Motorola MVME712C Guide

[phone] | [email protected] | artisantg.com
-~
ARTISAN
®
~I
TECHNOLOGY
GROUP
Your definitive source
for
quality
pre-owned
equipment.
Artisan Technology
Group
Full-service,
independent
repair
center
with
experienced
engineers
and
technicians
on staff.
We
buy
your
excess,
underutilized,
and
idle
equipment
along
with
credit
for
buybacks
and
trade-ins
.
Custom
engineering
so
your
equipment
works
exactly as
you
specify.
•
Critical
and
expedited
services
•
Leasing
/
Rentals/
Demos
• In
stock/
Ready-to-ship
•
!TAR-certified
secure
asset
solutions
Expert
team
ITrust
guarantee
I
100%
satisfaction
All
tr
ademarks,
br
a
nd
names, a
nd
br
a
nd
s a
pp
earing here
in
are
th
e property of
th
e
ir
r
es
pecti
ve
ow
ner
s.
Find the Emerson / Motorola MVME712M / MVME712/M at our website: Click HERE

MVME712M
Transition Module
Installation and Use
VME712MA/IH2

Notice
While reasonable efforts have been made to assure the accuracy of this document,
Motorola, Inc. assumes no liability resulting from any omissions in this document, or from
the use of the information obtained therein. Motorola reserves the right to revise this
document and to make changes from time to time in the content hereof without obligation
of Motorola to notify any person of such revision or changes.
This material may be read online, downloaded for personal use, or included in another
document as a URL (from this server). The text itself may not be published commercially
in print or electronic form, edited or otherwise altered without the permission of Motorola,
Inc.
It is possible that this publication may contain reference to, or information about Motorola
products (machines and programs), programming, or services that are not announced in
your country. Such references or information must not be construed to mean that Motorola
intends to announce such Motorola products, programming, or services in your country.
Restricted Rights Legend
If the documentation contained herein is supplied, directly or indirectly, to the U.S.
Government, the following notice shall apply unless otherwise agreed to in writing by
Motorola, Inc.
Use, duplication, or disclosure by the Government is subject to restrictions as set forth in
subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at
DFARS 252.227-7013.
Motorola, Inc.
Computer Group
2900 South Diablo Way
Tempe, Arizona 85282

Preface
This manual, MVME712M Transition Module and P2 Adapter Board Installation and Use,
provides general information, hardware preparation, installation instructions, and support
information for the MVME712M Transition Module and the P2 Adapter Board.
The modules are used as the interface between the following families of Motorola
VMEmodules, and their peripheral devices:
A P2 adapter module and cable are supplied with the MVME712M.
This manual is intended for anyone who wants to design OEM systems, supply additional
capability to an existing compatible system, or in a lab environment for experimental
purposes. A basic knowledge of computers and digital logic is assumed.
To use this manual, you should be familiar with the publications inRelated Documentation.
MVME147 MPU VMEmodule MVME1600 Single Board Computer (SBC)
MVME162 Embedded Controller MVME2600 Single Board Computer (SBC)
MVME167 Single Board Controller (SBC) MVME2700 Single Board Computer (SBC)
MVME177 Single Board Controller (SBC) MVME3600 VME Processor Module
MVME4600 VME Processor Module

All Motorola PWBs (printed wiring boards) are manufactured by UL-recognized
manufacturers, with a flammability rating of 94V-0.
!
WARNING
This equipment generates, uses, and can radiate electro-
magnetic energy. It may cause or be susceptible to electro-
magnetic interference (EMI) if not installed and used in a
cabinet with adequate EMI protection.
Motorola®and the Motorola symbol are registered trademarks of Motorola, Inc.
PowerPCTM and VMEmoduleTM are trademarks of Motorola, Inc.
All other products mentioned in this document are trademarks or registered trademarks of
their respective holders.
© Copyright Motorola 1989, 1993, 1994, 1996, 1999
All Rights Reserved
Printed in the United States of America
April 1999
European Notice: Board products with the CE marking comply with the EMC
Directive (89/336/EEC). Compliance with this directive implies conformity to the
following European Norms:
EN55022 (CISPR 22) Radio Frequency Interference
EN50082-1 (IEC801-2, IEC801-3, IEEC801-4) Electromagnetic Immunity
The product also fulfills EN60950 (product safety) which is essentially the
requirement for the Low Voltage Directive (73/23/EEC).
This board product was tested in a representative system to show compliance with
the above mentioned requirements. A proper installation in a CE-marked system
will maintain the required EMC/safety performance.

