Numbers list.
Note: You will not be able to record Voice ags if you choose to prevent access
to phone memory.
• o SIM Card Memory, o Phone Memory, o Phone & SIM Memory, No Memory
Restrictions - You can prevent access to your SIM card memory, the Personal
Communicator’s memory, both, or cancel all access restrictions. o change
restrictions, follow the instructions given by the Personal Communicator.
Last Ten Calls
When selected, allows you to review time and date information of your
last 10 missed or answered calls, or to calls you made. Depending on
your selection, you can redial a phone number, store a phone number,
or erase all of the phone numbers.
Note: his list is erased when a new SIM is inserted in the Personal
Communicator.
51
Phone Book
51
My Phone Numbers
When selected, displays your list of phone numbers. From the submenu, you
can:
• Modify Name or Details - to make changes to the selection.
• Switch View - to display information for the selected entry.
Note: he list is stored on your SIM card. Depending on your service provider, one
or more of these entries is already defined and you may not be able to change them.
Fixed Dialling
Limits the use (typically third-party) of your Personal Communicator to a list of
predefined telephone numbers, country codes, area codes, or other prefixes. When
set, the Personal Communicator does not allow dialling of any number other than an
emergency number. his option may be affected by the call barring setting.
Note: Fixed dialling is a network and subscription dependent feature and may not
be available in all areas.
View Fixed Dial List
Use ! to scroll through the list of numbers. Press ( to make a call.
52
Phone Book
Setup Fixed Dialling
Use to turn fixed dialling on or off, and to enter or change entries in the list. After
you enter your PIN2 code, you can:
• On - turn fixed dialling on.
• Off - turn fixed dialling off.
• Edit Entry - scroll to the entry you want to change, press ( to edit the entry or
) to erase it.
• Add Entry - to add a phone number and name, and a location number. If you do
not specify a location number, the entry is stored in the next available location.
• Erase Entry - scroll to the entry you want to delete then press (.
Setup One-Touch Dialling
You can specify which phone book list is one-touch dialled. he
selections are:
• o Phone Memory - changes One- ouch Dialling to your Personal Numbers list
(locations 1 to 9).
• o SIM Card Memory - changes One- ouch Dialling to your Personal Numbers
list stored on your SIM card (locations 101 to 109).
• o Fixed Dial list - changes One- ouch Dialling to your Fixed Dial list (locations 1
to 9).

53
Alarm Clock
53
One-Touch Dialling from Phone Book Numbers
o quickly retrieve and dial a number stored in one of the first nine
locations of your Phone Book, press and hold the appropriate
number key. For example, press and hold to call the phone number
stored in location 2 of your phone book.
Dialling Phone Book Numbers with Smart Button
• Press ] and say the Voice ag name after the tone.
• Press ] then scroll to the number, or press the appropriate number to skip to
a particular letter.
Alarm Clock
You can set up to 5 alarms on your Personal Communicator, and attach a
40-character memo to each alarm.
Set Alarm
Each alarm can be set to alert on a specific day and time, daily, weekly, every
Monday to Friday, or every Monday to Saturday.
1. o set an alarm, select the day(s) for the alarm to occur.
2. When prompted, enter the alarm time using the keypad numbers and press (.
3. When prompted, enter your reminder memo then press (.
Note: Depending on your alarm selection, you may be required to enter a date. 54
Call Related Features
Sho Alarm Status
When selected, displays the alarms that are set. Use ! to select an alarm.
From the submenu, you can:
• Switch View - see the details for alarm. Select Switch View again to return to the
previous screen.
• Edit Alarm - change the time, date, and attached memo.
• Disable Alarm - suspends (but does not delete) the alarm.
Call Related Features
Sho Battery Meter
Displays the remaining battery charge. he more segments displayed, the more
battery charge is left.
Restrict My Phone Number
his is a network dependent feature. Please check with your service provider for
more information.
Show ID on Next Call
Sends your Personal Communicator’s number with the next call.
55
Call Related Features
55
Restrict ID on Next Call
Prevents your Personal Communicator’s number from being sent with the next
call. You need to reselect this option each time you want to restrict your ID.
