Moxa Technologies EDS-2005-EL Series User manual

P/ N : 1 8 0 2 0 2 0 0 0 3 0 2 0
*1802020003020*
ED S-2 0 0 5 - EL/ ELP Series
Quick I nst a lla t ion Guide
M ox a Et h e r D evice Sw it ch
Version 1 .0, O ct ob er 2 0 1 9
Te chnica l Su ppor t Con t a ct I nfor m at ion
w w w .m ox a.com / supp or t
Moxa Am er icas:
Toll
-free: 1 - 888-669-2872
Tel:
1- 714-528-6777
Fax:
1- 714-528-6778
Mox a China ( Sh an ghai office) :
Toll
-free: 800-820-5036
Tel:
+ 86-21-5258-9955
Fax:
+ 86-21-5258-5505
Moxa Europe:
Tel:
+ 49-89-3 70 03 99- 0
Fax:
+ 49-89-3 70 03 99-99
Moxa Asia-Pacific:
Tel:
+ 886- 2 - 8919-1230
Fax:
+ 886- 2 - 8919-1231
Moxa I ndia:
Tel:
+ 91-80-4172-9088
Fax:
+ 91-80-4132-1045

2019 Moxa I nc. All rights r eserved.

- 2 -
Ove r vie w
The EDS-2005-EL/ ELP Series has a 5- port com binat ion t o sim plif y
netw ork expansion. There ar e t wo housing t ypes available for t he user
t o select depending on t he requirem ent s of t heir applicat ion . The ELP
has a plastic housing and t he EL has a m et al housing. The com pact
switches provide a cost - effective solution for your industrial Ethernet
connect ion r equir em ent s.
The EDS-2005-EL/ ELP Series provides 12/ 24/ 48 VDC (9.6 t o 60 VDC)
power input, and the switches are available w it h a standard oper ating
t em peratur e r ange from -10 to 60° C. The switches are r ugged enough
to operate reliably in harsh industrial environm ents.
To pr ovide greater versatility for use with applicat ions from different
indust ries, t he EDS-2005-EL/ ELP Series also allows users t o enable or
disable broadcast storm pr otection ( BSP) , Qualit y of Serv ice ( QoS)
function via t he DI P swit ches on t he t op panel.
The EDS-2005-EL/ ELP swit ches can be easily installed wit h DI N- r ail
m oun ting as w ell as dist ribut ion box es. The DI N- rail m o unt in g
capability and I P40 housing wit h LED indicators ensure t hat t he p lu g-
and-play EDS-2005-EL/ ELP swit ches are reliable and easy t o use.
N OTE
Throughout this Quick I n st allat ion Gu ide, w e use ED S as an
abbreviat ion for Moxa EtherDevice Switch:
ED S = Mox a Et herDevice Sw itch
ATTEN TI ON
This device com plies w ith part 15 of FCC Rules. Operation is
su bj ect
t o t h e f ollowing t w o con di tions: ( 1 ) Th is device m ay n ot
cause harm f ul int er ference, and ( 2) t h is device m u st accept
any int er ference r eceived, including int er ference t hat m ay
cause undesired oper ations.
Pa cka ge Che cklist
Your EDS is shipped w it h t he following it em s. I f any of t hese it em s are
m issing or dam aged, please contact your custom er service
representative for assistance.
• Moxa EtherDevice™ Switch
• Quick inst allation guide (printed)
• War ranty card

- 3 -
Featur e s
H igh Pe rf or m a n ce N e t w or k Sw it ch in g T e ch nolog y
• 10 / 1 00BaseT( X) aut o-n egotiat ion sp eed, full/ half duplex m ode,
auto MDI / MDI -X connection.
• I EEE 802 .3 for 10 BaseT, I EEE 802.3u for 100 BaseT( X) .
• I EEE 8 02. 1p f or Quali t y of Ser vice ( QoS) t r affic prioritized funct ion.
• St or e- and-forward switching process t ype.
I n du st r ia l- grade Reliabilit y
• Broadcast storm protection t o prevent network devices from
crashing
Rugge d D e sign
• Operating t em per at ure range fr om -10 t o 60° C
• I P40, rugged high-st r ength case
• DI N-r ail or panel m ount ing abilit y
W ARN I N G
The
power for t his product is int ended t o be supplied by a
List ed Power Supply, with out put m ark ed LPS, and r at ed t o
deliv er 12 t o 48 VDC at a m axim um
of 0.11 A.
The DC
j ack should be used with an LPS unit that is rated t o
deliv er 12 t o 48 VDC at a m inim um of
1.1 A. The product
sh ould not be disassem bled b y operator s or serv ice p eople.

