Moxa Technologies IKS-6324 Series Manual

— 1 — — 2 — — 3 —
Industrial Rackmount Switch
IKS-6324 Series
Hardware Installation Guide
Second Edition, June 2008
Package Checklist
The Moxa IKS-6324 Series industrial rackmount switches are shipped
with the following items. If any of these items is missing or damaged,
please contact your customer service representative for assistance.
y1 Moxa IKS-6324 Switch
yHardware Installation Guide
yMoxa Product Warranty Statement
yProtective caps for unused ports
y2 rack-mount ears
Panel Layouts
2468
1357
10 12 14 16
911 13 15
18 20 22
17 19 21
12
IRK-6324
TX RX TX RX
M1
LNK/ACT SPEED
FAULT
STAT PWR1 PWR2
MODE
FDX/HDX
19 1
20 218 22
17 21
8
7
6
5
2
1
4
3
16
15
14
13
10
9
12
11
M1
IRK-6324
1543
68
2
7
Front View
Rear View
1. LED Indicators (System status, Interface Module mode, Interface
Module port)
2. Push-button switch to select mode for Interface Module
3. Model Name
4. Fast Ethernet / Gigabit Ethernet Interface Modules
5. 10/100BaseT(X) port
6. 10-pin terminal block for power inputs
7. Rack Mounting Kit
8. Ground Screw
Dimensions (unit = mm)
254
44
278.3
440
44
31.8
480
462.6
292.4
Side View Side View
Front View
Rear View
Top View
Fast Ethernet Interface Module
40.7 40.7
40.7 40.7
86.6 86.6
86.6
86.6
PM-7200-1MSC/ PM-7200-1SSC PM-7200-1MST
PM-7200- 2MSTPM-7200-2MSC/PM-7200-2SSC
Gigabit Ethernet Interface Module
PM-7200-2GTXSFP
86.6
40.7
Slot 1 for 2-port PM-7200 Gigabit
Ethernet combo module, or 2- or 1-port
PM-7200 fast Ethernet modules.
Rack Mounting
Use four screws to attach the switch to a standard rack.
Wiring Requirements
WARNING
Safety First!
Be sure to disconnect the power cord before installing
and/or wiring your Moxa industrial rackmount switch.
Calculate the maximum possible current in each power
wire and common wire. Observe all electrical codes
dictating the maximum current allowable for each wire
size. If the current goes above the maximum ratings, the
wiring could overheat, causing serious damage to your
equipment.
Grounding Moxa’s Rackmount Switches
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw to the grounding surface prior to connecting devices.
ATTENTION
This product is intended to be mounted to a well-grounded
mounting surface, such as a metal panel.
Wiring the Power Inputs
The IKS series supports dual redundant power supplies, named “Power
Supply 1 (PWR1)” and “Power Supply 2 (PWR2)”. The connections for
PWR1 and PWR2 are located on the terminal block. Front view of the
terminal block connectors are shown here.
P/N: 1802063240011

— 4 — — 5 — — 6 —
Wiring the Redundant Power Inputs
The IKS-6324 switch has two sets of power input—power input 1 and
power input 2.
STEP 1: Insert the dual set positive/negative DC wires into PWR1
and PWR2 terminals (+ Æpins 1, 9, - Æpins 2, 10). Or insert the L/N
AC wires into the PWR1 terminals (L Æpin 1, N Æpin 2).
STEP 2: To keep the DC or AC wires from pulling loose, use a
screwdriver to tighten the wire-clamp screws on the front of the
terminal block connector.
LED Indicators
The front panel of the IKS-6324
switch contains several LED
indicators. The function of each
LED is described in the table below.
LED Color State Description
System LEDs
On System has passed self-diagnosis
test on boot-up and is ready to run.
GREEN
Blinking System is undergoing the
self-diagnosis test.
STAT
RED On
System failed self-diagnosis on
boot-up.
On Power is being supplied to the main
module’s power input PWR1.
PWR1 AMBER
Off Power is not being supplied to the
main module’s power input PWR1.
On Power is being supplied to the main
module’s power input PWR2.
PWR2 AMBER
Off Power is not being supplied to the
main module’s power input PWR2.
