Moxa Technologies MGate 5105-MB-EIP User manual

P/N: 1802051050011
*1802051050011*
MGate 5105-MB-EIP
Quick Installation Guide
Edition 2.1, May 2016
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll
-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax:
1-714-528-6778
Moxa China (Shanghai office):
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe:
Tel:
[phone]
Fax:
[phone]
Moxa Asia-Pacific:
Tel:
[phone]
Fax:
[phone]
Moxa India:
Tel:
[phone]
Fax:
[phone]

2016 Moxa Inc. All rights reserved.

- 2 -
Overview
The MGate 5105-MB-EIP is an industrial Ethernet gateway for Modbus
RTU/ASCII/TCP and EtherNet/IP network communications.
Package Checklist
Before installing the MGate 5105-MB-EIP, verify that the package
contains the following items:
•1 MGate 5105-MB-EIP gateway
•RJ45 to DB9 cable (for console use)
•Documentation and software CD
•Quick installation guide (printed)
•Warranty card
Optional Accessories:
•DR-45-24: 45W/2A DIN-rail 24 VDC power supply with universal 85
to 264 VAC input
•DR-75-24: 75W/3.2A DIN-rail 24 VDC power supply with universal 85
to 264 VAC input
•DR-120-24: 120W/5A DIN-rail 24 VDC power supply with 88 to 132
VAC/176 to 264 VAC input by switch
•WK-36-02: Wall-mounting kit
•Mini DB9F-to-TB Adapter: DB9-female-to-terminal-block adapter
Please notify your sales representative if any of the above items are
missing or damaged.

- 3 -
Hardware Introduction
LED Indicators
LED
Color
Description
Ready
Off
Power is off or a fault condition exists
Green
Steady: Power is on, and the MGate is functioning
normally
Blinking: The MGate has been located by the
MGate Manager’s Location function
Red
Steady: Power is on, and the MGate is booting up
Blinking slowly: Indicates an IP conflict, or the
DHCP or BOOTP server is not responding properly
Flashing quickly: microSD card failed
EIP
(Scanner)
Off
No I/O data is exchanged
Green
Steady: I/O data is exchanged with all devices
Blinking: I/O data is exchanged with at least one
device (not all configured devices can
communicate with gateway)
EIP
(Adapter)
Off
No I/O data is exchanged
Green
Steady: I/O data is exchanged with all devices
Blinking: I/O data is exchanged with at least one
device (not all configured devices can
communicate with gateway)
MB
Off
No communication with Modbus device
Green
Modbus communication in progress
Red
Communication error
When MGate 5105 acts as Master:
1. Slave device returned an error (exception)
2.
Received frame error (parity error, checksum
error)
3. Timeout (slave device no response)
When MGate 5105 acts as Slave:
1. Received invalid function code
2. Master accessed invalid register address or
coil addresses
3. Received frame
error (parity error, checksum
error)

- 4 -
Dimensions
Unit: mm (inch)
Reset Button
Restore the MGate to factory default settings by using a pointed object
(such as a straightened paper clip) to hold the reset button down until the
Ready LED stops blinking (approx. five seconds).
Pull-high, Pull-low, and Terminator for RS-485
Remove the MGate 5105-MB-EIP’s top cover and you will find DIP
switches to adjust each serial port’s pull-high resistor, pull-low resistor,
and terminator.
SW
1
2
3
Pull-high
resistor
Pull-low
resistor
Terminator
ON
1 kΩ
1 kΩ
120 Ω
OFF
150 kΩ*
150 kΩ*
–*
*Default
Hardware Installation Procedure
1. Connect the power adapter. Connect the 12-48 VDC power line or
DIN-rail power supply to the MGate 5105-MB-EIP device’s terminal
block.
2. Use a Modbus serial cable to connect the MGate to a Modbus slave
device.
3. Use an Ethernet cable to connect the MGate to the EtherNet/IP
controller.
4. The MGate 5105-MB-EIP is designed to be attached to a DIN rail or
mounted on a wall. For DIN-rail mounting, push down the spring and
properly attach it to the DIN rail until it “snaps” into place. For wall
mounting, install the wall-mount kit (optional) first and then screw
the device onto the wall. The following figure illustrates the two
mounting options:

