Moxa Technologies ioLogik E1200 Series User manual

ioLogik E1200 Series User’s Manual
Eleventh Edition, April 2015
www.moxa.com/product
© 2015 Moxa Inc. All rights reserved.
Reproduction without permission is prohibited.

ioLogik E1200 Series User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in accordance with
the terms of that agreement.
Copyright Notice
Copyright © 2015 Moxa Inc.
All rights reserved.
Reproduction without permission is prohibited.
Trademarks
The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the part of
Moxa.
Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited
to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the
products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for
its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Americas
Toll-free: [phone]
Tel: [phone]
Fax: [phone]
Moxa China (Shanghai office)
Toll-free: [phone]
Tel: [phone]
Fax: [phone]
Moxa Europe
Tel: [phone]
Fax: [phone]
Moxa Asia-Pacific
Tel: [phone]
Fax: [phone]
Moxa India
Tel: [phone]
Fax: [phone]

Table of Contents
1. Introduction...................................................................................................................................... 1-1
Product Features ................................................................................................................................1-2
Inside the Box....................................................................................................................................1-2
Product Model Information ...................................................................................................................1-3
Product Specifications .........................................................................................................................1-4
Common Specifications ................................................................................................................1-4
ioLogik E1210 .............................................................................................................................1-5
ioLogik E1211 .............................................................................................................................1-5
ioLogik E1212 .............................................................................................................................1-6
ioLogik E1213 .............................................................................................................................1-7
ioLogik E1214 .............................................................................................................................1-8
ioLogik E1240 .............................................................................................................................1-9
ioLogik E1241 .............................................................................................................................1-9
ioLogik E1242 ........................................................................................................................... 1-10
ioLogik E1260 ........................................................................................................................... 1-11
ioLogik E1262 ........................................................................................................................... 1-11
Physical Dimensions.......................................................................................................................... 1-12
Hardware Reference.......................................................................................................................... 1-13
Panel Guide .............................................................................................................................. 1-13
Ethernet Port ............................................................................................................................ 1-13
LED Indicators .......................................................................................................................... 1-13
I/O Circuit Diagram........................................................................................................................... 1-14
DI Circuit ................................................................................................................................. 1-14
Sinking DO Circuit ..................................................................................................................... 1-14
Sourcing DO Circuit ................................................................................................................... 1-15
DIO Circuit ............................................................................................................................... 1-16
Relay Circuit ............................................................................................................................. 1-17
AI Circuit.................................................................................................................................. 1-17
RTD Circuit ............................................................................................................................... 1-17
TC Circuit ................................................................................................................................. 1-18
2. Initial Setup ...................................................................................................................................... 2-1
Hardware Installation ..........................................................................................................................2-2
Connecting the Power ..................................................................................................................2-2
Grounding the ioLogik E1200 ........................................................................................................2-2
DIN Rail, Wall Mounting ...............................................................................................................2-2
Connecting to the Network ...........................................................................................................2-3
Jumper Settings (DIO and AI).......................................................................................................2-3
I/O Wiring Diagrams....................................................................................................................2-5
ioSearch™ Installation.........................................................................................................................2-7
Load Factory Default Settings...............................................................................................................2-7
3. Using the Web Console...................................................................................................................... 3-1
Introduction to the Web Console...........................................................................................................3-2
Overview ...........................................................................................................................................3-3
Network Settings for the Web Console...................................................................................................3-4
General Settings .........................................................................................................................3-4
Ethernet Configuration .................................................................................................................3-4
User-Defined Modbus Addressing..........................................................................................................3-5
Default Modbus Address...............................................................................................................3-5
Active OPC Server Settings ..................................................................................................................3-6
Tag Generation...................................................................................................................................3-6
I/O Settings .......................................................................................................................................3-8
DI Channels................................................................................................................................3-8
DO Channels............................................................................................................................. 3-10
AI Channels.............................................................................................................................. 3-11
AI Input Range ......................................................................................................................... 3-12
AO Channels............................................................................................................................. 3-14
RTD Channels ........................................................................................................................... 3-15
TC Channels ............................................................................................................................. 3-17
System Management......................................................................................................................... 3-18
Accessibility IP List .................................................................................................................... 3-18
Network Connection................................................................................................................... 3-19
Firmware Update....................................................................................................................... 3-19
Import System Configuration Settings ......................................................................................... 3-19
Export System Settings.............................................................................................................. 3-20
Peer-to-Peer Networking.................................................................................................................... 3-20
Peer-to-Peer Settings (1-50)....................................................................................................... 3-20
Sample Peer-to-Peer Configuration .............................................................................................. 3-21
DO Safe Mode Settings .............................................................................................................. 3-22

