Moxa Technologies SDS-3008 Series User manual

P/N: 1802300800011
*1802300800011*
SDS-3008 Series
Quick Installation Guide
Moxa’s Industrial Smart Ethernet Switch
Edition 2.0, March 2017
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll
-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax:
1-714-528-6778
Moxa China (Shanghai office):
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe:
Tel:
[phone]
Fax:
[phone]
Moxa Asia-Pacific:
Tel:
[phone]
Fax:
[phone]
Moxa India:
Tel:
[phone]
Fax:
[phone]

2017 Moxa Inc. All rights reserved.

- 2 -
Overview
The SDS-3008 industrial smart Ethernet switch is the ideal device for IA
engineers and automation machine builders to make their networks
compatible with the vision of Industry 4.0. By breathing life into machines
and control cabinets, the smart switch simplifies daily tasks with its easy
configuration and easy installation. In addition, it is monitorable and easy
to maintain throughout the entire product life cycle.
The most frequently used automation protocols—including EtherNet/IP,
PROFINET, and Modbus/TCP—are embedded in the SDS-3008 to provide
enhanced operational performance and flexibility by making it
controllable and visible from automation HMIs. It also supports a range of
useful management functions, including IEEE 802.1Q VLAN, port
mirroring, SNMP, and warning by relay.
Package Checklist
The SDS-3008 is shipped with the following items. If any of these items
are missing or damaged, please contact your customer service
representative for assistance.
•1 SDS-3008 industrial smart Ethernet switch
•Protective caps for unused ports
•Quick installation guide (printed)
•Warranty card
Features
•8 10/100BaseT(X) Fast Ethernet ports
•Web-based graphical user interface for quick configuration and
management
•Supports EtherNet/IP, PROFINET, and Modbus/TCP industrial
protocol profiles for easy device integration and monitoring in
HMI/SCADA systems
•Supports IEEE 802.1D-2004 and IEEE 802.1w STP/RSTP for rapid
network redundancy
•IEEE 802.1Q VLAN to ease network planning
•Unused port lock, SNMPv3 and HTTPS to enhance network security
•Role-based account management for self-defined administration
and/or user accounts
•ABC-02 automatic backup configurator for quick event log and
configuration backup. Can also enable quick device change over and
firmware upgrade
•Automatic warning by exception through relay output
•Local log and the ability to export inventory files simplify inventory
management
Default Settings
•Default IP address: 192.168.127.253
•Default Subnet Mask: 255.255.255.0
•Default Usernames: admin, user
•Default Password: moxa

- 3 -
SDS-3008 Panel Layout
1. 1 to 8 10/100BaseT(X) ports (bottom to top)
2. System status LEDs (top to bottom)
STATE LED indicator (Green), FAULT LED indicator (Red),
PWR1 LED indicator (Amber), PWR2 LED indicator (Amber)
3. 1 to 8 port status LEDs (bottom to top)
•LED lights in Green: 100 Mbps
•LED lights in Amber: 10 Mbps
4. Model side label (Multiple production information included)
•Default IP: 192.168.127.253
5. Model name
6. Latch of the DIN-rail mounting kit
7. Grounding screw (chassis ground)
8. 4-pin terminals for power inputs (P1/P2), relay output (R) and
digital input (DI)
NOTE: starting from the front side called first terminal
9. Reset button
10.
USB storage port (type A connector)
11.
DIN-rail mounting kit
12.
Screw hole (reserved for other DIN-rail mounting methods;
for more
information please see the DIN-Rail Mounting section)

- 4 -
Mounting Dimensions; unit = mm (inches)
DIN-Rail Mounting
There are 2 options for DIN-rail mounting that can be adopted on a
SDS-3008. Option 1 is the default type when shipped.
Option 1 (Default):
When shipped, the metal DIN-rail mounting kit is fixed to the back panel
of the SDS-3008. Mount the SDS-3008 on the corrosion-free mounting
rail that adheres to the EN 60715 standard.
Suggested Installation Method
STEP 1—Insert the upper lip of
the DIN
-rail kit into the
mounting rail.
STEP 2
—Press the SDS-3008
towards the mounting rail until it
snaps into place.

