Moxa Technologies MGate 5111 User manual

MGate 5111
User’s Manual
Edition 1.0, December 2017
www.moxa.com/product
© 2017 Moxa Inc. All rights reserved.

MGate 5111 User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in accordance with
the terms of that agreement.
Copyright Notice
© 2017 Moxa Inc. All rights reserved.
Trademarks
The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the part of
Moxa.
Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited
to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the
products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for
its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Americas
Toll
-free: 1-888-669-2872
Tel:
[phone]
Fax:
[phone]
Moxa China (Shanghai office)
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe
Tel:
[phone]
Fax: [phone]
Moxa Asia
-Pacific
Tel:
[phone]
Fax: [phone]
Moxa India
Tel:
[phone]
Fax:
[phone]

Table of Contents
1. Introduction...................................................................................................................................... 1-1
Overview ...........................................................................................................................................1-2
Package Checklist ...............................................................................................................................1-2
Product Features ................................................................................................................................1-3
2. Getting Started.................................................................................................................................. 2-1
Connecting the Power .........................................................................................................................2-2
Connecting PROFIBUS Devices ............................................................................................................. 2-2
Connecting Serial Devices....................................................................................................................2-2
Connecting to a Host or the Network.....................................................................................................2-2
Installing the Software (Optional) .........................................................................................................2-2
Wiring Requirements...........................................................................................................................2-3
LED Indicators....................................................................................................................................2-4
Dimensions ........................................................................................................................................2-5
Pull Up/Down Resistors for RS-485 (Modbus) .........................................................................................2-5
Pin Assignments .................................................................................................................................2-6
Power Input and Relay Output Pinouts...................................................................................................2-6
Hardware Installation ..........................................................................................................................2-7
Specifications .....................................................................................................................................2-7
microSD Card.....................................................................................................................................2-9
Backing Up a Configuration......................................................................................................... 2-10
Configuring an MGate (Mass deployment/Replacement) ................................................................. 2-10
microSD card Write Failure ......................................................................................................... 2-10
Quick Setup ..................................................................................................................................... 2-10
Step 1: System Setting .............................................................................................................. 2-10
Step 2: Select Protocol............................................................................................................... 2-11
Step 3: PROFIBUS Slave Settings ................................................................................................ 2-12
Step 4: Modbus TCP Settings...................................................................................................... 2-13
Step 5: Finish ........................................................................................................................... 2-14
3. Device Search Utility ......................................................................................................................... 3-1
Installing the Software ........................................................................................................................3-2
Starting the Device Search Utility (DSU)................................................................................................3-5
Broadcast Search ........................................................................................................................3-6
Search IP ...................................................................................................................................3-7
Locate........................................................................................................................................3-8
Assign IP.................................................................................................................................... 3-8
Unlock ....................................................................................................................................... 3-8
Import/Export............................................................................................................................. 3-9
Upgrading the Firmware ...............................................................................................................3-9
4. Web Console Configuration ............................................................................................................... 4-1
Overview ...........................................................................................................................................4-2
Basic Settings ....................................................................................................................................4-2
Network Settings ................................................................................................................................4-3
Serial Settings....................................................................................................................................4-4
Protocol Settings ................................................................................................................................4-5
System Management......................................................................................................................... 4-12
Accessible IP Settings ................................................................................................................ 4-12
DoS Defense............................................................................................................................. 4-13
System Log Settings .................................................................................................................. 4-14
Auto Warning Settings ............................................................................................................... 4-15
E-mail Alert Settings.................................................................................................................. 4-15
SNMP Trap Settings ................................................................................................................... 4-16
SNMP Agent Settings ................................................................................................................. 4-16
LLDP Settings ........................................................................................................................... 4-17
Certificate ................................................................................................................................ 4-18
Misc. Settings ........................................................................................................................... 4-18
Maintenance ............................................................................................................................. 4-20
System Monitoring............................................................................................................................ 4-22
System Status .......................................................................................................................... 4-22
Protocol Status ......................................................................................................................... 4-23
Fault Protection and Status Monitoring ......................................................................................... 4-26
Restart ............................................................................................................................................ 4-27
Logout............................................................................................................................................. 4-27
MXview ........................................................................................................................................... 4-27
MXconfig ......................................................................................................................................... 4-27