AO Safe Mode Settings............................................................................................................... 3-22
SNMP .............................................................................................................................................. 3-22
SNMP Trap ............................................................................................................................... 3-22
Using SNMP .............................................................................................................................. 3-23
Change Password ............................................................................................................................. 3-27
Load Factory Defaults........................................................................................................................ 3-28
Save/Restart.................................................................................................................................... 3-28
4. Using ioSearch™................................................................................................................................ 4-1
Introduction to ioSearch™ ...................................................................................................................4-2
ioSearch™ Main Screen .......................................................................................................................4-2
Main Screen Overview..................................................................................................................4-2
ioSearch™ Setup ................................................................................................................................4-3
System ......................................................................................................................................4-3
Sort...........................................................................................................................................4-4
Quick Links.................................................................................................................................4-4
Main Function.....................................................................................................................................4-4
Locate........................................................................................................................................4-5
Firmware Upgrade .......................................................................................................................4-5
Unlock .......................................................................................................................................4-5
Import .......................................................................................................................................4-6
Export........................................................................................................................................4-6
Change IP Address ......................................................................................................................4-7
Batch TCP/IP Configuration on Multiple Devices...............................................................................4-7
Restart System ...........................................................................................................................4-8
Reset to Default ..........................................................................................................................4-8
Mass Deployment (Import)...........................................................................................................4-9
Mass Deployment (Export) ...........................................................................................................4-9
5. Active OPC Server ............................................................................................................................. 5-1
Introduction to Active OPC Server.........................................................................................................5-2
OLE for Process Control................................................................................................................5-2
Active OPC Server—From Pull to Push ............................................................................................5-3
Features of Active OPC Server ..............................................................................................................5-5
One Simple Click Creates Active Tags ............................................................................................5-5
Faster, More Accurate Data Collection than Traditional “Pull Technology”............................................5-5
Dynamic IP Assignments for Cellular RTUs......................................................................................5-6
Active OPC Server Setup .....................................................................................................................5-6
Installing Active OPC Server .........................................................................................................5-6
Main Screen Overview..................................................................................................................5-7
Menu Bar ...................................................................................................................................5-7
A. Modbus/TCP Default Address Mappings ............................................................................................ A-1
E1210 Modbus Mapping.......................................................................................................................A-2
E1211 Modbus Mapping.......................................................................................................................A-5
E1212 Modbus Mapping.......................................................................................................................A-7
E1213 Modbus Mapping..................................................................................................................... A-12
E1214 Modbus Mapping..................................................................................................................... A-16
E1240 Modbus Mapping.....................................................................................................................A-18
E1241 Modbus Mapping..................................................................................................................... A-20
E1242 Modbus Mapping..................................................................................................................... A-21
E1260 Modbus Mapping..................................................................................................................... A-24
E1262 Modbus Mapping..................................................................................................................... A-25
B. Network Port Numbers...................................................................................................................... B-1
C. Factory Default Settings.................................................................................................................... C-1
D. Pinouts.............................................................................................................................................. D-1
E. FCC Interference Statement.............................................................................................................. E-1
F. European Community (CE) ................................................................................................................ F-1

1
1. Introduction
The ioLogik E1200 industrial Ethernet remote I/O has two embedded Ethernet switch ports that allow
information to flow to another local Ethernet device or connect to the next ioLogik in the daisy-chain.
Applications such as factory automation, security and surveillance systems, and tunnel monitoring, can make
use of daisy-chained Ethernet for building multi-drop I/O networks over standard Ethernet cables and familiar
fieldbus protocols. The daisy-chain function on the ioLogik E1200 Ethernet remote I/O not only increases the
connections between machines and panels, but also lowers the cost of buying separate Ethernet switches, and
at the same time reduces labor fees and cabling by a large percentage. For example, if a production facility
contains 700 stations (20 points per station), the wiring cost reduction can reach 15% of the total
implementation cost.
The following topics are covered in this chapter:
Product Features
Inside the Box
Product Model Information
Product Specifications
Common Specifications
ioLogik E1210
ioLogik E1211
ioLogik E1212
ioLogik E1213
ioLogik E1214
ioLogik E1240
ioLogik E1241
ioLogik E1242
ioLogik E1260
ioLogik E1262
Physical Dimensions
Hardware Reference
Panel Guide
Ethernet Port
LED Indicators
I/O Circuit Diagram
DI Circuit
Sinking DO Circuit
Sourcing DO Circuit
DIO Circuit
Relay Circuit
AI Circuit
RTD Circuit
TC Circuit

