Moxa Technologies MGate EIP3170 User manual

P/N: 1802031701014
*1802031701014*
MGate EIP3170/EIP3270
Quick Installation Guide
Version 5.0, November 2019
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll
-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax:
1-714-528-6778
Moxa China (Shanghai office):
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe:
Tel:
[phone]
Fax:
[phone]
Moxa Asia-Pacific:
Tel:
[phone]
Fax:
[phone]
Moxa India:
Tel:
[phone]
Fax:
[phone]
2019 Moxa Inc. All rights reserved.

- 2 -
Overview
The MGate EIP3170 and EIP3270 are 1- and 2-port DF1-to-EtherNet/IP
gateways that provide protocol conversions for users who need to
connect Rockwell Automation PLCs to an EtherNet/IP network. The
MGate EIP3000 Series products support up to 8 EtherNet/IP clients and
8 EtherNet/IP servers simultaneously. Each client can send up to 16
requests at one time.
Package Checklist
Before installing the MGate EIP3170 or EIP3270, verify that the
package contains the following items:
•MGate EIP3170 or EIP3270 DF1 to EtherNet/IP gateway
•Quick installation guide (printed)
•Warranty card
Optional Accessories:
•DK-35A: DIN-rail mounting kit (35 mm)
•Mini DB9F-to-TB Adaptor: DB9 female to terminal block adapter
•DR-4524: 45W/2A DIN-rail 24 VDC power supply with universal 85
to 264 VAC input
•DR-75-24: 75W/3.2A DIN-rail 24 VDC power supply with universal
85 to 264 VAC input
•DR-120-24: 120W/5A DIN-rail 24 VDC power supply with 88 to
132 VAC/176 to 264 VAC input by switch
Please notify your sales representative if any of the above items is
missing or damaged.
Hardware Introduction
LED Indicators
Name
Color
Function
PWR1
Red
Power is being supplied to the power input
PWR2
Red
Power is being supplied to the power input
RDY
Red
Steady: Power is on and the unit is booting up
Blinking: IP conflict, DHCP or BOOTP server did
not respond properly, or a relay output
occurred
Green
Steady: Power is on and the unit is functioning
normally
Blinking: Unit is responding to Locate function
Off
Power is off or power error condition exists
Ethernet
Orange
10 Mbps Ethernet connection
Green
100 Mbps Ethernet connection
Off
Ethernet cable is disconnected or has a short
P1
Orange
Serial port is receiving data
Green
Serial port is transmitting data
Off
Serial port is not transmitting or receiving data
P2
(EIP3270
only)
Orange
Serial port is receiving data
Green
Serial port is transmitting data
Off
Serial port is not transmitting or receiving data

- 3 -
Reset Button
The reset button is used to load factory defaults. Use a pointed object
such as a straightened paper clip to hold the reset button down for five
seconds. Release the reset button when the Ready LED stops blinking.
Panel Layouts
The MGate EIP3170 has a male DB9 port and a terminal block for
connecting to serial devices. The MGate EIP3270 has two DB9
connectors for connecting to serial devices.

- 4 -
Hardware Installation Procedure
STEP 1:
Use a standard straight
-through Ethernet cable to connect
the unit to a network hub or switch.
STEP 2:
Connect your device to the unit’s serial port.
STEP 3:
Mount the unit on a DIN-rail.
STEP 4:
Connect the power source to power input.
Wall or Cabinet Mounting
Mounting the MGate EIP3170/3270 on to a wall
requires two screws. The heads of the screws
should be 5 to 7 mm in diameter, the shafts
should be 3 to 4 mm in diameter, and the length
of the screws should be more than 10.5
mm.
NOTE
Wall mounting is certified for use in maritime applications.
Wallmount
DIN Rail
Software Installation Information
You can download the MGate Manager, User's Manual, and Device
Search Utility (DSU) from Moxa's website: www.moxa.com. Please refer
to the User’s Manual for additional details on using the MGate Manager
and DSU.
Default IP address: 192.168.127.254
Pin Assignments
Ethernet Port (RJ45)
Pin
Signal
1
Tx+
2
Tx-
3
Rx+
6
Rx-

