Moxa Technologies MGate 5119 Series User manual

P/N: 1802051190010
*1802051190010*
MGate 5119 Series
Quick Installation Guide
Version 1.0, December 2021
Technical Support Contact Information
www.moxa.com/support

2021 Moxa Inc. All rights reserved.

- 2 -
Overview
The MGate 5119 Series is an Ethernet gateway designed for the power
industry to integrate Modbus, DNP3, IEC 60870-5-101/104 devices to
an IEC 61850 MMS network.
Package Checklist
Before installing the MGate 5119, verify that the package contains the
following items:
•1 MGate 5119 gateway
•1 serial cable: CBL-RJ45F9-150
•Quick installation guide (printed)
•Warranty card
Please notify your sales representative if any of the above items is
missing or damaged.
Optional Accessories (can be purchased separately)
•CBL-F9M9-150: DB9-female-to-DB9-male serial cable, 150 cm
•CBL-F9M9-20: DB9-female-to-DB9-male serial cable, 20 cm
•CBL-RJ45F9-150: RJ45-to-DB9-female serial cable, 150 cm
•CBL-RJ45SF9-150: RJ45-to-DB9-female serial shielded cable, 150
cm
•Mini DB9F-to-TB DB9: Female-to-terminal-block connector
•WK-36-02: Wall-mounting kit, 2 plates with 6 screws
•CBL-PJTB-10: Non-locking barrel plug to bare-wire cable
Hardware Introduction
LED Indicators
LED
Color
Description
Ready
Off
Power is off or a fault condition exists
Green Steady: Power is on, and the MGate is functioning
normally
Red
Steady: Power is on, and the MGate is booting up
Blinking slowly: Indicates an IP conflict, or the
DHCP or BOOTP server is not responding properly
Flashing quickly: the microSD card failed
MB/101/
104/DNP3
Off
No communication with a Modbus/101/104/DNP3
device
Green Normal Modbus/101/104/DNP3 communication in
progress
Red
When the MGate 5119 acts as a Modbus master:
1. Received an exception code from the slave
device
2. Received a framing error (parity error,
checksum error)
3. Timeout (the master sent a request but no
response was received)
When the MGate 5119 acts as an IEC 60870-5-
101/104/ DNP3 master:

- 3 -
LED
Color
Description
1. Received an outstation exception (format
error, checksum error, invalid data, outstation
responds are not supported)
2. Timeout (the master sent a command, but no
response was received)
850
Off
No communication with the IEC 61850 system
Green
Normal IEC 61850 communication in progress
Red
When the MGate 5119 acts as an IEC 61850
server:
1. Received an abnormal package (wrong
format, unsupported function code)
2. Failed to establish an IEC 61850 connection
3. Disconnected the IEC 61850 connection
Dimensions
Unit: mm (inch)
Reset Button
Restore the MGate to factory default settings by using a pointed object
(such as a straightened paper clip) to hold the reset button down until
the Ready LED stops blinking (approximately five seconds).
Pull-high, Pull-low, and Terminator for RS-485
Beneath the MGate 5119’s top cover, you will find DIP switches to
adjust each serial port’s pull-high resistor, pull-low resistor, and
terminator.
SW
1
2
3
Pull-high
resistor
Pull-low
resistor
Terminator
ON
1 kΩ
1 kΩ
120 Ω
OFF
150 kΩ*
150 kΩ*
–*
*Default

- 4 -
Hardware Installation Procedure
1. Connect the MGate 5119's terminal block to the power supply,
which could provide 12 to 48 VDC.
2. Use a serial or Ethernet cable to connect the MGate to the Modbus
RTU/ASCII/TCP, DNP3 Serial/TCP, IEC60870-5-101/104 device.
3. Use an Ethernet cable to connect the MGate to the IEC 61850 MMS
system.
4. The MGate 5119 is designed to be attached to a DIN rail or
mounted on a wall. For DIN-rail mounting, push down the spring
and properly attach it to the DIN rail until it “snaps” into place. For
wall mounting, install the wall-mount kit (optional) first and then
screw the device onto the wall. An M3 screw is suggested, and the
minimum length of the screw should be 10 mm.
The following figure illustrates the two suggested mounting options:
The following figure illustrates how to attach screws to the mounting
kits:
DIN Rail:

- 5 -
Wall-mount:
NOTE
The equipment is intended to be supplied by the external power
source (UL listed/ IEC
60950-1/ IEC 62368-1), which output
complies
with ES1/SELV, PS2/LPS, output rating is 12 to 48
VDC, 0.455 A min., an ambient temperature 75°C minimum.
NOTE
Before connecting the Equipment to DC power inputs, make
sure DC power source voltage is
stable
•
The wiring of input terminal block shall be installed by
skilled person.
•
Wire type: Cu
•
Only use 28-18 AWG wire size, torque value 0.5 N-m.
•One individual conductor in a clamping point.
NOTE
If you are using a Class I adapter, the power cord should be
connected to an outlet with an earthing connection
Software Installation Information
You can download the User's Manual and Device Search Utility (DSU)
from Moxa's website: www.moxa.com. Please refer to the User’s
Manual for additional details on using the DSU.
The MGate 5119 also supports login via a web browser.
Default IP address: 192.168.127.254
Default account: admin
Default password: moxa

- 6 -
Pin Assignments
Serial Port (Male DB9)
Pin RS-232
RS-422/
RS-485 (4W)
RS-485 (2W)
1
DCD
TxD-(A)
–
2
RXD
TxD+(B)
–
3
TXD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5*
GND
GND
GND
6
DSR
–
–
7
RTS
–
–
8
CTS
–
–
9
–
–
–
*Signal ground
Ethernet Port (RJ45)
Pin
Signal
1
Tx+
2
Tx-
3
Rx+
6
Rx-
Power Input and Relay Output Pinouts
V2+ V2- V1+ V1-
Shielded
Ground
DC
Power
Input 2
DC
Power
Input 2
N.O. Common N.C.
DC
Power
Input 1
DC
Power
Input 1
Specifications
Power Requirements
Power Input
12 to 48 VDC
Input Current
455 mA max.
Operating Temperature
-40 to 75°C (-40 to 167°F)
Ambient Relative Humidity
5 to 95% (non-condensing)
Dimensions
36 x 120 x 150 mm (1.42 x 4.72 x 5.91 in)
Reliability
Alert Tools
Built-in buzzer and RTC
MTBF
1,180,203 hrs.
Moxa Inc.
No. 1111, Heping Rd., Bade Dist., Taoyuan City 334004, Taiwan