ioLogik E1200 Series Introduction
1-2
Product Features
•Active communication with patented Active OPC Server
•2-port Ethernet switch for daisy-chain topologies
•Easy mass deployment and configuration with ioSearch™utility
•User-friendly configuration via web browser
•Save time and wiring costs with peer-to-peer communication
•User-defined Modbus/TCP addressing
•Simplify I/O management with MXIO library on either Windows or Linux platform
•Wide operating temperature: -40 to 75°C (-40 to 167°F)
•Supports SNMPv1/v2c
•UL/cUL Class I Division 2, ATEX Zone 2 certification
Inside the Box
The ioLogik E1200 is shipped with the following items:
•ioLogik E1200 remote Ethernet I/O server
•Document and software CD
•Quick installation guide
NOTE
Notify your sales representative if any of the above items are missing or damaged.

ioLogik E1200 Series Introduction
1-3
Product Model Information
Model
Description
ioLogik E1210
Remote Ethernet I/O with 2-port Ethernet switch and 16 DIs
ioLogik E1211
Remote Ethernet I/O with 2-port Ethernet switch and 16 DOs
ioLogik E1212
Remote Ethernet I/O with 2-port Ethernet switch, 8 DIs, and 8 DIOs
ioLogik E1213
Remote Ethernet I/O with 2-port Ethernet switch, 8 DIs, 4 DOs, and 4 DIOs (source
type)
ioLogik E1214
Remote Ethernet I/O with 2-port Ethernet switch, 6 DIs, and 6 relays
ioLogik E1240
Remote Ethernet I/O with 2-port Ethernet switch and 8 AIs
ioLogik E1241
Remote Ethernet I/O with 2-port Ethernet switch and 4 AOs
ioLogik E1242
Remote Ethernet I/O with 2-port Ethernet switch and 4 AIs, 4DIs, and 4DIOs
ioLogik E1260
Remote Ethernet I/O with 2-port Ethernet switch and 6 RTDs
ioLogik E1262
Remote Ethernet I/O with 2-port Ethernet switch and 8 TCs
ioLogik E1210-T
Ethernet remote I/O with 2-port Ethernet switch and 16 DIs, -40 to 75°C operating
temperature
ioLogik E1211-T
Ethernet remote I/O with 2-port Ethernet switch and 16 DOs, -40 to 75°C operating
temperature
ioLogik E1212-T
Ethernet remote I/O with 2-port Ethernet switch, 8 DIs, and 8 DIOs, -40 to 75°C
operating temperature
ioLogik E1213-T
Remote Ethernet I/O with 2 Port Ethernet switch, 8 DIs, 4 DOs, and 4 DIOs (source
type), -40 to 75°C operating temperature
ioLogik E1214-T
Ethernet remote I/O with 2-port Ethernet switch, 6 DIs, and 6 Relays, -40 to 75°C
operating temperature
ioLogik E1240-T
Ethernet remote I/O with 2-port Ethernet switch and 8 AIs, -40 to 75°C operating
temperature
ioLogik E1241-T
Ethernet remote I/O with 2-port Ethernet switch and 4 AOs , -40 to 75°C operating
temperature
ioLogik E1242-T
Ethernet remote I/O with 2-port Ethernet switch, 4 AIs, 4 DIs, and 4 DIOs, -40 to 75°C
operating temperature
ioLogik E1260-T
Ethernet remote I/O with 2-port Ethernet switch and 6 RTDs, -40 to 75°C operating
temperature
ioLogik E1262-T
Ethernet remote I/O with 2-port Ethernet switch and 8 TCs, -40 to 75°C operating
temperature