Safety Summary
Safety Depends On You
The following general safety precautions must be observed during all phases of operation, service, and repair of this
equipment. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety
standards of design, manufacture, and intended use of the equipment. Motorola, Inc. assumes no liability for the
customer’s failure to comply with these requirements.
The safety precautions listed below represent warnings of certain dangers of which Motorola is aware. You, as the user
of the product, should follow these warnings and all other safety precautions necessary for the safe operation of the
equipment in your operating environment.
Ground the Instrument.
To minimize shock hazard, the equipment chassis and enclosure must be connected to an electrical ground. The
equipment is supplied with a three-conductor ac power cable. The power cable must be plugged into an approved
three-contact electrical outlet. The power jack and mating plugof the power cable meet International Electrotechnical
Commission (IEC) safety standards.
Do Not Operate in an Explosive Atmosphere.
Do not operate the equipment in the presence of flammable gases or fumes. Operation of any electrical equipment in
such an environment constitutes a definite safety hazard.
Keep Away From Live Circuits.
Operating personnel must not remove equipment covers. Only Factory Authorized Service Personnel or other
qualified maintenance personnel may remove equipment covers for internal subassembly or component replacement
or any internal adjustment. Do not replace components with power cable connected. Under certain conditions,
dangerous voltages may exist even with the power cable removed. To avoid injuries, always disconnect power and
discharge circuits before touching them.
Do Not Service or Adjust Alone.
Do not attempt internal service or adjustment unless another person capable of rendering first aid and resuscitation is
present.
Use Caution When Exposing or Handling the CRT.
Breakage of the Cathode-Ray Tube (CRT) causes a high-velocity scattering of glass fragments (implosion). To prevent
CRT implosion, avoid rough handling or jarring of the equipment. Handling of the CRT should be done only by
qualified maintenance personnel using approved safety mask and gloves.
Do Not Substitute Parts or Modify Equipment.
Because of the danger of introducing additional hazards, do not install substitute parts or perform any unauthorized
modification of the equipment. Contact your local Motorola representative for service and repair to ensure that safety
features are maintained.
Dangerous Procedure Warnings.
Warnings, such as the example below, precede potentially dangerous procedures throughout this manual. Instructions
contained in the warnings must be followed. You should also employ all other safety precautions which you deem
necessary for the operation of the equipment in your operating environment.
!
WARNING
Dangerous voltages, capable of causing death, are present in
this equipment. Use extreme caution when handling, testing,
and adjusting.

vii
Contents
CHAPTER 1 General Information
Introduction................................................................................................................1-1
Description.................................................................................................................1-1
MVME712M Transition Module........................................................................1-2
P2 Adapter Board................................................................................................1-2
Specifications.............................................................................................................1-3
Cooling Requirements ...............................................................................................1-4
FCC Compliance........................................................................................................1-5
Related Documentation..............................................................................................1-6
MCG Customer Services ...........................................................................................1-7
CHAPTER 2 Preparing and Installing the Hardware
Introduction................................................................................................................2-1
Unpacking the Hardware ...........................................................................................2-1
Preparing the MVME712M Module..........................................................................2-2
DTE/DCE configuration select headers..............................................................2-2
Serial port 1 DCE configuration -- J1 and J11 ............................................2-4
Serial port 1 DTE configuration -- J1 and J11.............................................2-5
Serial port 2 DCE configuration -- J16 and J17 ..........................................2-6
Serial port 2 DTE configuration -- J16 and J17...........................................2-7
Serial port 3 DCE configuration -- J13 and J14 ..........................................2-8
Serial port 3 DTE configuration - J13 and J14............................................2-9
Serial port 4 DCE configuration -- J18 and J19 ........................................2-10
Serial port 4 DTE configuration - J18 and J19..........................................2-11
Serial port 4 clock configuration select header -- J15 ...............................2-12
SCSI Termination......................................................................................2-13
Preparing the P2 Adapter Board ..............................................................................2-14
Cables and Connectors.............................................................................................2-15
Installing the MVME712M Module and P2 Adapter Board ...................................2-17
Procedure..........................................................................................................2-17
Configuration A - Internal SCSI Devices Only................................................2-19
Configuration B - Internal SCSI Devices Only ................................................2-21
Configuration B1 - Internal SCSI Devices Only ..............................................2-23
Configuration C - Internal and External SCSI Devices....................................2-25
Configuration C1 - Internal and External SCSI Devices..................................2-28