1
1. Introduction
Welcome to the MGate 5111 gateway series that converts Modbus/PROFINET/EtherNet/IP to PROFIBUS slave
protocols.
All the MGate 5111 gateways have dual DC power input for redundancy. Magnetic serial port isolation is also
provided.
In this chapter, we give an introduction to the MGate 5111. The following topics are covered in this chapter:

Overview

Package Checklist

Product Features

MGate 5111 Introduction
1-2
Overview
The MGate 5111 Series consists of industrial Ethernet gateways that convert between Modbus RTU/ASCII/TCP,
EtherNet/IP, PROFINET and PROFIBUS protocols. All models are protected with a rugged metallic casing, are
DIN-rail mountable, and offer built-in serial isolation. Modbus is one of the most widely used industrial
communication protocol, and EtherNet/IP, PROFINET and PROFIBUS protocols are commonly seen in factory
automation and process automation. The MGate 5111 gateways support both Modbus RTU/ASCII/TCP master
or slave modes, so you can easily connect your Modbus device to PROFIBUS PLCs or DCSs, such as Siemens
PLCs. For system integration, the MGate 5111 helps you connect EtherNet/IP PLC/SCADA, for example
Rockwell Automation PLCs, to PROFIBUS PLC/DCS system, or between a new Siemens PLC system that
supports PROFINET to an existing PROFIBUS system. The MGate 5111 gateways, designed for easy
configuration and quick maintenance, provide a web console for remote maintenance, a wizard UI to help you
set up the gateway quickly, and build-in comprehensive troubleshooting tools to reduce configuration time or
system downtime. The rugged design is suitable for industrial applications such as factory automation, power,
oil & gas, water and wastewater, and other process automation industries.
The MGate 5111 Series of gateways has LED indicators and supports Protocol Diagnose and Traffic Monitor for
easy troubleshooting, especially during the installation stage. Communication issues could be caused by
incorrect software parameters, such as slave ID and register address, or incorrect command configuration.
With Protocol Diagnose and Traffic Monitor, you can check the captured data and easily identify the root cause.
The MGate 5111 Series of gateways also supports status monitoring and fault protection. The status monitoring
function notifies a PLC/DCS/SCADA system when a Modbus device gets disconnected or does not respond, in
which case the process PLC/DCS gets the status of each end device and then issues an alarm to notify operators.
The fault protection function executes actions to end devices with a pre-defined value set by the user when a
PROFIBUS cable gets disconnected.
Windows-Based Utility and Web Console for Easy Setup
A Windows-based utility is provided to make it easy to search for and locate devices, assign IP addresses,
import/export configuration files, and upgrade the MGate 5111’s firmware. The utility automatically connects
to all available MGate 5111 units on the local area network (LAN). A user-friendly web console is provided to
configure the device from a web browser.
Package Checklist
All models in the MGate 5111 series are shipped with the following items:
Standard Accessories
•MGate 5111 gateway
•Quick installation guide
•Product warranty statement
Optional Accessories
•Mini DB9F-to-TB Adapter: DB9 female to terminal block adapter for RS-422/485 applications
•WK-51-01: wall-mounting kit, 51 mm wide
NOTE
Notify your sales representative if any of the above items is missing or damaged.

MGate 5111 Introduction
1-3
Product Features
•Supports PROFIBUS DP V0 slave
•Supports Modbus RTU/ASCII/TCP master or slave
•Supports EtherNet/IP adapter or PROFINET IO device
•Built-in traffic monitoring/diagnostics/status monitoring and fault protection
•Built-in Ethernet cascading for easy wiring
•Redundant dual DC power inputs and relay output supported
•microSD card for configuration backup/duplication, and event log
•Serial port with 2 kV built-in isolation protection
•-40 to 75°C wide operating temperature models available
•Security features based on IEC-62443

2
2. Getting Started
This chapter provides basic instructions for installing the MGate 5111.
The following topics are covered in this chapter:

Connecting the Power

Connecting PROFIBUS Devices

Connecting Serial Devices

Connecting to a Host or the Network

Installing the Software (Optional)

Wiring Requirements

LED Indicators

Dimensions

Pull Up/Down Resistors for RS-485 (Modbus)

Pin Assignments

Power Input and Relay Output Pinouts

Hardware Installation

Specifications

microSD Card
Backing Up a Configuration
Configuring an MGate (Mass deployment/Replacement)
microSD card Write Failure

Quick Setup
Step 1: System Setting
Step 2: Select Protocol
Step 3: PROFIBUS Slave Settings
Step 4: Modbus TCP Settings
Step 5: Finish