- 4 -
Pane l Layout of ED S-2 0 0 5 - EL/ EDS-2005- ELP
1. Chassis ground screw
2. Term inal block for power input
3. DI P sw it ch
4. Power LED
5. 1 0/ 1 00 BaseT( X) Por t
6. 1 0/ 1 00 BaseT( X) Por t LED
7. Port num ber
8. Model nam e

- 5 -
Mount ing Dim e nsions
ED S-2 0 0 5 - EL Series
ED S-2 0 0 5 -ELP Se r ie s

- 6 -
D I N - ra il M o un t in g
When shipped, t he DI N- rail m ount ing k it is fixed t o t he back panel of
the EDS. Mount t he EDS on t he cor rosion- free m ount ing r ail t hat
adher es to the EN 60715 standard.
Sug ge st e d I n sta lla t ion M e t h od
STEP 1 :
I nser t t he u pp er lip of t he DI N
-
rail k it int o t he m ount ing r ail.
S
TEP 2 :
Press t he device t owards t he
m ounting r ail u ntil
it snaps int o
place.
Alt ernatively, you can use
a screwdriver t o attach t o the
bot tom of t he DI N
-
rail kit and pull
down.
Sug ge st e d R em o va l M e t h od
STEP 1 :
Pull down t he latch on t he DI N
-
r ai l k it w it h a scr ew dr iver.
STEP 2 :
Slightly pull t he device
forward
and lift up t o rem ove it from t he
m ounting r ail.
N OTE
1. I f t he equipm en t is used in a m anner not specif ied b y t he
m anufactu rer , t he pr ot ection provided by the equipm ent
m ay be im paired.
2.
The inst allation and t he safety of any syst em incorporating
t he equipm ent is t he r esponsibility of t he assem bler of t he
sy st em .
3.
This is an OPEN TYPE m odule and should be installed in a
safety enclosure w it h m echanical rigidit y and an
appropriat e I P r at ing.

- 7 -
W a ll M ou n t in g ( op t ion a l)
For som e applicat ions, you will find it convenient t o m ount EDS on the
wall, as illust r ated below.
There are tw o options for installation: The first option
is to h
ook t he EDS DI N- rail lat ch on t he openin g of
the
w all m oun t k it ( see p ict ure above) and t h en
m ount the w all
-m ount kit on the wall wit h screw s.
( The ot her opt ion is t o perform t h ese t w o st eps in
the other order.)
The heads of t he screws should be
less than
6.0 m m in diam et er, and t he sh aft s shou ld be less t han 3.5 m m in
diam eter, as shown in t he figure at the right.
N OTE
Before t igh tening screws int o t he w all, m ake sur e t he screw
head and shank size are suit able by inserting t h
e screw into
one of the keyhole
-shaped apert ures of t he Wall Mount ing
Plat es.
Do not screw the screws in all t h e w ay —leave about 2 m m t o allow
room for sliding t he w all m ount panel betw een t he w all an d t he screw s.
Once t he screws are fixed in t he
wall, insert the
two screw heads
through the large part s of the
keyhole
-shaped aper t ures, and
then slide EDS downw ards
, as
indicat ed. Tight en the
t w o
screws for added st abilit y.
W ARN I N G
Extern al m et al part s are hot . Take necessary pr ecaut ions if it is
necessary t o t ouch.