Call For arding
You can have incoming calls sent to other phone numbers.
Note: You cannot set call forward when you are out of your network
coverage area.
Note: Call Forwarding is a network and subscription dependent
feature and may not be available in all areas.
Forward Voice Calls
You can have voice calls sent to other phone numbers. From the submenu you can:
• Forward When Unavailable - forwards all incoming voice calls to a single
number whenever your Personal Communicator is unavailable. o forward,
select On, then enter a forwarding phone number.
Note: When set to On, has the same effect as setting all “Detailed Forwarding”
options to On and takes priority over Detailed Forwarding settings.
56
Call Related Features
• Forward All Voice Calls - forward all incoming voice calls to a single number.
o forward, select On, then enter a forwarding phone number.
Note: When set to On, this option takes priority over all other voice call
forwarding settings.
• Detailed Forwarding - forwards voice calls to different numbers, depending on
the current status of your Personal Communicator.
he selections are:
† If Busy - forwards calls when your Personal Communicator is engaged.
† If Not Reachable - forwards incoming calls when your Personal
Communicator cannot be contacted by the network.
† If No Answer - forwards incoming calls when you do not answer.
• Cancel All Forwarding - cancels forwarding of incoming calls, resets all
forwarding settings to Off, and removes all forwarding numbers.
Call Waiting
When set to On, you are notified of a waiting call by an audible
alert and a call waiting message. Press ( to answer the call or
) to reject it.
If you have Caller Line Identification, the caller’s number or name
is displayed instead of the Call Waiting message. Availability of
this feature depends on your service provider.

57
Call Related Features
57
Note: Call Waiting is a network and subscription dependent feature and may not
be available in all areas.
Call Barring
Call barring is a network feature which can be used to bar outgoing and incoming
calls. If you change the setting, you may be asked to enter your barring password.
here is a short delay while the Personal Communicator notifies the network of the
new setting. When the change is made, the Personal Communicator displays a
confirmation message.
Note: he initial password is supplied to you by your service provider. his option
may be affected by the Fixed Dialling setting.
Bar Outgoing Calls
• Int’l Calls - bars all outgoing international calls.
• Int’l Calls Except Home - bars all outgoing international calls except those to
your home country.
• All Calls - bars all outgoing non-emergency calls.
• Off - removes call barring for all calls.
Bar Incoming Calls
• When Roaming - bars incoming calls when you are roaming.
• All Calls - bars all incoming calls.
• Off - removes call barring for all calls. 58
Messages Menu
Cancel All Barring
Cancels this option for all calls.
Change Bar Password
When prompted, enter the current password, then enter and confirm a new 4-digit
password.
Messages Menu
Call Voice Mail
Select to make a call to your voice mail number.
Note: Voice mail is a network and subscription dependent feature and may not be
available in all areas.
Received Messages
Note: For quick access, press #.
Displays the number of new and old SMS messages, then displays the
message list.
1. Use ! to scroll through your message list.
2. Most times, only a portion of your message is displayed. o view the entire
message, press (to see your options.
59
Messages Menu
59
Switch View
Displays the entire message. Press ( to return to the view options screen.
Delete Message
Deletes the message.
Note: Before you delete a message, make sure the message you want deleted was
selected in your received message screen.
Retrieve Numbers
You can retrieve all numbers embedded inside an SMS message. You can call the
number, store it into your Personal Communicator, or store it into SIM card memory.
Press ( while viewing the numbers.
Note: Only 20 characters (32 characters, if GSM1900) of a number can be
retrieved. If the number is longer than allowed, the remaining characters are not
retrieved. Space and - (dash) characters are not counted as part of the character
length.
Reply to Message
ype your message then press ( to send it.
Return Call
When there is a phone number attached to a message, you can call the person who
sent the message to you. 60
Messages Menu
Edit Message
You can use the message editor to edit the message. hen you can either send
the edited message or store it in your Outgoing Message list.
Go to Next Message
Displays the next message in the list.
Delete All Messages
Deletes all messages, read and unread.
Note: Once deleted, messages are not retrievable. It’s a good idea to
make sure you have read all your messages before deleting them.