MGate 5111 Getting Started
2-2
Connecting the Power
1. The unit can be powered by connecting a power source to the terminal block.
2. The power input range is from 12 to 48 VDC.
To remove the wire from the terminal block, use a flathead screwdriver to push the orange slot next to the
terminal block hole, and then pull the wire out.
Note that the unit does not have an on/off switch. It automatically turns on when it receives power. The PWR
LED on the front panel will glow to indicate that the unit is receiving power. There are two DC power inputs for
redundancy.
Connecting PROFIBUS Devices
The unit’s PROFIBUS port(s) are located on the front panel. Use a PROFIBUS cable to directly connect the unit
to a PROFIBUS PLC or other PROFIBUS master.
For the PROFIBUS port pin assignments, please refer to the Pin Assignments section. This information can
then be used to construct your own PROFIBUS cable.
Connecting Serial Devices
The unit’s serial port(s) are located on the front panel. If you are connecting an RS-485 multidrop network with
multiple devices, note the following:
•All devices that are connected to a single serial port must use the same protocol (i.e., either Modbus RTU
or Modbus ASCII).
For serial port pin assignments, refer to the Pin Assignments section.
Connecting to a Host or the Network
Two 10/100 BaseT Ethernet ports are located on the gateway’s front panel. These ports are used to connect the
unit to a host or Ethernet network, as follows:
•For normal operation, use a standard straight-through Ethernet cable to connect the unit to your Modbus
TCP, EtherNet/IP, or PROFINET network.
•For initial configuration or for troubleshooting purposes, you may connect the unit directly to a PC.
The unit’s Link LED will light up to indicate a live Ethernet connection.
Installing the Software (Optional)
The Device Search Utility (DSU) can be downloaded from Moxa’s website: www.moxa.com. The DSU can be
used to connect the MGate with the PC. For additional details, refer to Chapter 3: Device Search Utility.

MGate 5111 Getting Started
2-3
Wiring Requirements
ATTENTION
Safety First!
Be sure to disconnect the power cord before installing and/or wiring your
MGate 5111.
Wiring Caution!
Calculate the
maximum possible current in each power wire and common wire. Observe all electrical codes
dictating the maximum allowed current for each wire size.
If the current goes over the allowed maximum, the wiring could overheat, causing serious damage to your
eq
uipment.
Temperature Caution!
Be careful when handling the
MGate 5111. When plugged in, the MGate 5111
’s internal components generate
heat, and consequently the board may be too hot to touch.
You should also observe the following common wiring rules:
•Use separate paths to route wiring for power and devices. If power wiring and device wiring paths must
cross, make sure the wires are perpendicular at the point of intersection.
NOTE
Do not run signal or communication wiring and power wiring in the same wire conduit. To avoid interference,
wires with different signal characteristics should be routed separately.
•You can use the type of signal transmitted through a wire to determine which wires should be kept separate.
The rule of thumb is that wiring that shares similar electrical characteristics can be bundled together.
•Keep input wiring and output wiring separate.
•When necessary, we strongly advise labeling wiring to all devices in the system.

MGate 5111 Getting Started
2-4
LED Indicators
LED Color Description
PWR 1,
PWR 2
Green Power is on
Off Power is off
Ready Green Steady on: Power is on, and the unit is functioning normally
Blinking: The unit is responding to the software’s Locate function
Red Steady on: Power is on, and the unit is booting up
Blinking: Indicates an IP conflict, or the DHCP or BOOTP server is not responding
properly
Flashing quickly: the microSD card failed
LAN Green
(Flashing only)
The Ethernet port is receiving or transmitting data
Modbus TCP Client: Modbus communication in progress
Modbus TCP Server: Modbus communication in progress
EtherNet/IP Adapter: EtherNet/IP communication is exchanging data
PROFINET IO Device:PROFINET communication is exchanging data
Red
(Flashing only)
A communication error occurred
Modbus TCP Client:
1. Received an exception code or framing error (parity error, checksum error)
2. Command timeout (slave device is not responding)
3. TCP connection timeout
Modbus TCP Server:
1. Received an invalid function code or framing error (parity error, checksum
error)
2. Accessed invalid register address or coil address
EtherNet/IP Adapter:
The connection was refused due to incorrect configuration
Off No communication
MB* Green
(Flashing only)
Modbus is receiving or transmitting data
Red
(Flashing only)
A communication error occurred
Master Mode:
1. Received an exception code or framing error (parity error, checksum error)
2. Command timeout (the slave device is not responding)
Slave Mode:
1. Received an invalid function code or framing error (parity error, checksum
error)
2. Accessed invalid register address or coil address
Off No communication
PBS Green
(Flashing only)
PROFIBUS is receiving or transmitting data
Red
(Steady)
An error in the Configuration or parameter data
Off PROFIBUS is offline or the slave ID is wrong.
Eth1, Eth2 Green Indicates an 100 Mbps Ethernet connection
Amber
Indicates a 10 Mbps Ethernet connection
Off The Ethernet cable is disconnected
*Only indicates serial communication status; for Modbus TCP status, please refer to LAN LED indicator.

