Moxa Technologies V2406A Series Instructions for use

V2406A Hardware User’s Manual
Edition 3.0, February 2017
www.moxa.com/product
© 2017 Moxa Inc., All rights reserved.

V2406A Hardware User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in accordance with
the terms of that agreement.
Copyright Notice
© 2017 Moxa Inc. All rights reserved.
Trademarks
The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the part of
Moxa.
Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited
to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the
products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for
its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Americas
Toll
-free: 1-888-669-2872
Tel:
[phone]
Fax:
[phone]
Mox
a China (Shanghai office)
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe
Tel:
[phone]
Fax:
[phone]
Moxa Asia
-Pacific
Tel:
[phone]
Fax:
[phone]
Moxa India
Tel:
[phone]
Fax:
[phone]

Table of Contents
1. Introduction...................................................................................................................................... 1-1
Package Checklist...............................................................................................................................1-2
Product Features ................................................................................................................................1-2
V2406A Hardware Specifications...........................................................................................................1-2
Hardware Block Diagram .....................................................................................................................1-5
2. Hardware Introduction ..................................................................................................................... 2-1
Appearance........................................................................................................................................2-2
Dimensions (unit = mm) .....................................................................................................................2-3
LED Indicators....................................................................................................................................2-3
Reset Button......................................................................................................................................2-4
Real Time Clock (RTC).........................................................................................................................2-4
3. Hardware Connection Description..................................................................................................... 3-1
Installing theV2406A...........................................................................................................................3-2
Wiring Requirements...........................................................................................................................3-4
Connecting the Power ..................................................................................................................3-5
Grounding the Unit......................................................................................................................3-5
Connecting Data Transmission Cables ...................................................................................................3-5
Connecting to the Network ...........................................................................................................3-5
Connecting to a Serial Device .......................................................................................................3-6
Installing a CFast Card.................................................................................................................3-6
Connecting to a USB Device.................................................................................................................3-7
DI/DO ...............................................................................................................................................3-8
Connecting to a DVI-I Monitor..............................................................................................................3-9
Connecting to a Speaker or a Headphone ............................................................................................3-10
Installing a SATA Hard Disk ...............................................................................................................3-10
RTC Battery Replacement ..................................................................................................................3-10
4. BIOS Setup........................................................................................................................................ 4-1
Entering the BIOS Setup......................................................................................................................4-2
Main Information................................................................................................................................4-3
Advanced Settings..............................................................................................................................4-3
Boot Configuration ......................................................................................................................4-4
HDC Configuration.......................................................................................................................4-4
Video Configuration .....................................................................................................................4-5
Chipset Configuration ..................................................................................................................4-7
Hardware Monitor........................................................................................................................4-8
SMART RECOVERY Info ................................................................................................................4-9
Security Settings ................................................................................................................................4-9
Set Supervisor Password............................................................................................................4-10
Power Settings .................................................................................................................................4-10
Turbo Mode ..............................................................................................................................4-10
Auto Wake on S5 ......................................................................................................................4-11
Wake on LAN............................................................................................................................4-12
Boot Settings ...................................................................................................................................4-12
Boot Type.................................................................................................................................4-12
PXE Boot to LAN........................................................................................................................4-12
Add Boot Options ......................................................................................................................4-12
USB Boot .................................................................................................................................4-13
EFI Device First.........................................................................................................................4-13
Boot Delay Time........................................................................................................................4-13
Legacy.....................................................................................................................................4-13
Exit Settings ....................................................................................................................................4-14
Exit Saving Changes..................................................................................................................4-15
Save Change Without Exit ..........................................................................................................4-15
Exit Discarding Changes.............................................................................................................4-15
Load Optimal Defaults................................................................................................................4-15
Load Custom Defaults................................................................................................................4-15
Save Custom Defaults................................................................................................................4-15
Discard Changes .......................................................................................................................4-15
Upgrading the BIOS..........................................................................................................................4-16
A. Regulatory Approval Statement ........................................................................................................ A-1