Outgoing Messages
Note: You cannot send outgoing messages until the Message Service Centre
number has been set.
You can view and manage your outgoing messages that are stored on your SIM
card. When selected, the number of messages is displayed followed by the first
message in the list.

61
Messages Menu
61
To Send a Stored SMS Message
Select the message from your message list, press ( to view your
options, then send it.
Switch View
Displays the entire message. Press ( to return to the view options
screen.
Send Message
Add the destination phone number then send a message. From the submenu select
to either enter the number, find it by name, or find it by location.
When you have set up a destination phone number, select ( to send the message,
press ( again to confirm.
Edit Message
Use to edit a message, then send or store it in your Outgoing Messages list.
Delete Message
Use to delete the current message.
Note: Before you delete a message, make sure the message you want deleted was
selected in your received message screen.
Go to Next Message
Use to display the next outgoing message. 62
Messages Menu
Message Editor
Compose an SMS message and send it to a friend, or store it to
send it later.
• For a single capital letter, press and release +, then type the
letter.
• For multiple capital letters, press ++. o switch back to
lowercase letters, press ++ again.
• Press ) to erase the previous character, press and hold ) to erase multiple
characters.
• For special characters, see “Special Characters” on page 88.
• For a single number, press M then type the number.
• For a series of numbers, press M M. o stop entering numbers, press M
M again.
Note: You don’t always have to come to this menu to get to your
message editor, you can press . from any screen for immediate access.
Voice Notes
Play, erase, or show remaining time available for your recorded voice notes. See
“Voice Notes” on page 37 for more information.
63
Messages Menu
63
Play Voice Note
1. Scroll to the voice note you want to play, then press (.
2. Press ) to stop playback.
3. o erase, set an alarm for a voice note, or go to the next voice note, press ( to
display the options menu.
• Erase Voice Note - erases the selected voice note.
• Set Alarm (Alarmed voice notes) - You can set an alarm to up to 5 voice
notes. See “Set Alarm” on page 53.
• Go to Next Voice Note - selects and plays the next voice note in the list.
4. Press ) to return to the previous menu.
Show Time Available
Displays the remaining recordable time.
Erase All Voice Notes
Erases all recorded voice notes
Cell Broadcast
hese are general messages that your service provider
broadcasts in numbered channels to all Personal Communicators
in a geographic area. Please contact your service provider for a list
of available channels and the information they provide.
64
Messages Menu
Note: Your Personal Communicator can receive broadcast messages only
when it is in Standby mode.
While a broadcast message is scrolling across the screen, you can:
• Press ! to stop and start the message.
• Press ) to remove the message.
Note: he ! functions change while you are receiving a cell broadcast message.
You need to remove the message before ! functions return to normal.
When the message is complete, the beginning of the message remains displayed
until you remove it, a new message arrives, or you leave the geographic area.
From the Cell Broadcast submenu, you can select On to receive these messages, or
Off to stop receiving them.
Note: Selecting Off causes deletion of all stored cell broadcast messages.
Channel List
• Channel Index - displays a list of available channels that you can edit. When you
edit a channel, you also remove any message associated with it. Select the
channel index you want to modify then press (. ype in the channel number
and press (. he channel details are stored and your Personal Communicator
returns to the channel index list.
• Delete All Channels - to delete all channels.

65
Messages Menu
65
Language List
Use to select a different language for Cell Broadcast messages. Availability
depends on the type and settings of the SIM card, and/or your subscription to
this feature.
Message Settings
Voice Mail Number
You can enter, modify, or delete your voice mail number.
Note: Remember to add the + symbol and the appropriate country code prefix to
the phone number.
Service Centre
You can modify or delete it as desired. Remember to add the + symbol and the
appropriate country code prefix to the phone number.
Note: Before you can send messages, you need to enter your Message Service
Centre number provided by your service provider.