MGate 5111 Getting Started
2-5
Dimensions
Unit = mm (inch)
Pull Up/Down Resistors for RS-485 (Modbus)
In some critical environments, you may need to add termination resistors to prevent the reflection of serial
signals. When using termination resistors, it is important to set the pull up/down resistors correctly so that the
electrical signal is not corrupted. The MGate 5111 uses DIP switches to set the pull up/down resistor values for
each serial port.
To add a 120 Ω termination resistor, set switch 3 on the port’s assigned DIP switch to ON; set switch 3 to
OFF (the default setting) to disable the termination resistor.
To set the pull up/down resisto rs to 150 KΩ, set switches 1 and 2 on the port’s assigned DIP switch to OFF.
This is the default setting.
To set the pull up/down resistors to 1 KΩ, set switches 1 and 2 on the port’s assigned DIP switch to ON.
ATTENTION
Do not use the 1 KΩ pull
up/down setting on the MGate 5111 when using the RS-
232 interface. Doing so will
degrade the RS
-232 signals and reduce the effective communication distance.
On the MGate 5111’s left side panel, you will find DIP switches to adjust each serial
port’s pull
-up resistor, pull-down resistor, and terminator.

MGate 5111 Getting Started
2-6
SW MODBUS
1 2 3
Pull-up resistor Pull-down resistor Terminator
ON 1 kΩ 1 kΩ 120 Ω
OFF 150 kΩ (default) 150 kΩ (default) – (default)
Pin Assignments
The MGate 5111 uses DB9 serial ports to connect to Modbus RTU or ASCII devices. Each port supports three
serial interfaces that is selected by software: RS-232, RS-422, and RS-485 (both 2 and 4-wire).
RJ45 (Ethernet, Console)
Pin Ethernet Console (RS-232)
1 Tx+ DSR
2 Tx- RTS
3 Rx+ GND
4 – TxD
5 – RxD
6 Rx- DCD
7 – CTS
8 – DTR
Male DB9 (Serial port)
Pin RS-232 RS-422/RS-485-4W RS-485-2W
1 DCD TxD-(A) –
2 RxD TxD+(B) –
3 TxD RxD+(B) Data+(B)
4 DTR RxD-(A) Data-(A)
5* GND GND GND
6 DSR – –
7 RTS – –
8 CTS – –
9
–
–
–
*Signal ground
PROFIBUS Port (Female DB9)
Pin CAN
1 N.C.
2 N.C.
3 PROFIBUS D+
4 RTS
5 Signal common
6 5V
7 N.C.
8 PROFIBUS D-
9 N.C.
Power Input and Relay Output Pinouts

MGate 5111 Getting Started
2-7
V2+ V2- V1+ V1-
DC Power Input 2 DC Power Input 2 N.O. Common N.C. DC Power Input 1 DC Power Input 1
Hardware Installation
The MGate 5111 is designed to be attached to a DIN rail or mounted on a wall. For DIN-rail mounting, push
down the spring and properly attach it to the DIN rail until it "snaps" into place. For wall mounting, install the
wall-mount kit (optional) first and then mount the device to the wall. The following figure illustrates the two
mounting options:
Specifications
Industrial Protocols
Protocols:
PROFIBUS, Modbus RTU/ASCII/TCP, PROFINET, EtherNet/IP
Protocol Conversion:
• Modbus RTU/ASCII (Master/Slave) to PROFIBUS slave
• Modbus TCP (Client/Server) to PROFIBUS slave
• EtherNet/IP (Adapter) to PROFIBUS slave
• PROFINET (IO Device) to PROFIBUS slave
Ethernet Interface
Protocols:
Modbus TCP (Client/Server), PROFINET (IO device),
EtherNet/IP (Adapter)
Number of Ports:
2 (1 IP address, supports Ethernet cascading)
Speed:
10/100 Mbps, Auto MDI/MDIX
Connector:
8-pin RJ45
Magnetic Isolation Protection:
1.5 kV (built-in)
PROFIBUS Interface
Protocol:
PROFIBUS DP-V0 Slave
Number of Ports:
1
Connector:
DB9 Female
Data Rate:
9600 bps to 12 Mbps