1
1. Introduction
The V2406A series embedded computers are based on the Intel 3rd-generation processor and feature four
RS-232/422/485 serial ports, dual Gigabit Ethernet ports, audio in/out, three USB 2.0 hosts, two CFast sockets,
and one SATA storage socket. In addition, the V2406A computers have dual DVI-I outputs, and are compliant
with a portion of EN 50155 covering operating temperature, power input voltage, power surge, ESD, and
vibration, making them particularly well-suited for railway applications.
The dual Gigabit Ethernet ports with M12 X-coded connectors offer a reliable solution for network redundancy,
promising continuous operation for data communication and management. As an added convenience, the
V2406A computers have six DIs and two DOs for connecting digital input/output devices, and the CFast feature
provides the reliability needed for industrial applications that require data buffering and storage expansion.
Pre-installed with Windows Embedded Standard 7 or Debian 7 (available for custom orders only), the V2406A
computers provide programmers with a friendly environment for developing sophisticated, error-free
application software at a low cost. Wide temperature models of the V2406A that operate reliably in a -40 to
70°C operating temperature range are also available, offering an optimal solution for applications subjected to
harsh environments.
The following topics are covered in this chapter:

Package Checklist

Product Features

V2406A Hardware Specifications

Hardware Block Diagram

V2406A Hardware Introduction
1-2
Package Checklist
Each model is shipped with the following items:
•V2406A series embedded computer
•Wall mounting kit
•Documentation and software CD or DVD
•Quick installation guide (printed)
•Warranty card
NOTE: Please notify your sales representative if any of the above items are missing or damaged.
Product Features
V2406A embedded computers include the following features:
•Intel Celeron/Core i7 processor for high performance
•Up to 8 GB DDR3 1600 SO-DIMM RAM
•Dual independent displays
•2 Gigabit Ethernet ports with M12 X-coded connectors
•1 SATA connector and 2 CFast sockets for storage expansion
•M12 A-coded power connector
•EN 50121-4 compliancy
•Complies with a portion of EN 50155 specifications
•Ready-to-run Embedded Linux, or Windows Embedded Standard 7 platform
•-40 to 70°C wide temperature models available
•Supports SNMP-based system configuration, control, and monitoring
V2406A Hardware Specifications
Computer
CPU:
• Intel Celeron 1047UE processor (2M cache, 1.40 GHz) for the V2406A
-C2 series
• Intel Core i7
-3517UE processor (6M cache, 1.7 GHz) for the V2406A-C7 series
OS:
Windows Embedded Standard 7 or Linux Debian 7
System Chipset:
Mobile Intel® HM65 Express
System Memory:
1 DDR3-1600 SO-DIMM SDRAM slot, 8 GB max., 4 GB pre-installed
USB:
3 bootable USB 2.0 ports (2 type A, 1 M12 D-coded)
Storage
HDD/SSD Support:
1 internal SATA-II bus for 2.5” HDD/SSD*
*Storage drive not included. To be purchased separately.
CFast Support:
1 slot for OS*, 1 slot for backup storage
*32
-bit W7E requires at least an 8 GB CFast card
*64
-bit W7E requires at least a 16 GB CFast card (optional)
*Linux Debian 7 requires at least an 8 GB CFast card (to be purchased separately)
Other Peripherals
Audio:
Line-in, line-out interface (M12 A-coded)
Display
Graphics Controller:
Intel® HD Graphics 4000 (integrated)
Connector Type:
2 DVI-I connectors
Display Interface:
DVI up to 1920x1200 resolution @ 60 Hz
VGA up to 1920x1200 resolution @ 60 Hz
VGA up to 2048x1536 resolution @ 75 Hz

