Mountz BLG-4000 User manual

BLG-Series Operating Instructions
Corporate Headquarters: 1080 North 11th Street, San Jose, CA 95112 Phone: [phone] Fax: [phone]
www.mountztorque.com
Rev 1.0 (5/13/13)

BLG-Series Operating Instructions
Corporate Headquarters: 1080 North 11th Street, San Jose, CA 95112 Phone: [phone] Fax: [phone]
www.mountztorque.com
Name of Parts
BLG-4000 (lever start BLG-5000 (Lever or Push Start) Selectable by the Switch
Power tool cable
Knurled ground ring
Hanger
Joint ring FOR/REV switch
FOR: Forward
OFF: Neutral
REV: Reverse
Bit
Switch lever
Torque adjust-
ment scale
Joint shaft collar
Torque adjust-
ment nut
Protective cover
for the torque
adjustment nut
(be removed by
turning it CCW)
Protective cover for
the torque
adjustment nut can
be removed
by
turning
it anti-clockwise
Two-way Start System (Switchable between
Lever Start and Push-to-Start)
Marking between “Lever” and
“Push”start selection.
L  P
See page 3, how to do it.
Power tool cable
Hanger
FOR/REV switch
FOR: Forward
OFF: Neutral
REV: Reverse
Driver
connector
Switch lever
Torque
adjustment scale
Bit
Joint shaft collar
Transformer Guide
Model Item # For Use with Electric Screwdriver Models
T-30BL 144300 BLG4000X
T-70BL 144400 BLG4000X - BLG5000X
T-70BL T-30BL
Page 2

Operating the BLG-4000 Model
1. Attach power tool cable to the BLG-4000 screwdriver and the transformer. Make sure notch in plug lines up
with the notch on the socket. Tighten knurled ground ring.
2. Plug in power cord to the back of the transformer and power outlet. Flip power switch to “ON” position
located on the front of transformer.
3. Select a bit. Retract the bit collar. Insert the bit and release the retracted collar. To avoid damaging
fasteners, make sure the proper bit is suitable for the head of the fastener.
4. The torque limit is determined by the tension of the coil spring housed in the torque adjustment nut. The
tighter the coil spring is wound the higher the torque limit is raised. See Torque Charts on page 4 to
determine the appropriate torque adjustment setting.
5. Rotate the torque adjustment nut to set the torque limit. Turn clockwise to increase torque and counter
clockwise to decrease torque. The scale adjacent to the Torque Adjustment Nut is a reference guide. The
torque output from the driver can change depending on various fastening factors like friction, type of joint,
and the type material being used like a washer. Verify torque setting with a torque testing system.
6. Turn driver on and check for proper rotation. FOR-clockwise, REV-counterclockwise.
7. To apply torque, squeeze the lever. The driver will automatically stop when the preset torque has been
reached.
8. To remove the screw, turn the FOR/REV switch to REV position.
BLG-Series Operating Instructions
Corporate Headquarters: 1080 North 11th Street, San Jose, CA 95112 Phone: [phone] Fax: [phone]
www.mountztorque.com
Torque adjustment nut
Operating the BLG-5000 Model
1. Attach power tool cable to the BLG-5000 screwdriver and the transformer. Make sure notch in plug lines up
with the notch on the socket. Tighten knurled ground ring.
2. Plug in power cord to the back of the transformer and power outlet. Flip power switch to “ON” position
located on the front of transformer.
3. Select a bit. Retract the bit collar. Slide the bit collar forward. Insert the bit and release the retracted
collar. To avoid damaging fasteners, make sure the proper bit is suitable for the head of the fastener.
4. The torque limit is determined by the tension of the coil spring housed in the tool. The
tighter the coil spring is wound the higher the torque limit is raised. See Torque Charts on page 4 to
determine the appropriate torque adjustment setting.
5. Using the “Hex Key wrench”, set the torque referring to the torque adjustment scale “1 to 8”. Turn
clockwise to increase torque and counter clockwise to decrease torque. The torque adjustment scale
is a reference guide. The torque output from the driver can change depending on various fastening
factors like friction, type of joint, and the type material being used like a washer. Verify torque setting
with a torque testing system.
6. Turn driver on and check for proper rotation. FOR-clockwise, REV-counterclockwise.
7. To apply torque, squeeze the lever (If Push-to-Start setting is set-up for the BLG-5000* model - place
light downward pressure on the nose of the driver). The driver will automatically stop when the preset torque has been
reached.
8. To remove the screw, turn the FOR/REV switch to REV position.
* Note: The BLG-5000 features a two-way start system (switchable between Lever
Start and Push-to-Start)
How to Change BLG-5000 to “Push” Start System
1. Unscrew the “switch lever shaft screw” and then take off the “switch lever”. Using
tweezers, move the selection SW near “P” (push) mark.
* Note: Do not press or hit the SW or you may damage the SW or body case.
Torque
adjustment
scale
Hex Key Wrench
Switch lever
shaft screw
Page 3
Switch lever
Slide switch
between L or P