MGate 5111 Getting Started
2-8
Isolation:
2 kV (built-in)
Rotary Switch: PROFIBUS address 0-99 (address 100-125 supported through software configuration)
Modbus Serial Interface
Protocols:
Modbus RTU/ASCII (Master/Slave)
Number of Ports:
1
Serial Standards:
RS-232/422/485, software selectable
Connectors: DB9 male
Pull
Up/Down Resistor for RS-485: 1 kΩ, 150 kΩ
Terminator for RS
-485: 120 Ω
Isolation:
2 kV (built-in)
Modbus Serial Communication Parameters
Data Bits:
8
Stop Bits:
1, 2
Parity:
None, Even, Odd, Space, Mark
Flow Control:
RTS/CTS, RTS Toggle (RS-232 only)
Baudrate:
50 bps to 921.6 kbps
Modbus Serial Signals
RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
RS
-422: Tx+, Tx-, Rx+, Rx-, GND
RS
-485-4w: Tx+, Tx-, Rx+, Rx-, GND
RS
-485-2w: Data +, Data -, GND
Modbus TCP Interface
Protocols:
Modbus TCP client/server
Functions Supported:
1, 2, 3, 4, 5, 6, 15, 16, 23
Max. Number of Commands:
128
Max. Number of Connections:
MGate as Modbus TCP Client: 32 connections
MGate as Modbus TCP Server: 16 connections
Max. Total I/O Data Size:
Input: 2048 bytes, Output: 2048 bytes
EtherNet/IP Interface
Class:
Adapter
CIP Objects Supported: Identity,
Message Router, Assembly,
Connection Manager, TCP/IP interface, Ethernet link, Port
Max. Number of Connections:
• MGate as Adapter
:
1 connection for read/write
1 connection for read
-only
Max. Total I/O Data Size:
Input: 496 bytes; Output: 496 bytes
PROFINET Interface
Protocol:
PROFINET RT IO Device
Memory:
Input 512 bytes/output 512 bytes
Maximum No. of Connections:
1 master connection
Software
Configuration Options:
Web console, Serial console
Utility:
Device Search Utility (DSU) for Windows 95, 98, ME, NT, 2000,
Windows XP, Server 2003, Vista, Server 2008 (x86/x64), Windows
Server 2008 R2, Windows 7/8/8.1/10 (x86/x64), Windows Server 2012
(x64), Windows 2012 R2
Network Protocols:
TCP/IP, UDP, HTTP, HTTPS, SMTP, NTP, DNS,
DHCP Client, SNMP (v1, v2c, v3), MIB
-II, ARP, Telnet, SSH
Support:
MXview, MXconfig
Physical Characteristics
Housing:
Metal, IP30

