Moxa Technologies MGate 5101-PBM-MN User manual

– 1 – – 2 – – 3 –
P/N: 1802051010010
MGate 5101-PBM-MN
Quick Installation Guide
First Edition, August 2012
Overview
The MGate 5101-PBM-MN is an industrial Ethernet gateway for
PROFIBUS and Modbus TCP network communication.
Package Checklist
Before installing the MGate 5101-PBM-MN, verify that the package
contains the following items:
•1 MGate 5101-PBM-MN gateway
•Documentation & Software CD
•Quick Installation Guide
•Product Warranty Statement
Optional Accessories:
•DR-45-24: 45W/2A DIN-rail 24 VDC power supply with
universal 85 to 264 VAC input.
•DR-75-24: 75W/3.2A DIN-rail 24 VDC power supply with
universal 85 to 264 VAC input.
•DR-120-24: 120W/5A DIN-rail 24 VDC power supply with 88 to
132 VAC/176 to 264 VAC input by switch.
•WK-36-01: Wall mounting kit
Please notify your sales representative if any of the above items is
missing or damaged.
Hardware Introduction
LED Indicators
LED Color Function
PWR1 Green Power is on
Off Power is off
PWR2 Green Power is on
Off Power is off
Ready
Green
Steady on: Power is on and the MGate is
functioning normally
Blinking: The MGate has been located by
the MGate Manager’s Location function
Red
Steady on: Power is on and the MGate is
booting up
Blinking: Indicates an IP conflict, or DHCP
or BOOTP server is not responding
properly
Off Power is off or fault condition exists
COMM
Off No data exchange
Green Data exchange with all slaves
Green,
flashing
Data exchange with at least one slave
(not
all configured slaves can communicate
with gateway)
Red Bus control error
CFG Off No PROFIBUS configuration
Green PROFIBUS configuration OK
PBM
Off PROFIBUS master is offline
Red PROFIBUS master is in STOP mode
Green,
flashing PROFIBUS master is in CLEAR mode
Green PROFIBUS master is in OPERATE mode
TOK
Green Gateway holds the PROFIBUS token
Off Gateway is waiting for the PROFIBUS
token
Ethernet
Amber Steady: 10Mbps, no data is transmitting
Blinking: 10Mbps, data is transmitting
Green Steady: 100Mbps, no data is transmitting
Blinking: 100Mbps, data is transmitting
Off Ethernet cable is disconnected
Reset Button
The reset button is used to load factory defaults. Use a pointed
object such as a straightened paper clip to hold the reset button
down for five seconds. Release the reset button when the Ready
LED stops blinking.
Hardware Installation Procedure
STEP 1:Connect the power adaptor. Connect the 12-48 VDC
power line or DIN-rail power supply with the MGate
5101-PBM-MN device’s terminal block.
STEP 2:Use a PROFIBUS cable to connect the unit to
PROFIBUS
slave device.
STEP 3:Connect the unit to the Modbus TCP device.
STEP 4:The MGate 5101-PBM-MN series is designed to be
attached to a DIN-rail or mounted on a wall. For DIN-rail
mounting, push down the sprin
g and properly attach it to
the DIN-rail until it “snaps” into place. For wall
mounting,
install the wall mount kit (optional) first, and then screw
the device onto the wall. The following figure illustrates
the two mounting options:

– 4 – – 5 – – 6 –
www.moxa.com/support
The Americas:
[phone] (toll-free: 1-888-669-2872)
Europe:
[phone]
Asia-Pacific:
[phone]
China:
[phone] (toll-free: 800-820-5036)
2012 Moxa Inc. All rights reserved.
Software Installation Information
To install MGate Manager, insert the MGate Document & Software
CD into your PC’s CD-ROM drive. Once the installation window
opens, click the Installation button and follow the onscreen
instructions. For more detailed information about MGate Manager,
click the Documents button and select the MGate 5101-PBM-MN
User’s Manual.
Pin Assignments
PROFIBUS Serial Port (Female DB9)
PIN Signal Name
1 N.C.
2 N.C.
3 PROFIBUS D+
4 RTS
5 Signal common
6 5V
7 N.C.
8 PROFIBUS D-
9 N.C.
Power Input and Relay Output Pinouts
V2+ V2- V1+ V1-
Shielded
Ground
DC
Power
Input 2
DC
Power
Input 2
N.O. Common
N.C.
DC
Power
Input 1
DC
Power
Input 1
Specifications
Power Requirements
Power Input
12 to 48 VDC
Power Consumption MGate 5101-PBM-MN: 365 mA @ 12 VDC
,
100 mA @ 48 VDC
Operating Temperature 0 to 60°C (32 to 140°F)
-40 to 75°C (-40 to 167°F) for –T model
Operating Humidity 5 to 95% RH
Dimensions
36 x 105 x 140 mm (1.42 x 4.13 x 5.51 in)
Reliability
Alert Tools
Built-in buzzer and RTC
MTBF 540,026 hrs