Corporate Headquarters: 1080 North 11th Street, San Jose, CA 95112 Phone: [phone] Fax: [phone]
www.mountztorque.com
BLG-Series Operating Instructions
Torque Reference Charts
These charts are meant to be used as guidelines for setting the torque on the BLG-Series electric screwdrivers. The drivers
have a torque adjustment scale showing reference numbers. These numbers determine the approximate torque setting. Refer
to the charts to determine the reference number setting for your torque requirement.
How to Read the Torque Charts
Torque ranges (lbf.in) approximate tightening torque, operated with no load at maximum speed. Verify torque setting with a
torque testing system.
BLG-4000
1 2 3 4 5 6
Torque Scale
0.5
1
1.5
2
2.5
3
3.5
4
lbf.in
7
R (Red)
Torque Range
1.8 - 4.8 lbf.in
4.5
5
5.5
8
BLG-5000
1 2 3 4 5 6
Torque Scale
1
2
3
4
5
6
7
8
lbf.in
7
S (Silver)
Torque Range
1.7 - 10 lbf.in
9
10
11
8
W (White)
Torque Range
0.9 - 2.7 lbf.in
Page 4

Corporate Headquarters: 1080 North 11th Street, San Jose, CA 95112 Phone: [phone] Fax: [phone]
www.mountztorque.com
Testing Power Tools:
1. Application Method: Use a torque tester in “Peak Mode” with a rotary torque sensor between the power tool and the actual
application. This is the best way to test since you are using the actual joint as the test station. You will see the actual
torque applied to the fastener. Caution: Variances in tool performance may occur do to the addition of the rotary torque sensor.
2. Simulated Method: Always use a quality joint rate simulator (run down adapter) with a torque tester when testing power
tools in a simulated application. Use Joint rate and Breakaway methods to obtain most accurate torque readings in a
simulated rundown.
Care
1. The BLG-Series screwdrivers are a precision torque control instrument and should be handled with care at all times.
2. Only use the transformers listed in the Mountz catalog or website for appropriate BLG-Series driver model (If you have any questions
regarding the appropriate transformer set-up, contact Mountz Customer Service Department).
3. Operate under safe conditions. Do not place in operation where such objects as hair, strings, clothing, etc. can become
tangled in the rotating bit.
4. Keep away from moisture. Never use in high humid, moist or damp environment.
Mountz Calibration & Repair Services
Mountz Inc. features an experienced calibration and repair staff. Our trained technicians can calibrate and repair most any tool. Mountz pro-
vides rapid service with quality that you can trust as we offer three state-of-the-art calibration lab and repair facilities that can calibrate up to
20,000 lbf.ft.
With over 45 years of experience, Mountz’s in-depth knowledge of torque is reflected in our tool’s craftsmanship and our ability to provide
solutions to both common and uncommon torque applications. We perform calibra-
tions in accordance with ANSI/NCSL-Z540. Mountz is dedicated solely to the manu-
facturing, marketing and servicing of high quality torque tools.
Mountz is an ISO 9001 certified and ISO 17025 accredited company.
Tool Service & Repair Capability
- Torque Wrench Calibration: Click Wrench, Dial Torque Wrench, Beam
Wrench, Cam-Over & Break-Over Wrench
- Torque Screwdrivers: Dial, Micrometer, Preset & Adjustable
- Torque Analyzers/Sensors: All brands
- Electric Screwdrivers: All brands
- Air Tools: All brands
Impact Wrenches, Drills, Pulse Tools, Grinders, Percussive Tools,
Air Screwdrivers, Nutrunners, DC Controlled Nutrunners
- Torque Multipliers: All brands
BLG-Series Operating Instructions
Mountz Service Locations
Eastern Service Center
19051 Underwood Rd.
Foley, AL 36535
Phone: [phone]
Fax: [phone]
Western Service Center
1080 N.11th Street
San Jose, CA 95112
Phone: [phone]
Fax: [phone]
www.mountztorque.com
[email protected]
Download a “Service Form” and include a copy
when you send the tools in to be serviced.
Looking for fasteners?
www.mrmetric.com
Page 5