viii
Configuration D - Internal and External SCSI Devices ...................................2-30
Configuration E - External SCSI Devices Only...............................................2-33
Configuration F - External SCSI Devices Only ...............................................2-35
CHAPTER 3 Interconnect Signals
Introduction ...............................................................................................................3-1
P2 Adapter Board ......................................................................................................3-2
P2 connector.......................................................................................................3-2
J2 connector .......................................................................................................3-2
J3 connector........................................................................................................3-7
MVME712M Transition Module ..............................................................................3-9
J2 connector .......................................................................................................3-9
J3 and J4 connectors.........................................................................................3-14
SCSI interface connector..................................................................................3-16
J5 connector......................................................................................................3-18
J6 connector......................................................................................................3-19
J7 - J10 connectors ...........................................................................................3-20
J20 connector....................................................................................................3-21
J21 connector....................................................................................................3-22

ix
List of Figures
Figure 2-1. MVME712M header locations................................................................2-3
Figure 2-2. Serial port 1 configured as DCE .............................................................2-4
Figure 2-3. Serial port 1 configured as DTE..............................................................2-5
Figure 2-4. Serial port 2 configured as DCE .............................................................2-6
Figure 2-5. Serial port 2 configured as DTE..............................................................2-7
Figure 2-6. Serial port 3 configured as DCE .............................................................2-8
Figure 2-7. Serial port 3 configured as DTE..............................................................2-9
Figure 2-8. Serial port 4 configured as DCE ...........................................................2-10
Figure 2-9. Serial port 4 configured as DTE............................................................2-11
Figure 2-10. J15 clock line configuration................................................................2-12
Figure 2-11. P2 adapter connector locations............................................................2-14
Figure 2-12. Configuration A -- internal-only SCSI connections............................2-20
Figure 2-13. Configuration B -- internal-only SCSI connections............................2-22
Figure 2-14. Configuration B1 -- internal-only SCSI connections..........................2-24
Figure 2-15. Configuration C -- internal and external SCSI connections................2-27
Figure 2-16. Configuration C1 -- internal and external SCSI connections..............2-29
Figure 2-17. Configuration D -- internal and external SCSI connections................2-32
Figure 2-18. Configuration E -- external-only SCSI connections............................2-34
Figure 2-19. Configuration F -- external-only SCSI connections............................2-37

xi
List of Tables
Table 1-1. MVME712M specifications......................................................................1-3
Table 2-1. Serial port jumpers/headers ......................................................................2-2
Table 2-2. VMEmodule headers/switches ...............................................................2-12
Table 2-3. Cables and connectors ..........................................................................2-15
Table 2-4. Cabling configurations............................................................................2-18
Table 3-1. P2 adapter board and MVME712M connectors.......................................3-1
Table 3-2. Connector J2 interconnect signals ...........................................................3-2
Table 3-3. Connector J3 interconnect signals ...........................................................3-7
Table 3-4. Connector J2 interconnect signals ...........................................................3-9
Table 3-5. Connectors J3 and J4 interconnect signals ............................................3-14
Table 3-6. Connector SCSI interface interconnect signals ......................................3-16
Table 3-7. Connector J5 interconnect signals .........................................................3-18
Table 3-8. Connector J6 interconnect signals .........................................................3-19
Table 3-9. Connectors J7 - J10 interconnect signals ...............................................3-20
Table 3-10. Connector J20 interconnect signals .....................................................3-21
Table 3-11. Connector J21 interconnect signals .....................................................3-22