- 5 -
Software Installation Information
To install MGate Manager, insert the MGate Documentation and Software
CD into your PC’s CD-ROM drive. Then, run the following setup program
to begin the installation process from the “Software” directory:
MGM_Setup_[Version]_Build_[DateTime].exe
The filename of the latest version may have the following format:
MGM_Setup_Verx.x.x_Build_xxxxxxxx.exe.
For detailed information about MGate Manager, refer to the MGate
5105-MB-EIP User's Manual, which can be found in the “Document”
directory.
Pin Assignments
Modbus Serial Port (Male DB9)
Pin RS-232
RS-422/
RS-485 (4W)
RS-485 (2W)
1
DCD
TxD-(A)
–
2
RXD
TxD+(B)
–
3
TXD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5
GND
GND
GND
6
DSR
–
–
7
RTS
–
–
8
CTS
–
–
9
–
–
–
Ethernet Port (RJ45)
Pin
Signal
1
Tx+
2
Tx-
3
Rx+
6
Rx-

- 6 -
Power Input and Relay Output Pinouts
V2+ V2- V1+ V1-
Shielded
Ground
DC
Power
Input 2
DC
Power
Input 2
N.O. Common N.C.
DC
Power
Input 1
DC
Power
Input 1
Specifications
Power Requirements
Power Input
12 to 48 VDC
Power Consumption
455 mA @ 12 VDC, 125 mA @ 48 VDC
Operating Temperature
Standard models:
Wide temp. models:
0 to 60°C (32 to 140°F)
-40 to 75°C (-40 to 167°F) for –T model
Ambient Relative Humidity
5 to 95% RH
Dimensions
36 x 105 x 140 mm (1.42 x 4.13 x 5.51 in)
Reliability
Alert Tools
Built-in buzzer and RTC
MTBF
513,139 hrs.
1. DEMKO Certification number: 13 ATEX 1307610X
IEC Certification Number: IECEx UL 13.0051X;
2. Ambient Temperature Range: (-40°C ≤ Tamb ≤ 75°C)
3. Certification String: Ex nA nC IIC T3 Gc
4. Standards Covered: EN 60079-0:2013/IEC 60079-0 6th Ed. AND EN
60079-15:2010/IEC 60079-15 4th Ed.
5. The conditions of safe usage:
a. The Ethernet Communications Devices are intended for mounting
in a tool-accessible IP54 enclosure and used in an area of not
more than pollution degree 2 as defined by IEC 60664-1.
b. Conductors suitable for use in an ambient temperature greater
than 86°C must be used for the power supply terminal.
c. A 4mm2conductor must be used when a connection to the
external grounding screw is utilized.
d. Provisions shall be made, either in the equipment or external to
the equipment, to prevent the peak-rated voltage being
exceeded by transient disturbances of more than 140%.
Terminal Block (plug matched with socket): rated at 300 V, 15 A, 105°C,
12-28 AWG (0.0804 mm2- 3.31 mm2) wire size, torque value 4.5 lb-in
(0.509 N-m). The input terminal cable size:14 AWG (2.1 mm2).
For HazLoc installation (Class I, Division 2):
•Devices are to be installed in an enclosure with a tool-removable
cover or door, suitable for the environment.

- 7 -
•The equipment must be suitable for use in Class I, Division 2, Groups
A, B, C, D, or nonhazardous locations only.
•WARNING - EXPLOSION HAZARD - Do not disconnect equipment
unless power has been switched off or the area is known to be
nonhazardous.
•WARNING - EXPLOSION HAZARD - Substitution of any components
may impair suitability for Class I, Division 2.
•WARNING - EXPOSURE TO SOME CHEMICALS MAY DEGRADE THE
SEALING PROPERTIES OF THE MATERIALS USED IN THE FOLLOWING
DEVICE: Sealed Relay Device U21.
Moxa Inc.
Fl. 4, No. 135, Lane 235, Baoqiao Rd.
Xindian Dist., New Taipei City, 23145
Taiwan, R.O.C.