- 5 -
Serial Port (Male DB9)
Pin
RS-232
1
DCD
2
RxD
3
TxD
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
9
–
RS-422 (Terminal Block) Pinouts
Pin
RS-422
1
TxD+(B)
2
TxD-(A)
3
RxD+(B)
4
RxD-(A)
5
GND
Power Input and Relay Output Pinouts
V2+ V2- V1+ V1-
Shielded
Ground
DC Power
Input 1
DC
Power
Input 1
Relay
output
Relay
output
DC
Power
Input 2
DC
Power
Input 2
Environmental Specifications
Power Requirements
Power Input
12 to 48 VDC
Power Consumption
(Input Rating)
•EIP3170/EIP3170-T/EIP3270/EIP3270-T:
12 to 48 VDC, 435 mA (max.)
•EIP3270I: 12 to 48 VDC, 510 mA (max.)
•EIP3170I/EIP3170I-T:
12 to 48 VDC, 555 mA (max.)
Operating Temperature 0 to 60°C (32 to 140°F),
-40 to 75°C (-40 to 167°F) for –T model
Storage Temperature
-40 to 85°C (-40 to 185°F)
Operating Humidity
5 to 95% RH
Magnetic Isolation
Protection (Serial)
2 kV (for “I” models)
Dimensions
Without ears:
With ears extended:
29 x 89.2 x 118.5 mm (1.14 x 3.51 x 4.67
in)
29 x 89.2 x 124.5 mm (1.14 x 3.51 x 4.90
in)
Relay Output 1 digital relay output to alarm (normal
close): current-carrying capacity 1 A @ 30
VDC
Hazardous Location
UL/cUL Class 1 Division 2 Group A/B/C/D,
ATEX Zone 2, IECEx

- 6 -
This device complies with Part 15 of the FCC rules.
Operation is subject to the following conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
ATEX and IECEx Information
EIP3170/ EIP3270 Serial
1. Certificate number: DEMKO 18 ATEX 2168X
2. IECEx number: IECEx UL 18.0149X
3. Certification string: Ex nA IIC T4 Gc
Ambient Range : 0°C ≤Tamb ≤60°C (For suffix without -T)
Ambient Range : -40°C ≤Tamb ≤75°C (For suffix with -T)
4. Standards covered:
ATEX: EN 60079-0:2012+A11:2013, EN 60079-15:2010
IECEx: IEC 60079-0 Ed.6; IEC 60079-15 Ed.4
5. The conditions of safe usage:
•The equipment shall only be used in an area of at least
pollution degree 2, as defined in IEC/EN 60664-1.
•The equipment shall be installed in an enclosure that provides
a minimum ingress protection of IP4 in accordance with
IEC/EN 60079-0.
•Conductors suitable for Rated Cable Temperature ≥ 100°C
•Input conductor with 28-12 AWG (max. 3.3 mm2) to be used
with the devices
EIP3170I/ EIP3270I Serial
1. ATEX Certificate number: DEMKO 19 ATEX 2232X
2. IECEx number: IECEx UL 19.0058X
3. Certification string: Ex nA IIC T4 Gc
Ambient Range : 0°C ≤ Tamb ≤60°C (For suffix without -T)
Ambient Range : -40°C ≤ Tamb ≤75°C (For suffix with -T)
4. Standards covered:
ATEX: EN 60079-0:2012+A11:2013, EN 60079-15:2010
IECEx: IEC 60079-0 Ed.6; IEC 60079-15 Ed.4
5. The conditions of safe usage:
•The equipment shall only be used in an area of at least
pollution degree 2, as defined in IEC/EN 60664-1.
•The equipment shall be installed in an enclosure that provides
a minimum ingress protection of IP 54 in accordance with
IEC/EN 60079-0.
•Conductors suitable for Rated Cable Temperature ≥ 100°C
•Input conductor with 28-12 AWG (max. 3.3 mm2) to be used
with the devices
Address of manufacturer: Fl. 4, No. 135, Lane 235, Baoqiao Rd.
Xindian Diist., New Taipei City, 23145, Taiwan, R.O.C.