Motorola AP6522 User manual

AP6522 Access Point
INSTALLATION GUIDE

2 AP6522 Access Point
MOTOROLA SOLUTIONS and the Stylized M Logo are registered in the US Patent & Trademark Office. © Motorola Solutions,
Inc. 2012. All rights reserved.

Installation Guide 3
1.0 Introduction ......................................................4
1.1 Document Conventions ...............................................4
1.2 Warnings ..........................................................5
1.3 Site Preparation ....................................................5
1.4 AP6522 Package Contents.............................................5
2.0 Hardware Installation ..............................................7
2.1 Installation Instructions ............................................... 7
2.2 Precautions ........................................................ 8
2.3 Access Point Placement............................................... 8
2.4 Integrated Antenna Model Wall Mount Instructions ........................ 8
2.5 Integrated Antenna Model Suspended Ceiling T-Bar Mount ................. 11
2.6 External Antenna Model Wall Mount Instructions ......................... 12
2.7 External Antenna Model Suspended Ceiling T-Bar Mount ................... 15
2.8 External Antenna Suspended Ceiling Tile (Plenum) Mount .................. 17
2.9 AP6522 External Antenna Model Antenna Options ........................ 18
2.10 LED Indicators .................................................... 20
3.0 Initial Access Point Configuration .................................. 22
4.0 Specifications.................................................... 38
4.1 AP6522 Integrated Antenna Model Electrical Characteristics ................ 38
4.2 AP6522 Integrated Antenna Model Physical Characteristics ................. 38
4.3 AP6522 External Antenna Model Electrical Characteristics .................. 39
4.4 AP6522 External Antenna Model Physical Characteristics................... 39
4.5 Radio Characteristics................................................ 40
5.0 Regulatory Information ............................................ 41
6.0 Part Numbers, Support and Sales ................................... 49
7.0 Motorola Solutions, Inc. End-User License Agreement ................ 50
8.0 AP6522 Access Point China ROHS Compliance ...................... 53

4 AP6522 Access Point
1 Introduction
The AP6522 access point, a component of the Motorola Solutions wireless controller system, links wireless
802.11abgn devices to the controller, enabling the growth of your wireless network with a cost effective
alternative to standard access points. The AP6522 access point provides multiple deployment options.
The AP6522 access point receives all power and transfers data through the same CAT-5 or better Ethernet cable.
An 802.3af Ethernet switch or power supply (specifically rated for the AP6522) is required (Part No.
PWRS-14000-148R).
An AP6522 model access point uses WiNG 5 software as its onboard operating system. The access point’s unique
WiNG 5 software enables the access point to function as either a Virtual Controller AP capable of adopting and
managing up to 24 additional AP6522 access points, a Standalone access point or a Dependent mode access point
managed by its connected controller.
If new to Motorola Solutions access point technology, refer to the WiNG Access Point System Reference Guide to
familiarize yourself with access point technology and the feature set supported by the WiNG operating system.
The guide is available, at http://supportcentral.motorola.com/support/product/manuals.do.
The AP6522 access point is approved under MODEL: AP-0622.
This document is written for the qualified network device installer.
1.1 Document Conventions
The following graphical alerts are used in this document to indicate notable situations:
NOTE Tips, hints, or special requirements that you should take note of.
CAUTION Care is required. Disregarding a caution can result in data loss or
equipment malfunction.
WARNING! Indicates a condition or procedure that could result in personal injury or
equipment damage.
!

Installation Guide 5
1.2 Warnings
• Read all installation instructions and site survey reports, and verify correct equipment installation before
connecting the access point.
• Remove jewelry and watches before installing this equipment.
• Verify the unit is grounded before connecting it to the power source.
• Verify any device connected to this unit is properly wired and grounded.
• Verify there is adequate ventilation around the device, and that ambient temperatures meet equipment
operation specifications.
1.3 Site Preparation
• Consult your site survey and network analysis reports to determine specific equipment placement, power
drops, and so on.
• Assign installation responsibility to the appropriate personnel.
• Identify and document where all installed components are located.
• Ensure adequate, dust-free ventilation to all installed equipment.
• Identify and prepare Ethernet and console port connections.
• Verify cable lengths are within the maximum allowable distances for optimal signal transmission.
1.4 Package Contents
An AP6522 access point is available in integrated antenna and external antenna models. Contents differ
depending on the model ordered.
1.4.1 External Antenna Model Package Contents
• AP6522 access point with external antenna connectors (Plenum Rated)
• 2 customer installed mounting lugs
• 4 mounting lug retaining screws
• AP6522 Installation Guide (This Guide)
1.4.2 Internal Antenna Model Package Contents
• AP6522 access point with internal antennas
• AP6522 Installation Guide (This Guide)

6 AP6522 Access Point
1.4.3 Features
• 2 RJ-45 connectors, one for 10/100/1000 Ethernet and the other for the serial/console connector
• LED indicators
• Slots for wall mounting
• Clips for mounting on a suspended ceiling T-bar (internal antenna model only) with separately orderable
accessories
• Lock port for Kensington® style Security Lock
The AP6522 access point has one RJ-45 connector supporting an 10/100/1000 Ethernet port and accepts
802.3af-compliant power from an external source. The illustration below is of an integrated antenna model.
The AP6522 access point comes with dual radios supporting 802.11abgn. The access point contains runtime
firmware which enables the unit to boot after a power up. The runtime firmware on the access point and the
firmware downloaded from the connected controller can be updated via the Ethernet interface.
NOTE When operating in a Gigabit Ethernet environment, CAT-5e or CAT-6 cable
is recommended for Gigabit operation.
NOTE When connecting to an AP6522 model access point, note that the baud
rate is 115,200 as opposed to 19,200.
DC12V GE1/PoE Console