Expiry Period
Use to specify the maximum time, in hours, that your unforwarded messages remain
with the Message Service Centre before being deleted. he default is 24 hours. he
maximum value you can enter is 10584, although the real limit depends on your
Message Service Centre. 66
Phone Setup
Outgoing Message Type
his option is network dependent and can be used to specify the format of your
outgoing messages. You can select ext (default), Fax, X400, Paging, E-Mail, or
Voice. You do not need to select Voice to send messages to voice mail boxes.
Phone Setup
You can set custom alerts, the time and date, security codes, the contrast of your
display, and other features.
Select Phone Line
Allows you to switch between Line 1 and Line 2 of your Personal Communicator.
Note: Availability depends on the type and settings of the SIM card, and/or your
subscription to this feature.
Adjust Ring Volume
Use to increase or decrease the ringer volume of your Personal
Communicator.
67
Phone Setup
67
Ring or Vibrate
From the submenu, you can set your Personal Communicator to ring, vibrate, or
a combination of both. You can also set it to no ring or no vibrate to send and
receive SMS messages and Internet service messages in a silent mode. However,
when this option is selected, you will not be notified when you receive an incoming
voice call if the device is closed.
Set Ringer Tone
Use to select a musical alert or a standard ringing tone for incoming calls.
Set Ringer Tone 2
Use to select a tone alert for incoming calls on Line 2.
Note: his is a network and subscription dependent feature and may not be
available in all areas.
Set Alarm Ringer Tone
Use to turn the alarm alert ringer tone on or off.
Set Message Alert Tone
Use to set a musical alert or standard tone for incoming SMS messages.
68
Phone Setup
Edit Music Tone
Compose a musical alert and send it
via SMS Messaging to another
compatible Motorola phone. he alert
can have up to 35 notes and 3
octaves.
•A to G on the keyboard are musical notes A to G.
•R (rest) adds a pause. Press and hold R to extend
the length of the pause.
•Add a P between a note and the duration to change the pitch to either Flat or
Sharp. Add a P anywhere else to change the pitch for all notes.
• Change the duration of a note or rest by placing the cursor between the note
and the duration indicator, then enter a duration length: 1 is the shortest, 6 is the
longest and equals one second.
• Change the octave of the note by placing the cursor on the note and use ! to
increase or decrease it.
• You can also change the tempo of your tune to 1 (slowest), 4 (fastest), or 2 and
3 for somewhere in between.
Now you are ready to listen (play) to your new tune. If you like it, you can save it, or
go back and edit it or erase it and compose a new one.
A A a A C
G F G
A5 A5 a2 A2 G2 F2 G5 C5
r V iew O tions?
Edit Tone Example

69
Phone Setup
69
Send as an SMS Message
Impress your friends with your musical ability by sending your composed music
tone via an SMS message to another Motorola phone. If you receive a music
tone, you can play, save, or delete it.
Quick Access Setup
You can customise your Quick Access menu so you can quickly get to
the features you use the most. Refer to “Quick Access Menu” on
page 85 for usage and set up.
Phone Lock
You can lock your Personal Communicator to prevent others from using it.
Automatic Lock
When set to On, your Personal Communicator is locked automatically when it is
turned on. o use it, enter the unlock code.
Lock Now
Immediately locks your Personal Communicator from further use. o use it again,
enter the unlock code.
70
Phone Setup
Change Unlock Code
Use to change your unlock code. Follow the prompts given and enter a new
code. he code set by the manufacturer is 1234. If this code does not work,
check with your service provider.
Adjust Contrast
Lets you lighten or darken your display.
Require SIM Card PIN
When set to On, you need to enter your SIM card PIN each time it is inserted or your
Personal Communicator is turned on.
Note: his is not available if the SIM card does not support PIN code disabling.
How do I change my SIM card PIN? No problem, your Personal Communicator gives
you all the instructions.
Note: Be careful, if you enter your PIN incorrectly three times in a row, your
Personal Communicator locks up. See “Entering Your Unlock Code” on page 22 if
this happens.
Change SIM PIN2 Code
You can change your SIM PIN2 code just like your standard SIM code.
Note: his is a network and subscription dependent feature and may not be
available in all areas.
71
Phone Setup
71
Note: Be careful, your Personal Communicator locks up if the code is entered
incorrectly three times in a row.