On System initiation has failed.
FAULT RED Off System initiation was successful.
Note: Use the Mode push-button switch to cycle among the LNK/ACT,
SPEED, and FDX/HDX LEDs. The status of these three settings is
indicated by the LEDs for the various ports. The system will switch to
LNK/ACT automatically after 5 seconds.
Mode LEDs
On The corresponding module port’s
link is active.
Blinking The corresponding module port’s
data is being transmitted.
LNK/ACT GREEN
Off The corresponding module port’s
link is inactive.
Off
The corresponding module port’s
data is being transmitted at 10
Mbps.
On
The corresponding module port’s
data is being transmitted at 100
Mbps.
SPEED GREEN
Blinking
The corresponding module port’s
data is being transmitted at
1000 Mbps.
On
The corresponding module port’s
data is being transmitted at full
duplex.
FDX/HDX GREEN
Off
The corresponding module port’s
data is being transmitted at half
duplex mode.
* Slot 1 (M1) is mainly used for Gigabit modules. If 100BaseFX modules
are used in Slot 1 (M1), the modules will not support “Far End Fault”.
The Link/ACT LED indicator will stay at “Green (ON)” status when
Fiber TX cable is unplugged.
Specifications
Technology
Standards IEEE802.3, 802.3u, 802.3ab, 802.3z, 802.3x
Flow Control IEEE802.3x flow control, back pressure flow
control
Interface
Fast Ethernet 10/100BaseT(X) or 100BaseFX (SC/ST
connector)
Gigabit Ethernet 10/100/1000BaseT(X),
1000BaseSX/LX/LHX/ZX (SFP slot, LC
connector)
System LED
Indicators STAT, PWR1, PWR2, FAULT
Module LED
Indicators LNK/ACT, FDX/HDX, SPEED
Optical Fiber (100BaseFX)
Distance Multi mode
0 to 5 km, 1300 nm (50/125μm, 800 MHz*km)
0 to 4 km, 1300 nm (62.5/125μm, 500 MHz*km)
Single mode
0 to 40 km, 1310 nm (9/125μm, 3.5 PS/(nm*km))
Min. TX Output Multi mode: -20 dBm; Single mode: -5 dbm
Max. TX Output Multi mode: -10 dBm; Single mode: 0 dbm
RX Sensitivity -36 to -32 dBm (Single), -34 to -30 dBm (Multi)
Power
Input Voltage Low Voltage: 24/48 VDC (9 to 60 V)
High Voltage: 110/250 VDC (88 to 300 V)
and 100/240 VAC (85 to 264 V)
Input Current Max. 0.68A @ 24 VDC
Max. 0.35A @ 48 VDC
Max. 0.17/0.11A @ 110/220 VDC
Max. 0.33/0.23A @ 110/220 VAC
Connection 10-pin Terminal Block
Overload Current
Protection 6.3 A
Reverse Polarity
Protection Present
Mechanical
Casing IP 30 protection, metal case
Dimensions
(W x H x D) 440 x 44 x 254 mm (17.32 x 1.73 x 10.00 in.)
Weight 4300g
Installation 19-inch Rack Mounting
Environmental
Operating Temp. -40 to 75°C (-40 to 167°F) for -T models
Storage Temp. -40 to 85°C (-40 to 185°F)
Ambient Relative
Humidity 5 to 95% (non-condensing)
Regulatory Approvals
Safety: EN60950-1 (Pending)
Maritime: ABS/BV/CCS/DNV/GL/KR/LR/NKK/PR/RINA
(Pending)
Road Traffic: NEMA TS2 (Pending)
EMI: FCC Part 15, CISPR (EN55022) class A
Railway EN50121-4 (Pending)
Shock & Vibration EN50155 (EN/IEC 61373, Category 1, Class B)
Warranty 5 years
Click here for online support:
www.moxa.com/support
The Americas: [phone] (toll-free: 1-888-669-2872)
Europe: [phone]
Asia-Pacific: [phone]
China: [phone] (toll-free: 800-820-5036)
©2008 Moxa Inc., all rights reserved.
Reproduction without permission is prohibited.