ioLogik E1200 Series Introduction
1-4
Product Specifications
Common Specifications
LAN
Ethernet: 2 x 10/100 Mbps switch ports, RJ45
Protection: 1.5 kV magnetic isolation
Protocols: Modbus/TCP, TCP/IP, UDP, DHCP, BOOTP, HTTP
Power Requirements
Power Input: 24 VDC nominal, 12 to 36 VDC
Physical Characteristics
Wiring: I/O cable max. 14 AWG
Dimensions: 27.8 x 124 x 84 mm (1.09 x 4.88 x 3.31 in)
Weight: under 200 g
Mounting: DIN rail or wall
Environmental Limits
Operating Temperature:
Standard Models: -10 to 60°C (14 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Storage Temperature: -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity: 5 to 95% (non-condensing)
Altitude: Up to 2000 m
Note: Please contact Moxa if you require products guaranteed to function properly at higher altitudes.
Standards and Certifications
Safety: UL 508
EMI:
EN 55022; EN 61000-3-2; EN 61000-3-3;
FCC Part 15, Subpart B, Class A
EMS:
EN 55024, EN 61000-4-2, EN 61000-4-3,
EN 61000-4-4, EN 61000-4-5, EN 61000-4-6,
EN 61000-4-8, EN 61000-4-11
Shock: IEC 60068-2-27
Freefall: IEC 60068-2-32
Vibration: IEC 60068-2-6
Green Product: RoHS, CRoHS, WEEE
Hazardous Location: UL/cUL Class I Division 2, ATEX Zone 2 (ioLogik E1214 pending)
Note: Please check Moxa's website for the most up-to-date certification status.
Warranty
Warranty Period: 5 years (excluding ioLogik E1214)
Details: See www.moxa.com/warranty
Note: Because of the limited lifetime of power relays, products that use this component are covered by a 2-year
warranty.

ioLogik E1200 Series Introduction
1-5
ioLogik E1210
Inputs and Outputs
Digital Inputs: 16 channels
Isolation: 3K VDC or 2K Vrms
Digital Input
Sensor Type: Wet Contact (NPN or PNP), Dry Contact
I/O Mode: DI or Event Counter
Dry Contact:
• On: short to GND
• Off: open
Wet Contact (DI to COM):
• On: 10 to 30 VDC
• Off: 0 to 3 VDC
Common Type: 8 points per COM
Counter Frequency: 250 Hz, power off storage
Digital Filtering Time Interval: Software selectable
Power Requirements
Power Consumption: 110 mA @ 24 VDC
MTBF (mean time between failures)
Time: 671,345 hrs
Database: Telcordia (Bellcore)
ioLogik E1211
Inputs and Outputs
Digital Outputs: 16 channels
Isolation: 3K VDC or 2K Vrms
Digital Output
Type: Sink
I/O Mode: DO or Pulse Output
Pulse Output Frequency: 500 Hz
Over-voltage Protection: 45 VDC
Over-current Protection: 2.6 A (4 channels @ 650 mA)
Over-temperature Shutdown: 175°C (typical), 150°C (min.)
Current Rating: 200 mA per channel
Power Requirements
Power Consumption: 208 mA @ 24 VDC
MTBF (mean time between failures)
Time: 923,027 hrs
Database: Telcordia (Bellcore)

ioLogik E1200 Series Introduction
1-6
ioLogik E1212
Inputs and Outputs
Digital Inputs: 8 channels
Configurable DIOs: 8 channels
Isolation: 3K VDC or 2K Vrms
Digital Input
Sensor Type: Wet Contact (NPN or PNP), Dry Contact
I/O Mode: DI or Event Counter
Dry Contact:
• On: short to GND
• Off: open
Wet Contact (DI to COM):
• On: 10 to 30 VDC
• Off: 0 to 3 VDC
Common Type: 8 points per COM
Counter Frequency: 250 Hz, power off storage
Digital Filtering Time Interval: Software selectable
Digital Output
Type: Sink
I/O Mode: DO or Pulse Output
Pulse Output Frequency: 500 Hz
Over-voltage Protection: 45 VDC
Over-current Protection: 2.6 A (4 channels @ 650 mA)
Over-temperature Shutdown: 175°C (typical), 150°C (min.)
Current Rating: 200 mA per channel
Power Requirements
Power Consumption: 155 mA @ 24 VDC
MTBF (mean time between failures)
Time: 561,930 hrs
Database: Telcordia (Bellcore)

ioLogik E1200 Series Introduction
1-7
ioLogik E1213
Inputs and Outputs
Digital Inputs: 8 channels
Digital Outputs: 4 channels
Digital Input/Output (configurable by jumper): 4 channels
Isolation: 3K VDC or 2K Vrms
Digital Input
Sensor Type: NPN, PNP, and dry contact
I/O Mode: DI or event counter
Dry Contact:
• On: short to GND
• Off: open
Wet Contact (DI to COM):
• On: 10 to 30 VDC
• Off: 0 to 3 VDC
Common Type: 12 points per COM
Counter/Frequency: 250 Hz, power off storage
Digital Output
I/O Mode: DO or Pulse Output
I/O Type: Source
Current: 500 mA per channel
Voltage: 15 to 30 VDC (12 or 9 VDC configurable by jumper on the 4 DO channels)
Pulse Wave Width/Frequency: 1 ms/500 Hz
Over-Voltage Protection: 45 VDC
Over-Current Limit: 1.5 A per channel @ 25°C
Over-Temperature Shutdown: 175°C (typical), 150°C (min.)
Output Current Rating: 0.5A per channel
Power Requirements
Power Input: 24 VDC nominal, 12 to 36 VDC
Power Consumption: 130 mA typical @ 24 VDC