MGate 5111 Getting Started
2-9
Weight:
589 g (1.30 lb)
Dimensions:
45.8 x 105 x 134 mm (1.8 x 4.13 x 5.28 in)
Storage Card Slot:
1 microSD (SDHC) card slot; supports up to 32 GB
Relay Alarm Circuit:
3-pin circuit with current carrying capacity of 2 A@ 30 VDC
Environmental Limits
Operating Temperature:
Standard Models:
0 to 60°C (32 to 140°F)
Wide Temp. Models:
-40 to 75°C (-40 to 167°F)
Storage Temperature:
-40 to 85°C (-40 to 185°F)
Ambient Relative Humidity:
5 to 95% (non-condensing)
Vibration:
IEC 60068-2-6, IEC 60068-2-64
Shock:
IEC 60068-2-27
Drop: IEC 60068-2-32
Power Requirements
Input Voltage:
12 to 48 VDC
Input Current:
416 mA max.
Power
Connector: Terminal block
Standards and Certifications
Safety:
EN 60950-1(LVD), UL 61010-2-201
Hazardous Location:
Class I Division 2, ATEX, IECEx
EMC:
EN 61000-6-2/6-4
EMI:
CISPR 22, FCC Part 15B Class A
EMS:
IEC 61000
-4-2 ESD: Contact: 8 kV; Air: 15 kV
IEC 61000
-4-3 RS: 80 MHz to 1 GHz: 10 V/m
IEC 61000
-4-4 EFT: Power: 4 kV; Signal: 4 kV
IEC 61000
-4-5 Surge: Power 2 kV; Signal: 2 kV
IEC 61000-4-6 CS: 150 kHz to 80 MHz: 10 V/m
IEC 61000
-4-8 PFMF: 30 A/m
Reliability
Alarm Functions:
Relay, email, SNMP trap
Alert Tools:
Built-in buzzer
MTBF (mean time between failures)
Time:
718,131 hrs
Standard
: Telcordia SR332
Warranty
Warranty Period:
5 years
Details: See www.moxa.com/warranty
microSD Card
The MGate 5111 gateway series is equipped with a microSD card slot for easy configuration. The microSD card
can be used to store an MGate’s system configuration settings and the MGate’s system log. In addition, a
configuration stored on a microSD card can be uploaded automatically to an MGate.
NOTE
Inserting a microSD card into an MGate’s microSD slot results in one of two actions, depending on what kind of
data is currently stored on the card:
1.
If the microSD card contains a valid configuration file, the configuration wil
l be automatically copied to the
MGate.
2.
If the microSD card does not contain a valid configuration file (e.g., if it’s empty), the MGate’s configuration
will be copied to the microSD card.

MGate 5111 Getting Started
2-10
Backing Up a Configuration
Use the following procedure to copy the configuration of an MGate gateway to a microSD card:
1. Use a PC to format the microSD card to support FAT file systems and delete all of the data on the card.
2. Power off the MGate and insert the microSD card (make sure the microSD card is empty).
3. Power on the MGate. The current settings will be copied to the microSD card.
4. If you modify the MGate’s configuration using the Web Console while the microSD card is installed in the
gateway, your configuration changes will be automatically saved to the microSD card when you save the
configuration.
Configuring an MGate (Mass deployment/Replacement)
Use the following procedure to copy the configuration stored on a microSD card to an MGate gateway for mass
deployment or to replace a faulty unit:
1. Power off the MGate device (often a new device) and insert the microSD card.
2. Power on the MGate device.
3. The configuration file stored on the microSD card will be copied automatically to the MGate gateway.
microSD card Write Failure
The following events will cause the microSD card to experience a write failure.
1. The microSD card has less than 20 MB of free space.
2. The MGate configuration file is read-only.
3. The microSD card’s file system is corrupted.
4. The microSD card is damaged.
The MGate gateway will halt the write action if any of the above conditions exists. The MGate’s Ready LED will
flash and the beeper will sound to inform the user of the write failure. If you are replacing the microSD card, the
microSD card will be synchronized with the configurations stored on the MGate device. Note that the microSD
card should not contain any configuration files; otherwise, the configuration will be copied from the microSD
card to the MGate device.
WARNING
If your intention is to back up the configuration of an MGate gateway, it is best practice to
only insert an
empty microSD card
into the microSD slot. If the card contains a valid configuration file, that configuration
will automatically (w
ithout warning) overwrite the MGate’s current configuration.
Quick Setup
The MGate series now provides Quick Setup, an illustrated guide especially designed to make the configuration
easy. When you press Quick Setup, you will access the mode and start to configure. Only five steps are needed.
Step 1: System Setting
First, configure the Server Settings to identify the units and Network Settings of the MGate.

MGate 5111 Getting Started
2-11
Step 2: Select Protocol
Then, you have to select the protocols used on your devices that are connected through the MGate. After
selection, the MGate will automatically change its role to the correct one. For example, if the device is set as a
Modbus TCP Server, the MGate will then automatically configure as a Modbus TCP Client by itself. Regarding
protocol configuration, please refer to chapter 4.
Example of Role 1 and Role 2:
After finishing the device protocol selection, Role 1 and Role 2 of the MGate will be set accordingly. You will
need to configure the details on each side with the following steps. Here is an example of Role 1 as a PROFIBUS
Master, and Role 2 as a Modbus TCP Server device.

MGate 5111 Getting Started
2-12
Step 3: PROFIBUS Slave Settings
For details, please refer to Protocol Settings.

MGate 5111 Getting Started
2-13
Step 4: Modbus TCP Settings
For details, please refer to Protocol Settings.