Motorola M68MPB16Z3 User manual

M68MPB16Z3UM/D
February 1998
M68MPB16Z3
MCU PERSONALITY BOARD
USER’S MANUAL
© MOTOROLA, INC., 1994, 1998; All Rights Reserved

Motorola reserves the right to make changes without further notice to any products herein to
improve reliability, function or design. Motorola does not assume any liability arising out of the
application or use of any product or circuit described herein; neither does it convey any license
under its patent rights nor the rights of others. Motorola products are not designed, intended, or
authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of
the Motorola product could create a situation where personal injury or death may occur. Should
Buyer purchase or use Motorola products for any such unintended or unauthorized application,
Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and
distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney
fees arising out of, directly or indirectly, any claim of personal injury or death associated with
such unintended or unauthorized use, even if such claim alleges that Motorola was negligent
regarding the design or manufacture of the part.
Motorola and the Motorola logo are registered trademarks of Motorola Inc.SDI is a trademark of
Motorola Inc.
Motorola Inc. is an Equal Opportunity/Affirmative Action Employer.

CONTENTS
M68MPB16Z3UM/D iii
CONTENTS
CHAPTER 1 GENERAL INFORMATION
1.1 INTRODUCTION.............................................................................................................. 1-1
1.2 SPECIFICATIONS............................................................................................................. 1-2
1.3 EQUIPMENT REQUIRED................................................................................................ 1-2
1.4 CUSTOMER SUPPORT.................................................................................................... 1-3
CHAPTER 2 HARDWARE PREPARATION AND INSTALLATION
2.1 INTRODUCTION.............................................................................................................. 2-1
2.2 HARDWARE PREPARATION......................................................................................... 2-1
2.2.1 Clock Select Header (W1)......................................................................................... 2-4
2.2.2 VDDA Select Header (W2)....................................................................................... 2-5
2.2.3 Voltage Reference High Select Header (W3)............................................................ 2-6
2.2.4 Voltage Reference Low Select Header (W4)............................................................. 2-7
2.2.5 MCU ID Code Select Header (W6, W7, W8, W9, W10).......................................... 2-8
2.2.6 VSSA Insertion Point (E1) ........................................................................................ 2-8
2.3 MEVB CONFIGURATION............................................................................................... 2-9
2.4 ACTIVE PROBE CONFIGURATION............................................................................ 2-11
CHAPTER 3 MEVB QUICK START GUIDE
3.1 INTRODUCTION.............................................................................................................. 3-1
3.2 CONFIGURING THE MPFB............................................................................................. 3-1
3.2.1 MPFB Memory Devices............................................................................................ 3-1
3.2.2 MPFB Jumper Headers.............................................................................................. 3-2
3.3 MEVB INSTALLATION INSTRUCTIONS..................................................................... 3-3
3.3.1 Power Supply – MPFB Connection........................................................................... 3-4
3.3.2 Personal Computer – BDM Connection.................................................................... 3-5
3.4 SOFTWARE INSTALLATION AND MCU INITIALIZATION...................................... 3-5

CONTENTS
iv M68MPB16Z3UM/D
CHAPTER 4 MEVB SUPPORT INFORMATION
4.1 INTRODUCTION.............................................................................................................. 4-1
4.2 LOGIC ANALYZER CONNECTOR SIGNALS............................................................... 4-1
CHAPTER 5 MAPI SUPPORT INFORMATION
5.1 INTRODUCTION.............................................................................................................. 5-1
5.2 MAPI BUS CONNECTORS.............................................................................................. 5-1
CHAPTER 6 SCHEMATIC DIAGRAMS
6.1 INTRODUCTION.............................................................................................................. 6-1
FIGURES
2-1. MPB Parts Location Diagram (top view)........................................................................... 2-2
2-2. MPB – MPFB Interconnection (with SDI interface connector) ....................................... 2-10
2-3. Active Probe Interconnection (with Active Probe Box)................................................... 2-12
5-1. MAPI Interface Connector Layout...................................................................................... 5-1
5-2. MAPI Interface Connector P1 Pin Assignments................................................................ 5-2
5-3. MAPI Interface Connector P2 Pin Assignments................................................................ 5-3
5-4. MAPI Interface Connector P3 Pin Assignments................................................................ 5-4
5-5. MAPI Interface Connector P4 Pin Assignments................................................................ 5-5
TABLES
1-1. MPB Specifications............................................................................................................ 1-2
2-1. Jumper Header Types......................................................................................................... 2-3
2-2. MPB Jumper Header Descriptions ..................................................................................... 2-3
3-1. MPFB Quick Start Jumper Header Configuration.............................................................. 3-2
4-1. Logic Analyzer Connector J7 Pin Assignments................................................................. 4-2
4-2. Logic Analyzer Connector J8 Pin Assignments................................................................. 4-2
4-3. Logic Analyzer Connector J9 Pin Assignments................................................................. 4-3
4-4. Logic Analyzer Connector J10 Pin Assignments............................................................... 4-3
4-5. Logic Analyzer Connector J11 Pin Assignments............................................................... 4-4
4-6. Logic Analyzer Connector J12 Pin Assignments............................................................... 4-4