ioLogik E1200 Series Introduction
1-8
ioLogik E1214
Inputs and Outputs
Digital Inputs: 6 channels
Relay Outputs: 6 channels
Isolation: 3K VDC or 2K Vrms
Digital Input
Sensor Type: Wet Contact (NPN or PNP), Dry Contact
I/O Mode: DI or Event Counter
Dry Contact:
• On: short to GND
• Off: open
Wet Contact (DI to COM):
• On: 10 to 30 VDC
• Off: 0 to 3 VDC
Common Type: 6 points per COM
Counter Frequency: 250 Hz, power off storage
Digital Filtering Time Interval: Software selectable
Relay Output
Type: Form A (N.O.) power relay
Contact Current Rating:
• Resistive Load: 5 A @ 30 VDC, 250 VAC, 110 VAC
Breakdown Voltage: 500 VAC
Relay On/Off Time: 1500 ms (max.)
Initial Insulation Resistance: 1000 M ohms (min.) @ 500 VDC
Mechanical Endurance: 5,000,000 operations
Electrical Endurance: 100,000 operations @ 5 A resistive load
Contact Resistance: 100 m ohms (max.)
Pulse Output: 0.3 Hz at rated load
Note: Ambient humidity must be non-condensing and remain between 5 and 95%. The relays of the ioLogik
E1214 may malfunction when operating in high condensation environments below 0° Celsius.
Power Requirements
Power Consumption: 188 mA @ 24 VDC
MTBF (mean time between failures)
Time: 808,744 hrs
Database: Telcordia (Bellcore)

ioLogik E1200 Series Introduction
1-9
ioLogik E1240
Inputs and Outputs
Analog Inputs: 8 channels
Isolation: 3K VDC or 2K Vrms
Analog Input
Type: Differential input
Resolution: 16 bits
I/O Mode: Voltage / Current
Input Range: 0 to 10 VDC, 0 to 20 mA, 4 to 20 mA
Accuracy:
± 0.1% FSR @ 25°C
± 0.3% FSR @ -10 and 60°C
± 0.5% FSR @ -40 and 75°C
Sampling Rate:
• All channels: 12 samples/sec
• Per channel: 1.5 samples/sec
• Only one channel enabled: 12 samples/sec
Input Impedance: 10M ohms (min.)
Built-in Resistor for Current Input: 120 ohms
Power Requirements
Power Consumption: 121 mA @ 24 VDC
MTBF (mean time between failures)
Time: 474,053 hrs
Database: Telcordia (Bellcore)
ioLogik E1241
Inputs and Outputs
Analog Outputs: 4 channels
Isolation: 3K VDC or 2K Vrms
Analog Output
Resolution: 12 bits
Output Range: 0 to 10 VDC, 4 to 20 mA
Voltage Output: 10 mA (max.)
Accuracy:
± 0.1% FSR @ 25°C
± 0.3% FSR @ -40 and 75°C
Load Resistor:
• Internal resistor: 400 ohms
Note: 24 V of external power required when loading greater than 1000 ohms.
Power Requirements
Power Consumption: 194 mA @ 24 VDC
MTBF (mean time between failures)
Time: 888,656 hrs
Database: Telcordia (Bellcore)