Caution: If the PIN2 unblocking operation is performed incorrectly 10
times in a row, your PIN2 code becomes permanently blocked, please
see your service provider.
Unblocking Your V100 Personal Communicator
If you are blocked from accessing your V100 Personal Communicator, use the
following key sequence and the 8-digit PIN unblocking code that was provided by
your Cellular Service Provider to unblock it:
† † ‡ … † Unblock Code ( Ne PIN Code ( Ne PIN Code (
he new PIN code must contain four to eight digits.
Note: If this operation is performed incorrectly 10 times in a row, your SIM card will
become permanently blocked.
Ne Security Code
Enter the current security code, then a new six-digit code. he security code is set
by the manufacturer to 000000. If this code does not work, see your service
provider.
72
Phone Setup
Extended Menus
urn extended menus on or off. When Off, you are not able to access any of the
extended features.
Sho Time and Date
When selected, time and date is displayed until you press a button.
Set Time and Date
Setting the time and date is easy. Just follow the instructions given by your Personal
Communicator. But remember, use the international date format (day/month/year).
Set Time Format
You can change to either 12-hour or 24-hour format.
Language Selection
All prompts and help messages will be displayed in the language you select.
Battery Saving Mode
Set this to On to help your battery last longer. All status indicators and the backlight
for incoming Cell Broadcast messages are turned off.
Select Keypad Tones
You can set this so you hear tones when you press the buttons on your Personal
Communicator, or you can also turn off the tones.

73
Phone Setup
73
Phone Status
Status Review
When selected, your Personal Communicator displays a list of menu items which
have been changed from the default setting.
Master Reset
Please use this feature with caution because it restores certain options to their
default settings. his feature does the following:
• Cancels automatic answer, audible call timers, in-call display meter, battery
saver, auxiliary alert, automatic handsfree, automatic lock, and cell broadcast.
• Restores language selection, band selection, and extended menus to their
default settings.
• Restores keypad tones to normal, ringer tones to standard, SMS message alert
tones to standard, volume level to medium, and network search frequency to
medium.
74
Phone Setup
Master Clear
Note: All phone book entries are deleted with this option! Please use
it with caution.
he master clear option performs the same operations as the Master
Reset, but it also does the following:
• Clears phone book entries from memory (but not from SIM memory).
• Clears your list of all last calls made and received.
• Clears the message editor.
• Resets call timers.
• Erases all recorded voice notes and Voice ags.
Master Clear does not clear your:
• Fixed Dial list
• My Number list
• Charge meters
• Received and outgoing messages list
• Voice mail number
• Service Centre number
• Lifetime timer
75
Network Selection
75
Net ork Selection
o make and receive calls, your Personal Communicator must be registered with
one of the available networks.
Your Personal Communicator automatically searches for the last network used. If
this network is not available, your Personal Communicator attempts to register with
a different network.
When your Personal Communicator attempts to register with a different network, it
generates a sorted list of networks.
he network list is sorted in the following order:
• he Home network.
• Networks from a preferred list.
• A random list of other networks found above a certain signal strength.
• All remaining networks in descending order of signal strength.
Available Net orks
Use this to see which networks are operating in your area. When scanning
is complete, the list is displayed. When you find a network you want to
register with or store in your preferred list, press (. Follow the instructions given by
your Personal Communicator to register and store your selection.
76
Network Selection
Net ork Search
Determines how often your Personal Communicator attempts to
register with a network and how the attempt is made.
Registration Preferences
Set this to an automatic search (performed by your Personal Communicator) or to
manual search (performed by you).
• Automatic Search - Your Personal Communicator automatically generates a list
of networks and then tries to register with the first network in the list. If
registration fails, it tries to register with the next listed network. If registration
totally fails, it starts searching all over again.
• Manual Search - Your Personal Communicator gives you a list of networks to
choose from. If registration is successful, the network name is displayed. If
registration fails, the list is displayed again.
Frequency of Search
You can set the amount of time your Personal Communicator waits before trying to
re-register: slow, medium, fast, or continuous search.
Note: Fast and continuous search may use up a lot of battery power.