- 5 -
Suggested Removal Method
STEP 1—Pull down the latch on
the DIN
-rail kit with a
screwdriver.
STEP
S 2 & 3—Slightly pull the
SDS
-3008
forward and lift up to
remove it from the mounting
rail.
Option 2 (when side cabling is needed):
The metal DIN-rail mounting kit can be fixed to the side panel (mold side)
of the SDS-3008 (horizontal or vertical). Mount the SDS-3008 on the
corrosion-free mounting rail that adheres to the EN 60715 standard.
Suggested Installation Method
STEP 1—Detach the metal DIN-rail mounting kit from the back panel and
attach it to the side panel (mold side) in either the horizontal or vertical
direction as indicated in the figure below.

- 6 -
STEP 2—Insert the upper lip of the
DIN
-rail kit into the mounting rail.
STEP 3
—Press the SDS-3008 towards
the mounting rail until it snaps into
place.
Suggested Removal Method
STEP 1—
Pull down the latch on the
DIN
-rail kit with a screwdriver.
STEP
S 2 & 3—Slightly pull the
SDS
-3008 forward and lift up to
remove it from the mounting rail.
NOTE
Screws that are used to fix the DIN-rail kit on the SDS-3008
should be
securely fastened before mounting on the mounting
rail. Please make sure
that if you remove the DIN-rail
, it must be
securely fastened when it is reattached.
ATTENTION
In order to
ensure reliable operations, please make sure the
operating temp. of the environment
does not exceed the spec.
When
mounting a SDS-3008 with other operating units in a
cabinet without forced ventilation,
minimum spacing of 3cm on
both sides and above/below the switch is recommended.
Wiring Requirements
ATTENTION
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your Moxa
Industrial Smart Ethernet Switch.
Calculate the
maximum possible current in each power wire and common wire.
Observe all electrical codes dictating the maximum current
allowable for each wire size.
If the current goes above the
maximum ratings, the wiring could overheat, causing serious
damage to your equipment.

- 7 -
Be sure to read and follow these important guidelines:
•Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
NOTE
Do not run signal or communications wiring and power wiring
through the same wire conduit. To avoid interference, wires with
different signal characteristics should be routed separately.
•You can use the type of signal transmitted through a wire to
determine which wires should be kept separate. The rule of thumb is
that wiring that shares similar electrical characteristics can be
bundled together.
•You should separate input wiring from output wiring.
•We advise that you label the wiring to all devices in the system.
Grounding the Industrial Smart Ethernet Switch
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw (chassis ground) to the grounding surface prior to
connecting devices.
ATTENTION
This product is intended to be mounted onto a well
-grounded
mounting surface, such as a metal panel.
Suggested Wire Type for Wiring Relay Contact (R),
Digital Input (DI) and Power Inputs (P1/P2)
The switch includes two 4-pins 3.5mm pin-pitch terminal blocks. When
wiring the relay contact (R), digital input (DI) and power inputs (P1/P2)
for the SDS-3008, we suggest using the cable type - AWG (American Wire
Gauge) 18-24 and the corresponding pin type cable terminals.
NOTE
The wire must be able to withstand at least 105℃and the torque
value should be 4.5 lb-in (0.51 N-m).