ioLogik E1200 Series Introduction
1-10
ioLogik E1242
Inputs and Outputs
Analog Inputs: 4 channels
Digital Inputs: 4 channels
Configurable DIOs: 4 channels
Isolation: 3K VDC or 2K Vrms
Analog Input
Type: Differential input
Resolution: 16 bits
I/O Mode: Voltage / Current
Input Range: 0 to 10 VDC, 0 to 20 mA, 4 to 20 mA
Accuracy:
± 0.1% FSR @ 25°C
± 0.3% FSR @ -10 and 60°C
± 0.5% FSR @ -40 and 75°C
Sampling Rate:
• All channels: 12 samples/sec
• Per channel: 3 samples/sec
• Only one channel enabled: 12 samples/sec
Input Impedance: 10M ohms (min.)
Built-in Resistor for Current Input: 120 ohms
Digital Input
Sensor Type: Wet Contact (NPN or PNP), Dry Contact
I/O Mode: DI or Event Counter
Dry Contact:
• On: short to GND
•Off: open
Wet Contact (DI to COM):
• On: 10 to 30 VDC
• Off: 0 to 3 VDC
Common Type: 4 points per COM
Counter Frequency: 250 Hz, power off storage
Digital Filtering Time Interval: Software selectable
Digital Output
Type: Sink
I/O Mode: DO or Pulse Output
Pulse Output Frequency: 500 Hz
Over-voltage Protection: 45 VDC
Over-current Protection: 2.6 A (4 channels @ 650 mA)
Over-temperature Shutdown: 175°C (typical), 150°C (min.)
Current Rating: 200 mA per channel
Power Requirements
Power Consumption: 139 mA @ 24 VDC
MTBF (mean time between failures)
Time: 502,210 hrs
Database: Telcordia (Bellcore)

ioLogik E1200 Series Introduction
1-11
ioLogik E1260
Inputs and Outputs
RTD Inputs: 6 channels
Isolation: 3K VDC or 2K Vrms
RTD Inputs
Input Type:
• PT50, PT100, PT200, PT500 (-200 to 850°C)
• PT1000 (-200 to 350°C)
• Resistance of 310, 620, 1250, and 2200 ohms
Sampling Rate:
• All channels: 12 samples/sec
• Per channel: 2 samples/sec
• Only one channel enabled: 12 samples/sec
Resolution: 0.1°C or 0.1 ohm
Accuracy:
± 0.1% FSR @ 25°C
± 0.3% FSR @ -40 and 75°C
Input Impedance: 625K ohms
Power Requirements
Power Consumption: 110 mA @ 24 VDC
MTBF (mean time between failures)
Time: 660,260 hrs
Database: Telcordia (Bellcore)
ioLogik E1262
Inputs and Outputs
Thermocouple Inputs: 8 channels
Isolation: 3K VDC or 2K Vrms
Thermocouple Input
Sensor Type: J (0 to 750°C), K (-200 to 1250°C), T (-200 to 350°C), E (-200 to 900°C), R (-50 to 1600°C),
S (-50 to 1760°C), B (600 to 1700°C), N (-200 to 1300°C)
Millivolt Type:
• Mode: ±78.126 mV, ±39.062 mV, ±19.532 mV
• Fault and over-voltage protection: -35 to +35 VDC (power off); -25 to +30 VDC (power on)
Sampling Rate:
• All channels: 12 samples/sec
• Per channel: 1.5 samples/sec
• Only one channel enabled: 12 samples/sec
Resolution: 16 bits
Accuracy:
± 0.1% FSR @ 25°C
± 0.3% FSR @ -40 and 75°C
Input Impedance: 10M ohms
Power Requirements
Power Consumption: 118 mA @ 24 VDC
MTBF (mean time between failures)
Time: 631,418 hrs
Database: Telcordia (Bellcore)

ioLogik E1200 Series Introduction
1-12
Physical Dimensions

ioLogik E1200 Series Introduction
1-13
Hardware Reference
Panel Guide
NOTE
The RESET button restarts the server and resets all settings to factory defaults. Use a pointed object such as
a straightened paper clip to hold down the RESET button for 5 seconds. The factory defaults will be loaded once
the READY LED turns green again. You may then release the RESET button.
Ethernet Port
Pin
1
2
3
4
Signal
TXD+
TXD-
RXD+
---
Pin
5
6
7
8
Signal
---
RXD-
---
---
LED Indicators
LED
State
Description
Power
Amber
System power is ON
OFF
System power is OFF
Ready
Green
System is ready
Flashing
Flashes every 1 second when the “Locate” function is triggered
Flashing
Flashes every 0.5 second when the firmware is being upgraded
Flashing
ON/OFF cycle period of 0.5 second represents “Safe Mode”
OFF
System is not ready
Port 1
Green
Ethernet connection enabled
Flashing
Transmitting or receiving data
Port 2
Green
Ethernet connection enabled
Flashing
Transmitting or receiving data
EXT
Green
EXT field power input is connected
Off
EXT field power input is disconnected

ioLogik E1200 Series Introduction
1-14
I/O Circuit Diagram
DI Circuit
Sinking DO Circuit

ioLogik E1200 Series Introduction
1-15
Sourcing DO Circuit

ioLogik E1200 Series Introduction
1-16
DIO Circuit