Moxa Technologies DA-820 Series User manual

– 1 – – 2 – – 3 –
P/N: 1802008200010
DA-820 Series
Rackmount Computer
Quick Installation Guide
First Edition, October 2014
Overview
The DA-820’s main operating system is based on the lntel Core i7
CPU and QM77 chipset, which supports standard x86 platform. The
DA-820 has 2 VGA connections, 6 USB ports, 4 Gigabit LAN ports,
and 2 RS/232/422/485 3-in-1 serial ports, and is equipped with a
4 SATA disk interface and default support for RAID 0/1/5/10. In
addition, the DA-820 is specifically designed for substation
applications that require precise time synchronization and
products meeting the IEC 61850-3 standard. The flexible design
makes the DA-820 suitable for local SCADA, environmental
monitoring, video surveillance, protocol conversion, and PRP/HSR
redundancy applications, and the cybersecurity functionality
allows you to maintain secure network communications.
Package Checklist
Each basic system model is shipped with following standard items:
•DA-820 rackmount computer
•Rackmount kit
•Quick Installation Guide
•Documentation and software CD
•Warranty card
Hardware Installation
Front View
Rear View
*The power input supports two types of power supply:
HV: 100 to 240 VAC/VDC
LV: 24 to 110 VDC
Connecting the Power
Use a screwdriver to loosen the terminal connector’s clamp screws.
Connect the power cord wires to the screws, and then retighten the
screws. The Power LED will light up to indicate that power is being
supplied to the DA-820, after which the BIOS will initialize the flash
disk module, causing the Storage LED to blink. It should take
about 30 to 60 seconds for the operating system to complete the
boot process.
Alternating Current (AC),
Single Power
Alternating Current (AC),
Dual Power
Direct Current (DC),
Single Power
Direct Current (DC),
Dual Power
For more detailed power connection and surge protection
information, refer to the Hardware User’s Manual.
Front Panel LEDs
There are 28 LED indicators on the front panel. The LEDs are
described in the following table.
LED
Color
Description
Power
Green
Power is on
Off No power input or power error
exists
Storage
Yellow/
Blinking
Data is being written to or to read
from the storage unit
Off
Storage unit is idle
P1
(Non-functional for
single power supply)
Off
The 1st power in on
Red Error in the 2nd power supply
P2
(Non-functional for
single power supply)
Off
The 2nd power is on
Red Error in the 1st power supply
Gigabit LAN LEDs
1-4
Green
100 Mbps Ethernet mode
Orange 1000 Mbps (Gigabit) Ethernet
mode
Serial Port 1/2
Green
Tx
Yellow
Rx
Programmable 1-8
Green/
Blinking
1-8 programming action is in
process
Connecting to a Display
The DA-820 comes with 2 VGA interfaces that use D-Sub 15-pin
female connectors.
USB Ports
The DA-820 comes with 6 USB 2.0 ports, with 4 on the rear panel
and 2 on the front panel. The USB ports can be used to connect a
keyboard, mouse, or other peripherals, such as flash drives for
expanding the system’s storage capacity.

– 4 – – 5 – – 6 –
www.moxa.com/support
The Americas:
[phone] (toll-free: 1-888-669-2872)
Europe:
[phone]
Asia-Pacific:
[phone]
China:
[phone] (toll-free: 800-820-5036)
2014 Moxa Inc. All rights reserved.
Serial Ports
The DA-820 comes with 2 software-selectable RS-232/422/485
serial ports on the rear panel. The ports use DB9 male connectors.
Refer to the following table for pin assignments.
Pin
RS-232
RS-422
RS-485
(4-wire)
RS-485
(2-wire)
1
DCD
TxDA(-)
TxDA(-)
–
2
RxD
TxDB(+)
TxDB(+)
–
3
TxD
RxDB(+)
RxDB(+)
DataB(+)
4
DTR
RxDA(-)
RxDA(-)
DataA(-)
5
GND
GND
GND
GND
6
DSR
–
–
–
7
RTS
–
–
–
8
CTS
–
–
–
Ethernet Ports
The DA-820 has 4 100/1000 Mbps RJ45 Ethernet ports. Refer to
the following table for pin assignments.
Pin
100 Mbps
1000 Mbps
1
Tx+
TRD(0)+
2
Tx-
TRD(0)-
3
Rx+
TRD(1)+
4
–
TRD(2)+
5
–
TRD(2)-
6
Rx-
TRD(1)-
7
–
TRD(3)+
8
–
TRD(3)-
The default IP addresses and netmasks of the Ethernet ports are
shown below. Note that W7E models default to DHCP.
Default IP Address
Netmask
LAN 1
192.168.3.127
255.255.255.0
LAN 2
192.168.4.127
255.255.255.0
LAN 3
192.168.5.127
255.255.255.0
LAN 4
192.168.6.127
255.255.255.0
Installing Removable Storage
The DA-820 has 4 hot-swappable 2.5” SSD/HDD storage trays
located on the front panel for installing additional storage drives.
Remove the screws on the trays to install the SSD/HDD storage
drives. RAID 0, 1, 5, and 10 are supported.
Configuring the Ethernet Interface
Linux users should follow these steps:
If you use the console cable to configure network settings for the
first time, use the following commands to edit the interfaces file.
First, make sure all network interfaces are offline before you
reconfigure the LAN settings:
MOXA:~# ifdown –a
Next, edit the network interfaces file; you may use a text editor of
your choice, but vi is the default editor on the DA-820-LX:
MOXA:~#vi /etc/network/interfaces
You may set the DA-820 for either dynamic IP addressing or static
IP addressing. For dynamic IP addressing, enter the following lines
into the network interfaces file:
# The primary network interface
auto eth0
iface eth0 inet dhcp
To configure an interface for static IP addressing, use the following
configuration. Each interface must be configured with separate
entries in the network/interfaces file; LAN1 corresponds to eth0,
LAN 2 corresponds to eth1, and so on for the remaining interfaces.
# The loopback network interface
auto lo
iface lo inet loopback
# The first LAN interface, LAN 1
auto eth0
iface eth0 inet static
address 192.168.3.127
netmask 255.255.255.0
broadcast 192.168.3.255
# The second LAN interface, LAN 2
auto eth1
iface eth1 inet static
address 192.168.4.127
netmask 255.255.255.0
broadcast 192.168.4.255
Exit vi by typing:
:wq
After the interfaces file has been configured, use the following
commands to reinitialize the network interfaces and activate the
new settings immediately:
MOXA:~#sync; ifup –a
Win7 users should follow these steps:
Step 1:
Go to Start Control Panel Network and Internet

Network Connections.
Step 2:
On the Local Area Connection Properties screen, click
Internet Protocol (TCP/IP) and select Properties.
Step 3:
Click OK after inputting the preferred IP address and
netmask.