Installation Guide 7
2 Hardware Installation
2.1 Installation Instructions
The AP6522 access point mounts either on a wall (with customer supplied M4 x 25 pan head screws and wall
anchor - or equivalent) or on a suspended ceiling T-bar. If deploying an external antenna model AP6522 on a
suspended ceiling T-bar, access point mounting kit (Part No. KT-135628-01) is required. An AP6522 is not designed
for mounting on a desk.
To prepare for the installation:
1. Match the model number on the purchase order with the model numbers in the packing list and on the
case of the access point.
2. Verify the contents of the box include the intended AP6522 access point, and the included hardware
matches the package contents on page 5.
3. Review site survey and network analysis reports to determine the location and mounting position for the
AP6522 access point.
4. Connect a CAT-5 or better Ethernet cable to a compatible 802.3af power source and run the cable to the
installation site. Ensure there is sufficient slack on the cable to perform the installation steps.
Part Number Description
AP-6522-66030-US Dual 802.11n radio AP6522. Plastic enclosure with internal antennas.
For use in the US deployments only.
AP-6522-66030-EU Dual 802.11n radio AP6522. Plastic enclosure with internal antennas.
For use in European countries only.
AP-6522-66030-WR Dual 802.11n radio AP6522. Plastic enclosure with internal antennas.
For use in non-US countries only.
AP-6522-66040-US Dual 802.11n radio AP6522. Metal enclosure with external antenna
connectors. For use in US deployments only.
AP-6522-66040-EU Dual 802.11n radio AP6522. Metal enclosure with external antenna
connectors. For use in European countries only.
AP-6522-66040-WR Dual 802.11n radio AP6522. Metal enclosure with external antenna
connectors. For use in non-US countries only.
NOTE When operating in a Gigabit Ethernet environment, CAT-5e or CAT-6 cable
is recommended for Gigabit operation.

8 AP6522 Access Point
2.2 Precautions
Before installing an AP6522 model Access Point, verify the following:
• If a DC power supply is used, ensure it’s the approved power supply for the AP6522 (PWRS-1400-148R).
• Motorola Solutions recommends you do not to install the AP6522 in wet or dusty areas.
• Verify the environment has a continuous temperature range between 0° C to 40° C.
2.3 Access Point Placement
For optimal performance, install the access point away from transformers, heavy-duty motors, fluorescent lights,
microwave ovens, refrigerators and other industrial equipment. Signal loss can occur when metal, concrete, walls
or floors block transmission. Install the access point in an open area or add access points as needed to improve
coverage.
Antenna coverage is analogous to lighting. Users might find an area lit from far away to be not bright enough. An
area lit sharply might minimize coverage and create dark areas. Uniform antenna placement in an area (like even
placement of a light bulb) provides even, efficient coverage.
Place the access point using the following guidelines:
• Install the access point at an ideal height of 10 feet from the ground.
• Orient the access point antennas vertically for best reception (applies to external antenna models only).
To maximize the access point’s radio coverage area, Motorola Solutions recommends conducting a site survey to
define and document radio interference obstacles before installing the access point.
2.4 Integrated Antenna Model Wall Mount Instructions
Wall mounting requires hanging the AP6522 along its width or length using the two slots on the bottom of the unit.
The AP6522 can be mounted on to any plaster, wood, or cement wall surface using customer supplied screw
hardware (M3.5 x 0.6 x 20 mm- or equivalent).
2.4.1 Wall Mount Hardware
• Two wide-shoulder Phillips pan head self-tapping screws (customer supplied)
• Two wall anchors (customer supplied)
• Security cable (optional)
NOTE The following screws are recommended: (ANSI Standard) #6-18 X
0.875in. Type A or AB Self-Tapping Screw, or (ANSI Standard Metric)
M3.5 X 0.6 X 20mm Type D Self-Tapping Screw.

Installation Guide 9
2.4.2 Wall Mount Procedure
1. Orient the case on the wall by its width or length.
CAUTION To ensure proper operation of an AP6522 access point, ensure it is
mounted in the correct orientation as shown above.
!

10 AP6522 Access Point
2. Mark two points (for drill holes) 4.08 inches (103.7 mm) apart on a horizontal line.
3. At each point, drill a hole in the wall, insert an anchor, screw into the anchor the wall mounting screw and
stop when there is 1mm between the screw head and the wall.
4. If required, install and attach a Kensington security cable (customer supplied) to the unit’s lock port.
5. Attach an Ethernet cable from the access point to a controller with an 802.3af-compatible power source
or use the PWRS-14000-148R power supply to supply power to the AP6522 (once fully cabled).
6. Place the middle of each of the case’s mount slots over the screw heads.
7. Slide the case down along the mounting surface to hang the mount slots on the screw heads.
8. Verify the unit has power by observing that the LEDs are lit or flashing.
NOTE When pre-drilling a hole the recommended hole size is 2.8mm (0.11in.).
CAUTION If not using a 802.3af capable controller to power the AP6522, ensure
only the AP6522’s designated power supply (PWRS-14000-148R) is
used to supply power to the access point. Using an incorrectly rated
power supply could damage the unit and void the product warranty.
Do not actually connect to the power source until the cabling portion
of the installation is complete.
!