- 8 -
NOTE
We suggest the length of the pin type cable terminal is 8 mm.
I
n order to tighten the wire properly,
①
use a small flathead
screwdriver to press the push
-in button beside
each terminal of
the terminal block connector before and during
②
inserting the
wire.
③Release the screwdriver after the wire has been fully
inse
rted. Please refer to the diagram below.
Wiring the Relay Contact
The SDS-3008 has one relay output for identifying when a specific event
has occurred (i.e., fault; see below). This relay output uses the first two
contacts out of the first 4-pin terminal on the SDS-3008's top panel.
Refer to the instructions and diagram below on how to connect the wires
to the terminal block connector, and how to attach the terminal block
connector to the terminal block receptor.
STEP 1—Insert two wires into the relay position (see the diagram below
showing the top view) on the terminal to form an open circuit.
STEP 2—To keep the relay wires from coming loose, use a small flathead
screwdriver to press the button beside each terminal of the plastic
terminal block connector in order to insert the wire tightly. Release the
screwdriver after the wire has been inserted properly.
STEP 3—Insert the plastic terminal block connector prongs into the
terminal block receptor, which is located on the SDS-3008's top panel.
FAULT:
The two relay contacts of the 4-pin terminal block connector can be used
to indicate that a user-configured event has occurred. The two wires
attached to the relay contacts will form an open circuit when a
user-configured event is triggered. If a user-configured event does not
occur, the circuit remains closed as the relay itself is closed. Examples of
user-configured events include port link-down and power input ON/OFF.
For more details about user-configured events, please refer to the
SDS-3008 user manual.

- 9 -
NOTE
The relay output of the SDS-3008 reflects a potential-free,
normally opened solid
-state relay. Therefore, not only when
user
-configured events are triggered but also when there is no
power supply to the switch
it will open. To indicate a fault has
occurred
one
can integrate the relay contact on the smart switch
with an external alarming system circuit so that the status of
user
-configured events or no power supply can be monitored.
An
example is given in the diagram below w
here the buzzer will
sound when
user-configured events happen.
Wiring the Digital Input
The SDS-3008 has one set of digital inputs (DI). The DI consist of two
contacts of the second 4-pin terminal block on the SDS-3008’s top panel,
and the other 2 contacts are used for the power 2 (P2) DC inputs.
Refer to the instructions and diagram (top view) below on how to connect
the wires to the terminal block connector, and how to attach the terminal
block connector to the terminal block receptor.
STEP 1: Insert the negative (ground)/positive DI wires into the
respective ┴/I terminals.
STEP 2: To prevent the DI wires from coming loose, use a small flathead
screwdriver to press the button beside each terminal of the plastic
terminal block connector in order to insert the wire tightly. Release the
screwdriver after the wire has been properly inserted.
STEP 3: Insert the plastic terminal block connector prongs into the
terminal block receptor, which is located on the top panel of the
SDS-3008.

- 10 -
Wiring the Redundant Power Inputs (12/24/48
VDC)
The SDS-3008 has two sets of power inputs–power input 1 (PWR 1/P1)
and power input 2 (PWR 2/P2). The top view of the terminal block
connector and the positions of the power inputs are shown below.
Take the following steps to wire the redundant power inputs:
STEP 1: Insert the Positive/Negative DC wires into the V1+/V1- terminal
for PWR 1 and/or V2+/V2- terminal for PWR 2.
STEP 2: To prevent the DC wires from coming loose, use a small flathead
screwdriver to press the button beside each terminal of the plastic
terminal block connector in order to insert the wire tightly. Release the
screwdriver after the wire has been properly inserted.
STEP 3: Insert the plastic terminal block connector prongs into the
terminal block receptor, which is located on the top panel of the
SDS-3008.
ATTENTION
Before connecting the SDS
-
3008 to the DC power inputs, ensure
the DC power supply voltage is stable and of a correct level and
polarity.
Communication Connections
Each SDS-3008 smart Ethernet switch has 2 types of communication
ports:
•1 USB storage port (type A connector)
•8 10/100BaseT(X) Fast Ethernet ports
USB Storage Connection
The SDS-3008 has one USB storage port (type A connector; see the
diagram below for pinout assignments) on the front panel. Use Moxa’s
ABC-02-USB automatic backup configurator to connect to the
SDS-3008's USB storage port in order to perform configuration backup,
firmware upgrade, or system log file backup.
USB Storage Port (Type A Connector) Pinouts
Pin
Description
1
VCC (+5V)
2
D– (Data -)
3
D+ (Data+)
4
GND (Ground)