Moxa Technologies MGate 5101-PBM-MN User manual

P/N: 1802051010012
*1802051010012*
MGate 5101-PBM-MN
Quick Installation Guide
Edition 3.0, May 2016
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll
-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax:
1-714-528-6778
Moxa China (Shanghai office):
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe:
Tel:
[phone]
Fax:
[phone]
Moxa Asia-Pacific:
Tel:
[phone]
Fax:
[phone]
Moxa India:
Tel:
[phone]
Fax:
[phone]

2016 Moxa Inc. All rights reserved.

- 2 -
Overview
The MGate 5101-PBM-MN is an industrial Ethernet gateway for PROFIBUS
and Modbus TCP network communication.
Package Checklist
Before installing the MGate 5101-PBM-MN, verify that the package
contains the following items:
•1 MGate 5101-PBM-MN gateway
•Documentation and Software CD
•Quick Installation Guide (printed)
•Product Warranty Statement
Please notify your sales representative if any of the above items are
missing or damaged.
Optional Accessories (can be purchased separately):
•CBL-F9M9-150: DB9-female-to-DB9-male serial cable, 150 cm
•CBL-F9M9-20: DB9-female-to-DB9-male serial cable, 20 cm
•Mini DB9F-to-TB: DB9-female-to-terminal-block connector
•WK-36-01: Wall-mounting kit
Hardware Introduction
LED Indicators
LED
Color
Function
PWR1
Green
Power is on
Off
Power is off
PWR2
Green
Power is on
Off
Power is off
Ready
Green
Steady on: Power is on and the MGate is functioning
normally
Blinking: The MGate has been located by the MGate
Manager’s Location function
Red
Steady on: Power is on and the MGate is booting up
Blinking: Indicates an IP conflict, or the DHCP or
BOOTP server is not responding properly
Off
Power is off or fault condition exists
COMM
Off
No data exchange
Green
Data exchange with all slaves
Green,
flashing
Data exchange with at least one slave (not all
configured slaves can communicate with gateway)
Red
Bus control error
CFG
Off
No PROFIBUS configuration
Green
PROFIBUS configuration OK
PBM
Off
PROFIBUS master is offline
Red
PROFIBUS master is in STOP mode
Green,
flashing
PROFIBUS master is in CLEAR mode
Green
PROFIBUS master is in OPERATE mode
TOK
Green
Gateway holds the PROFIBUS token

- 3 -
LED
Color
Function
Off
Gateway is waiting for the PROFIBUS token
Ethernet
Amber Steady: 10Mbps, no data is transmitting
Blinking: 10Mbps, data is transmitting
Green
Steady: 100Mbps, no data is transmitting
Blinking: 100Mbps, data is transmitting
Off
Ethernet cable is disconnected
Reset Button
The reset button is used to load factory defaults. Use a pointed object
such as a straightened paper clip to hold the reset button down for five
seconds. Release the reset button when the Ready LED stops blinking.
Hardware Installation Procedure
STEP 1
:
C
onnect the power adapter. Connect the 12-
48 VDC power line
or DIN
-rail power supply with the MGate 5101-PBM-MN
device’s terminal block.
STEP 2:
Use a PROFIBUS cable to connect the unit to a PROFIBUS slave
device.
STEP 3
:
Connect
the unit to the Modbus TCP device.
STEP 4:
The MGate 5101-PBM-MN series is designed to be attached to
a DIN
rail or mounted on a wall. For DIN-rail
mounting, push
down the spring and properly attach it to the
DIN-
rail until it
“snaps” into place. For wall
mounting, install the wall-mount
kit (optional) first
and then screw the device onto the wall.

- 4 -
The following figure illustrates the two mounting options:
Software Installation Information
To install MGate Manager, insert the MGate Document & Software CD into
your PC’s CD-ROM drive. Once the installation window opens, click the
Installation button and follow the onscreen instructions. For more
detailed information about MGate Manager, click the Documents button
and select the MGate 5101-PBM-MN User’s Manual.
Pin Assignments
PROFIBUS Serial Port (Female DB9)
PIN
Signal Name
1
–
2
–
3
PROFIBUS D+
4
RTS
5
Signal common
6
5V
7
–
8
PROFIBUS D-
9
–
Power Input and Relay Output Pinouts
V2+ V2-
V1+ V1-
Shielded
Ground
DC
Power
Input 2
DC
Power
Input 2
N.O. Common N.C.
DC
Power
Input 1
DC
Power
Input 1

- 5 -
Specifications
Power Requirements
Power Input
12 to 48 VDC
Power Consumption
365 mA @ 12 VDC, 100 mA @ 48 VDC
Operating Temperature
0 to 60°C (32 to 140°F)
-40 to 75°C (-40 to 167°F) for –T model
Operating Humidity
5 to 95% RH
Dimensions
36 x 105 x 140 mm (1.42 x 4.13 x 5.51 in)
Reliability
Alert Tools
Built-in buzzer and RTC
MTBF
540,026 hrs.
ATEX: DEMKO 14 ATEX 1288X Rev. 0
IECEx: IECEx UL 14.0023X
Marking string: Ex nA nC IIC T4 Gc
Standards covered:
EN 60079-0: 2012+A11:2013/IEC 60079-0: Ed 6.0
EN 60079-15:2010/IREC 60079-15: Ed 4.0
Ambient temperature range:
0°C to 60°C (For models without suffix –T)
-40°C to 75°C (For models with suffix –T only)
Field-wiring connection:
The device uses a terminal block, solder on the power distribution board,
suitable for 12-24 AWG wire size, torque value 4.5 lb-in( 0.51 N-m).
Battery information: Battery is not user replaceable.
Installation instructions:
•A 4 mm2conductor must be used when the connection to the external
grounding screw is utilized.
•Conductors suitable for use at an ambient temperature of 84°C must
be used for the power supply terminal.
Special conditions for safe use:
•The device is to be installed in an IECEx/ATEX Certified IP54
enclosure and accessible only through the use of a tool.
•The device is for use in an area of not more than pollution degree 2 in
accordance with IEC 60664-1.
For installations in hazardous locations (Class 1, Division 2):
•Devices are to be installed in an enclosure with a tool-removable
cover or door, suitable for the environment.
•The equipment must be suitable for use in Class 1, Division 2, Groups
A, B, C, D, or nonhazardous locations only.
•WARNING - EXPLOSION HAZARD - Do not disconnect equipment
unless power has been switched off or the area is known to be
nonhazardous.
•WARNING - EXPLOSION HAZARD - Substitution of any components
may impair suitability for Class 1, Division 2.

- 6 -
•WARNING - EXPOSURE TO SOME CHEMICALS MAY DEGRADE THE
SEALING PROPERTIES OF THE MATERIALS USED IN THE FOLLOWING
DEVICE: Sealed Relay Device U21.
Moxa Inc.
Fl. 4, No. 135, Lane 235, Baoqiao Rd.
Xindian Dist., New Taipei City, 23145
Taiwan, R.O.C.