- 8 -
W ir in g Re q uir e m e nt s
W ARN I N G
Do not disconnect m odules or w ires
unless t he power supply
has been swit ched off or t he area is known t o be non
-
hazardous.
The devices m ay only be conn ect ed t o t he supply
voltage show n on t he t ype plate.
The devices are designed for operation with a
Safet y Ext ra- L
ow
V
oltage. Thus, they m ay only be connected t o t he supply
voltage connections and t o t he signal cont act with t he
Safet y
E
xt r a- Low Volt ages ( SELV) in com plian ce w it h I EC950/
EN60950/ VDE0805.
W ARN I N G
Sa fe t y Fi r st !
Be sure t o disconnect the power cord before inst alling and/ or
wiring y our
Moxa EtherDevice Switch.
Calculat e t he m axim um possible curr ent in each pow er wire
and com m on w ir e. Observe all elect r ical codes dict ating t he
m axim um cur rent allow able for each w ire
size.
I f t he current goes abov e t he m axim um r at ings, t he w iring
could over heat , causing serious dam age t o y ou r eq uipm ent .
You should also pay at tention t o the following item s:
• Use separ at e paths t o r oute w iring for power and devices. I f power
wiring an d device w ir ing pat hs m ust cross, m ake sure t he wires are
perpendicular at t he intersection point.
N OTE: Do not run sign al or com m unicat ions wir in g and p ow er
wiring in t he sam e wire conduit . To avoid int erference, wires wit h
differ ent signal characteristics should be rout ed separately.
• You can u se t he t ype of signal t r ansm it t ed t hr ough a w ir e t o
determ ine w hich w ires sh ould be k ept separ ate. The r ule of t hum b
is t hat w iring t hat shares sim ilar elect rical ch ar acterist ics can be
bu ndled t o get h er .
• Keep input wiring and output wiring separated.
• I t is strongly advised that you label wiring to all devices in t he
syst em when necessary.

- 9 -
Gr ou ndin g M ox a Et he r D ev ice Sw it ch
Grounding and w ire r out ing h elp lim it th e effect s of n oise due t o
elect rom agn et ic interference ( EMI ) . Run t he g round con nection f rom
the ground screw t o the grounding surface prior t o connecting devices.
A 4 m m 2conductor m ust be used when a connection to the ext ernal
grounding screw is utilized.
ATTEN TI ON
This
product is int ended to be m ounted t o a well- grounded
m ounting surface, such as a m etal panel.
W iring t he Pow er I nput
The t op t w o contacts and t he bot t om t wo contacts of t he 2 or 3 contact
t er m inal block connect or on t he EDS’s t op panel are used for t h e EDS’s
two DC input s. Top and front v iew s of one of t he term inal block
connectors are shown here.
STEP 1 :
I nsert t he negat ive/ posit iv e DC wires int o t he V- / V+ t er m in al s.
STEP 2 :
To k eep t he DC wires from pulling loose, u se a sm all flat -blade
screw driver to t ight en t he wire-clam p screws on the fr ont of t he
t er m inal block connect or.
STEP 3 :
I nser t t he plast ic t erm inal block con nector pr ongs int o t he t erm inal
block receptor, which is locat ed on the EDS’s t op panel.
N OTE
The p ow er source com es fr om secondary circuit s. Th ese cir cuits
are separated from m ains circuit s by a t ransform er in w hich the
prim ary w in dings are separated fr om t he secondary w indings
by reinforced inst allation, double inst allation, or a screen
connected t o t he prot ect ive conductor t erm inal.
ATTEN TI ON
Before connect ing
the EDS t o t he DC power input s, m ake sur e
the DC power source voltage is stable.

- 10 -
ATTEN TI ON
One individual conductor in a clam ping poin t w it h 28
-14 AWG
wire size, and a t orque value of 1.7 lb-in should be used.
Com m un icat ion Conne ct ions
The EDS-2005-EL/ ELP m odels have 1 0/ 1 00BaseT( X) Et her net p or t s.
1 0 / 1 0 0 Ba se T( X) Et he r ne t Por t Conn ect ion
The 10/ 100BaseT( X) port s located on t he EDS’s front panel are used t o
conn ect t o Et hernet - enabled devices.
Below we show pinouts for bot h MDI ( NI C-t ype) port s and MDI -X
( HUB/ Sw it ch -type) port s, and also show cable wiring diagram s for
st r aight-t hrough and cross-over Ethernet cables.
1 0 / 1 0 0 Base T( x) RJ4 5 Pinout s
M D I Por t Pino ut s
MDI -X P or t Pin ou t s
8 - pin RJ4 5
Pin
Signa l
1
Tx+
2
Tx-
3
Rx+
6
Rx-
Pin
Signa l
1
Rx+
2
Rx-
3
Tx+
6
Tx-
RJ4 5 ( 8 -pin) t o RJ4 5 ( 8 -pin ) St ra ig ht - t h r ou gh Ca ble W irin g
RJ4 5 ( 8 -p in) t o RJ4 5 ( 8 -pin) Cr oss- ove r Cable W ir ing