V2406A Hardware Introduction
1-3
Ethernet Interface
LAN:
2 auto-sensing 10/100/1000 Mbps ports (M12 X-coded)
Isolation Protection:
1.5 kV
Serial Interface
Serial Standards:
4 RS-232/422/485 ports, software selectable (DB9 male)
ESD Protection:
4 kV for all signals
Isolation Protection:
1.5 kV
Serial Communication Parameters
Data Bits:
5, 6, 7, 8
Stop Bits:
1, 1.5, 2
Parity:
None, Even, Odd, Space, Mark
Flow Control:
RTS/CTS, XON/XOFF, ADDC® (automatic data direction control) for RS-485
Baudrate:
50 bps to 921.6 kbps (non-standard baudrates supported; see user’s manual for details)
Serial Signals
RS
-232: TxD, RxD, DTR, DSR, RTS, CTS, DCD, GND
RS
-422: TxD+, TxD-, RxD+, RxD-, GND
RS
-485-4w: TxD+, TxD-, RxD+, RxD-, GND
RS
-485-2w: Data+, Data-, GND
Digital Input
Input Channels:
6, source type
Input Voltage:
0 to 30 VDC at 25 Hz
Digital Input Levels for Dry Contacts:
• Logic level 0: Close to GND
• Logic level 1: Open
Digital Input Levels for Wet Contacts:
• Logic level 0: +3
V max.
• Logic level 1: +10 V to +30 V (Source to DI)
Isolation:
3 kV optical isolation
Digital Output
Output Channels:
2, sink type
Output Current:
Max. 200 mA per channel
On
-state Voltage: 24 VDC nominal, open collector to 30 VDC
Connector Type:
10-pin screw-fastened Euroblock terminal (6 inputs, 2 outputs, DI Source, GND)
Isolation:
3 kV optical isolation
LEDs
System:
Power, Storage
LAN:
2 per port (10/100/1000 Mbps)
Serial:
2 per port (Tx and Rx)
Switches and Buttons
Power Switch:
on/off (front panel)
Reset Button:
For warm reboot (front panel)
Physical Characteristics
Housing:
Aluminum
Weight:
2 kg
Dimensions:
Without ears: 250 x 57 x 154 mm (9.84 x 2.23 x 6.06 in)
With ears: 275 x 63 x 154 mm (10.83 x 2.47 x 6.06 in)
Mounting:
DIN rail, wall, VESA
Environmental Limits
Operating Temperature*:
Standard models:
-25 to 55°C (-13 to 131°F)
Wide temp. models:
-40 to 70°C (-40 to 158°F)
Storage Temperature*:
-40 to 85°C (-40 to 185°F)

V2406A Hardware Introduction
1-4
*without HDD installed
Ambient
Relative Humidity: 5 to 95% (non-condensing)
Anti
-Vibration: EN 50155 standard
Anti
-Shock: EN 50155 standard
Conformal Coating:
Available on request
Power Requirements
Input Voltage:
12 to 48 VDC (M12 A-coded)
Note: Compliant with EN 50155 at 24
VDC
Power Consumption:
• 3.24 A @ 12 VDC, 38.88 W
• 0.74 A @ 48 VDC, 35.52 W
Standards and Certifications
Safety:
UL 60950-1, CSA C22.2 No. 60950-1-07, EN 60950-1
EMC:
EN 55032 Class A, EN 61000-3-2 Class D, EN 61000-3-3, EN 55024, FCC Part 15 Subpart B Class A
Green Product:
RoHS, CRoHS, WEEE
Rail Traffic:
EN 50155*, EN 50121-4, IEC 61373
*Complies with a portion of EN 50155 specifications. Please cont
act Moxa or a Moxa distributor for details.
Reliability
Automatic Reboot Trigger:
Software-programmable watchdog timer configurable from 1 to 255 seconds
Warranty
Warranty Period:
3 years
Details:
See www.moxa.com/warranty
Note: These hardware
specifications describe the embedded computer unit itself, but not its official
accessories. In particular, the wide temperature specification does not apply to accessories such as power
adapters and cables.

V2406A Hardware Introduction
1-5
Hardware Block Diagram

2
2. Hardware Introduction
The V2406A series embedded computers are compact, well-designed, and rugged enough for industrial
applications. LED indicators help you monitor performance and identify trouble spots, multiple serial ports
allow you to connect different devices for wireless operation, and the reliable and stable hardware platform lets
you devote your attention to developing your applications.
The following topics are covered in this chapter:

Appearance

Dimensions (unit = mm)

LED Indicators

Reset Button

Real Time Clock (RTC)

V2406A Hardware Hardware Introduction
2-2
Appearance
Front View
Rear View

V2406A Hardware Hardware Introduction
2-3
Dimensions (unit = mm)
LED Indicators
LED Name LED Color LED Function
Power Green Power is on and functioning normally.
Off Power is off or power error exists.
Storage Yellow CFast card/HDD/SSD is transmitting data.
Off CFast card/HDD/SSD is not transmitting data.
LAN (1 or 2) Green 100 Mbps Ethernet mode.
Yellow 1000 Mbps Ethernet mode.
Off 10 Mbps or no activity.
TX (P1-P4) Green Serial port (P1-P4) is transmitting data.
Off Serial port (P1-P4) is not transmitting data.
RX (P1-P4) Yellow Serial port (P1-P4) is receiving data.
Off Serial port (P1-P4) is not receiving data.

