Moxa Technologies MGate 5135 Series User manual

P/N: 1802051350010
*1802051350010*
MGate 5135/5435 Series
Quick Installation Guide
Version 1.0, September 2022
Technical Support Contact Information
www.moxa.com/support

2022 Moxa Inc. All rights reserved.

- 2 -
Overview
The MGate 5135/5435 is an industrial Ethernet gateway for Modbus
RTU/ASCII/TCP and EtherNet/IP network communications.
Package Checklist
Before installing the MGate 5135/5435, verify that the package
contains the following items:
•1 MGate 5135 or MGate 5435 gateway
•Quick installation guide (printed)
•Warranty card
NOTE
Please notify your sales representative if any of the above
items are missing or damaged.
Optional Accessories (can be purchased separately)
•Mini DB9F-to-TB: DB9 female to terminal block connector
•WK-25: Wall-mounting kit, 2 plates, 4 screws, 25 x 43 x 2 mm
Hardware Introduction
LED Indicators
LED
Color
Description
PWR 1, PWR 2
Green
Power is on.
Off
Power is off.
Ready
Off
Power is off.
Green
Steady: Power is on, and the MGate is
functioning normally.
Blinking (1 sec.): The MGate has been located
by the MGate Manager’s Location function.
Red
Steady: Power is on, and the MGate is booting
up.
Blinking (0.5 sec.): Indicates an IP conflict, or
the DHCP or BOOTP server is not responding
properly.
Blinking (0.1 sec.): the microSD card failed.
EtherNet/IP
Adapter
Off
No connection has been established.
Green Steady: I/O data is being exchanged with all
of the connections.
Red
Steady: Rejects the connection due to
incorrect configurations.
Blinking (1 sec.): One or more connections
timed out.
Modbus
RTU/ASCII/TCP
Client
Off
No communication with Modbus device.
Green
Modbus communication in progress.
Red
Blinking (1 sec.):Communication error.
1. The Modbus
slave device returned an error
(exception).
2. Received a frame error (parity error,
checksum error).
3. Timeout (the slave device does not
respond).

- 3 -
LED
Color
Description
4. TCP connection failed (only for Modbus
TCP).
ETH 1, ETH 2
Green
Steady ON: Ethernet link on at 100Mbps.
Blinking: Data transmitting at 100Mbps.
Amber
Steady ON: Ethernet link on at 10Mbps.
Blinking: Data transmitting at 10Mbps.
Off
Ethernet is not connected.
Dimensions
MGate 5135
MGate 5435
Reset Button
Restore the MGate to factory default settings by using a pointed object
(such as a straightened paper clip) to hold the reset button down until
the Ready LED stops blinking (approx. five seconds).

- 4 -
Hardware Installation Procedure
1. Connect the power adapter. Connect the 12 to 48 VDC power line
or DIN-rail power supply to the terminal block of the MGate
5135/5435 device.
2. Use a Modbus serial cable to connect the MGate to a Modbus slave
device.
3. Use an Ethernet cable to connect the MGate to the EtherNet/IP
controller.
4. We designed the MGate 5135/5435 to attach to a DIN rail or
mounted on a wall. For DIN-rail mounting, push down the spring
and properly attach it to the DIN rail until it “snaps” into place. For
wall mounting, install the wall-mount kit (optional) first and then
screw the device onto the wall.
The following figure illustrates the two mounting options:
Wall- or Cabinet-mounting
We provide two metal plates for mounting the unit
on a wall or inside a cabinet. Attach the
plates to
the unit’s rear panel with screws. With the plates
attached, use screws to mount the unit on a wall.
The heads of the screws should be 5 to 7 mm in
diameter, the shafts should be 3 to 4 mm in
diameter, and the length of the screws should be
over 10.5 mm.
Software Installation Information
Please download the User Manual and Device Search Utility (DSU) from
Moxa’s website: www.moxa.com
Refer to the User’s Manual for additional details on using the DSU. The
MGate 5135/5435 also supports login via a web browser.
Default IP address: 192.168.127.254
Create your administration account and password when you log in the
first time.

- 5 -
Pin Assignments
Modbus Serial Port (Male DB9)
Pin RS-232
RS-422/
RS-485 (4W)
RS-485 (2W)
1
DCD
TxD-(A)
–
2
RXD
TxD+(B)
–
3
TXD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5*
GND
GND
GND
6
DSR
–
–
7
RTS
–
–
8
CTS
–
–
9
–
–
–
*Signal ground
Ethernet Port (RJ45)
Pin
Signal
1
Tx+
2
Tx-
3
Rx+
6
Rx-
Power Input and Relay Output Pinouts
V2+ V2-
V1+ V1-
DC
Power
Input 2
DC
Power
Input 2
N.O. Common N.C.
DC
Power
Input 1
DC
Power
Input 1
Specifications
Power Parameters
Power Input
12 to 48 VDC
Power Consumption
MGate 5135 Series: 455 mA max.
MGate 5435 Series: 455 mA max.
Relays
Contact Current Rating
Resistive load: 2 A @ 30 VDC
Environmental Limits
Operating
Temperature
Standard models: -10 to 60°C (14 to 140°F)
Wide temp. models: -40 to 75°C (-40 to 167°F)
Storage Temperature
(package included)
-40 to 85°C (-40 to 185°F)
Ambient Relative
Humidity
5 to 95% RH
Physical Characteristics
Dimensions
MGate 5135 Series:
25 x 90 x 129.6 mm (0.98 x 3.54 x 5.1 in)
MGate 5435 Series:
42 x 90 x 129.6 mm (1.65 x 3.54 x 5.1 in)

- 6 -
Weight
MGate 5135 Series: 294 g (0.65 lb)
MGate 5435 Series: 403 g (0.89 lb)
Reliability
Alert Tools
Built-in buzzer and RTC
MTBF MGate 5135 Series: 1,240,821 hrs.
MGate 5435 Series: 689,989 hrs.
ATTENTION
Power
terminal plug wiring size is 28-14 AWG, tighten to 1.7
in-lbs, wire Min. 80°C, Use copper conductors only.
Hot Surface Label.
Functional earth terminal.
ATTENTION
•
This device is an open-type equipment and intended to be
installed in a suitable enclosure.
•
If the equipment is used in a manner not specified by the
manufacturer, the protection provided by the equipment
may be impaired.
•
When installing, the assembler is responsible for the safety
of the system in which the equipment is incorporated.
NOTE
•This device is intended for use indoors and at altitudes up
to 2,000 meters.
•Pollution degree 2.
NOTE
Clean the device with a soft cloth, dry or with water.
NOTE
The power input specification complies with the requirements of
SELV (Safety Extra Low Voltage), and the power supply should
comply with UL 61010-1 and UL 61010-2-201.
For any repair or maintenance needs, please contact us.
Moxa Inc.
No. 1111, Heping Rd., Bade Dist., Taoyuan City 334004, Taiwan
[phone]