CONTENTS
M68MPB16Z3UM/D v
TABLES (continued)
4-7. Logic Analyzer Connector J13 Pin Assignments............................................................... 4-6
4-8. Logic Analyzer Connector J14 Pin Assignments............................................................... 4-8
4-9. Logic Analyzer Connector J15 Pin Assignments ............................................................... 4-9
4-10.Logic Analyzer Connector J16 Pin Assignments............................................................... 4-9
4-11.Logic Analyzer Connector J17 Pin Assignments............................................................. 4-10
4-12.Logic Analyzer Connector J18 Pin Assignments............................................................. 4-11
4-13.Logic Analyzer Connector J19 Pin Assignments............................................................. 4-12
4-14.Logic Analyzer Connector J20 Pin Assignments............................................................. 4-12

CONTENTS
vi M68MPB16Z3UM/D

GENERAL INFORMATION
M68MPB16Z3UM/D 1-1
CHAPTER 1
GENERAL INFORMATION
1.1 INTRODUCTION
This manual provides general information, hardware preparation, installation
instructions, a quick start guide, support information, and schematic diagrams for
the M68MPB16Z3 MCU Personality Board (MPB). The MPB is one component
of Motorola’s modular approach to MC68HC16Z3 Microcontroller Unit-based
product development. This modular approach lets you easily configure our
development systems to fit your requirements.
The MPB may be used in either the MMDS1632 Motorola Modular Development
System (MMDS) or the modular evaluation board (MEVB). The MEVB consists
of the M68MPFB Modular Platform Board (MPFB) and an MPB. Alternately, you
may install the MPB directly in your target system if the target system includes a
modular active probe interconnect (MAPI) interface. The MCU device on the
MPB defines which MCU is emulated/evaluated by the MMDS or evaluated by
the MEVB. Both systems are invaluable tools for designing, debugging, and
evaluating MCU operation of the M68HC12, M68HC16, and M68300 MCU
families. By providing the essential MCU timing and I/O circuitry, these systems
simplify user evaluation of prototype hardware/software products.
The MPB includes:
• M68MPB16Z3 MCU Personality Board (MPB)
• Plastic overlay for use with the MEVB – pin outs for the logic analyzer
connectors on the MPFB (the overlay for this MPB is the same one used
with the M68MPB16Z1)
• Documentation (this manual)

GENERAL INFORMATION
1-2 M68MPB16Z3UM/D
1.2 SPECIFICATIONS
Table 1-1 lists MPB specifications.
Table 1-1. MPB Specifications
Characteristic Specifications
On-Board Clock Case style: 14- or 8-pin hybrid crystal clock oscillator
(frequency as required by MCU).
External Clock 32 KHz – 16.78 MHz (or maximum MCU allows).
MCU I/O ports HCMOS compatible
Temperature
Operating
Storage 0° to +40° C -40° to +85° C
Relative humidity 0 to 90% (non-condensing)
Power requirements +5Vdc ± 5% @ 500 mA (max.)
Dimensions
MCU Personality Board 3.25 x 3.25 in. (82.6 x 82.6 mm)
1.3 EQUIPMENT REQUIRED
The external requirements for MPB operation are either an MEVB or MMDS
system. For MMDS operation requirements, see the MMDS1632 Motorola
Modular Development System User’s Manual,MMDS1632UM/D. For operation
requirements for the MEVB, see this manual and the M68MPFB Modular
Platform Board User’s Manual,M68MPFBUM/D.

GENERAL INFORMATION
M68MPB16Z3UM/D 1-3
1.4 CUSTOMER SUPPORT
For information about a Motorola distributor or sales office near you call:
AUSTRALIA, Melbourne – (61-3)887-0711
Sydney – 61(2)906-3855
BRAZIL, Sao Paulo – 55(11)815-4200
CANADA, B. C., Vancouver – [phone]
ONTARIO, Toronto – [phone]
ONTARIO, Ottawa – [phone]
QUEBEC, Montreal – [phone]
CHINA, Beijing – 86-10-68437222
DENMARK – (45)43488393
FINLAND, Helsinki – 358-9-6824-400
FRANCE, Paris – 33134 635900
GERMANY,
Langenhagen/Hannover – 49(511)786880
Munich – 49 89 92103-0
Nuremberg – 49 911 96-3190
Sindelfingen – 49 7031 79 710
Wiesbaden – 49 611 973050
HONG KONG, Kwai Fong – 852-6106888
Tai Po – 852-6668333
INDIA, Bangalore – (91-80)5598615
ISRAEL, Herzlia – 972-9-590222
ITALY, Milan – 39(2)82201
JAPAN, Fukuoka – 81-92-725-7583
Gotanda – 81-3-5487-8311
Nagoya – 81-52-232-3500
Osaka – 81-6-305-1802
Sendai – 81-22-268-4333
Takamatsu – 81-878-37-9972
Tokyo – 81-3-3440-3311
KOREA, Pusan – 82(51)4635-035
Seoul – 82(2)554-5118
MALAYSIA, Penang – 60(4)2282514
MEXICO, Mexico City – 52(5)282-0230
Guadalajara – 52(36)21-8977
PUERTO RICO, San Juan – [phone]
SINGAPORE – (65)4818188
SPAIN, Madrid – 34(1)457-8204
SWEDEN, Solna – 46(8)734-8800
SWITZERLAND, Geneva – 41(22)799 11 11
Zurich – 41(1)730-4074
TAIWAN, Taipei – 886(2)717-7089
THAILAND, Bangkok – 66(2)254-4910
UNITED KINGDOM, Aylesbury – 441(296)395-252
UNITED STATES, Phoenix, AZ – 1-800-441-2447
For a list of the Motorola sales offices and distributors:
0http://www.mcu.motsps.com/sale_off.html

GENERAL INFORMATION
1-4 M68MPB16Z3UM/D