V2406A Hardware Hardware Introduction
2-4
Reset Button
Press the Reset Button on the rear panel of the V2406A to reboot the system automatically. The Ready LED
will blink on and off for the first 5 seconds, and then maintain a steady glow once the system has rebooted.
The V2406A does not support a “Reset to Default” function.
Real Time Clock (RTC)
The V2406A’s real-time clock is powered by a lithium battery. You can easily replace the battery yourself using
an optional battery kit*. However, please note that there is a risk of explosion if the battery is replaced by an
incorrect type of battery. Refer to the V2406A Hardware User's Manual or contact a qualified Moxa support
engineer if you have any questions about the RTC battery.
*Moxa offers an “RTC battery kit” that you can use to easily replace the battery. For details, check the optional
accessories section of the V2406A datasheet.
ATTENTION
There is a risk of explosion if the battery is replaced by a battery of the incorrect type.

3
3. Hardware Connection Description
In this chapter, we show how to connect the embedded computers to the network and to various devices.
The following topics are covered in this chapter:

Installing theV2406A

Wiring Requirements
Connecting the Power
Grounding the Unit

Connecting Data Transmission Cables
Connecting to the Network
Connecting to a Serial Device
Installing a CFast Card

Connecting to a USB Device

DI/DO

Connecting to a DVI-I Monitor

Connecting to a Speaker or a Headphone

Installing a SATA Hard Disk

RTC Battery Replacement

V2406A Hardware Hardware Connection Description
3-2
Installing theV2406A
Wall or Cabinet Mounting
The V2406A comes with two metal brackets for attaching the device on a wall or to the inside of a cabinet.
Complete the following steps to attach the mounting brackets to the V2406A.
Step 1: Use two screws for each bracket to attach the brackets to the rear of the V2406A.
Step 2: Use two screws per side to mount the V2406A on a wall or in a cabinet.
Din-Rail Mounting
The V2406A can be installed on a DIN-rail with the optional DIN-rail kit. This DIN-rail kit must be purchased
separately. The DIN-rail kit includes two DIN-rail brackets and eight screws.

V2406A Hardware Hardware Connection Description
3-3
To attach the DIN-rail kit, complete the following steps:
1. Turn the V2406A over so the bottom is facing up.
2. Locate the screw holes on the bottom of the V2406A.
3. Place the brackets on the bottom of the V2406A and align the screw holes on the brackets with the screw
holes on the V2406A.
4. Insert and tighten the screws into the screw holes.
NOTE
Use all eight screws to ensure that the V2406A is safely and securely installed on the DIN
rail.
5. When the brackets are firmly attached with the screws, you can install the V2406A onto a DIN-rail.
To remove the V2406A from the DIN rail, first use a screwdriver to pull down the DIN-rail connector to unlock
it. The following figure shows a locked DIN-rail connector and an unlocked DIN-rail connector.
WARNING
Two people are required to remove
the V2406A from a DIN rail.
When the DIN
-rail connectors are unlocked, the V2406A is detached from the DIN rail automatically.

V2406A Hardware Hardware Connection Description
3-4
To re-install the V2406A on the DIN rail, use a screwdriver to press the buckle so that it can be released. At this
point, it can be re-installed on the DIN rail.
Wiring Requirements
In this section, we describe how to connect serial devices to the V2406A embedded computer.
Be sure to read and follow these common safety precautions before proceeding with the installation of any
electronic device:
•Use separate paths to route wiring for power and devices. If power wiring and device wiring paths must
cross, make sure the wires are perpendicular at the intersection point.
NOTE: Do not run signal or communication wiring together with power wiring in the same wire conduit. To
avoid interference, wires with different signal characteristics should be routed separately.
•Use the type of signal transmitted through a wire to determine which wires should be kept separate. The
rule of thumb is that wiring that shares similar electrical characteristics can be bundled together.
•Keep input wiring and output wiring separate.
•It is advisable to label the wiring to all devices in the system.

V2406A Hardware Hardware Connection Description
3-5
ATTENTION
Safety First!
Be sure to disconnect the power cord before installing and/or wiring your
V2406A.
Wiring Caution!
Calculate
the maximum possible current in each power wire and common wire. Observe all electrical codes
dictating the maximum current allowable for each wire size.
If the current goes above the maximum ratings,
the wiring could overheat, causing serious damage to
your equipment.
Temperature Caution!
Be careful when handling the unit. When the unit is plugged in, the internal components generate heat, and
consequently the outer casing may feel hot to the touch.
Connecting the Power
Connect the 12 to 48 VDC power line with M12 A-coded connector to the V2406A computer. If the power is
supplied properly, the “Ready” LED will glow a solid green after a 25- to 30-second delay.
Grounding the Unit
Grounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI). Run the
ground connection from the ground screw to the grounding surface prior to connecting the power.
ATTENTION
This product is intended to be mounted o
n a well-grounded mounting surface, such as a metal panel.
SG: The Shielded Ground (sometimes called Protected Ground) contact is the
central pin of the power input connector
.
Connect the SG wire to an appropriate
grounded metal surface.
Connecting Data Transmission Cables
In this section, we describe how to connect the V2406A embedded computer to a network and serial devices.
Connecting to the Network
Connect your network cable to the embedded computer’s Ethernet port. The other end of the cable should be
connected to your Ethernet network. When the cable is properly connected, the LEDs on the embedded
computer’s Ethernet port turns on to indicate a valid connection.
Two 10/100/1000 Mbps Ethernet ports using M12 X-coded connectors are located on the rear panel of the
embedded computer. See the following figure for the location of the Ethernet ports and the pin assignments.
NOTE
Th
e pin assignments for the V2406A computer’s Ethernet port are shown in the following figure. If you
create
your own Ethernet cable,
make sure that you match the pin assignments on the connector of the Ethernet
cable.

V2406A Hardware Hardware Connection Description
3-6
Connecting to a Serial Device
Use a serial cable to
connect
your serial device
to the embedded computer’s serial port. Serial
ports P1 to P4 have male DB9 connectors and
can be configured for RS
-232, RS-422, or
RS
-485 communication
(refer to the software
manual for your operating system version)
.
The pin
assignments are shown in the
following table:
DB9 Male Port
RS
-232/422/485 Pinouts
Pin RS-232 RS-422 RS-485
(4-wire)
RS-485
(2-wire)
1 DCD TxDA(-) TxDA(-) –
2 RxD TxDB(+) TxDB(+) –
3 TxD RxDB(+) RxDB(+) DataB(+)
4 DTR RxDA(-) RxDA(-) DataA(-)
5 GND GND GND GND
6 DSR – – –
7 RTS – – –
8 CTS – – –
Installing a CFast Card
The V2406A embedded computers come with a CFast socket. To insert a CFast card, follow these instructions:
1. Disconnect the V2406A from its power source.
2. The CFast slot is located on the left side of the front panel. Loosen the screws on the CFast socket cover.
3. Press the CFast card to eject it.
When you want to insert it back into the CFast slot, slide it into the slot and then push it in with your finger
until it latches firmly.
NOTE
Make sure
that you properly orient the the CFast card when installing it; otherwise, you may not be able to
insert the card all the way into the slot.

V2406A Hardware Hardware Connection Description
3-7
ATTENTION
Make sure that you
orient the CFast card properly before pushing it into the slot. The bottom of the CFast
card
must be facing
up for the card to work properly, and for the CFast socket cover to be installed properly.
4. After the CFast card is installed correctly, fasten the screws on the CFast card socket cover to install it.
ATTENTION
The V2406A embedded computer does not support the CFas
t hot swap and PnP (Plug and Play) functions.
You
must disconnect the
power source first, before inserting or removing the CFast card.
Connecting to a USB Device
The V2406A comes with one USB 2.0 host with M12 D-coded connector on the front panel and two USB 2.0
hosts with type A connectors on the rear panel. These ports can be used for connecting to an external flash disk
or hard drive for storing data. You can also use these USB ports to connect to a keyboard or a mouse.
The following figures show the locations of the USB ports and the M12 D-coded connector pin assignment.