Moxa Technologies ToughNet TN-5510A-2GLSX-ODC Manual

2015 Moxa Inc. All rights reserved.
Reproduction without permission is prohibited.
P/N: 1802055100061
*1802055100061*
TN-5510A-2GLSX-ODC and
TN-5510A-8POE-2GLSX-ODC
Hardware Installation Guide
Moxa ToughNet Switch
Second Edition, March 2015
www.ipc2u.ru
www.moxa.pro

- 2 -
Overview
The ToughNet TN-5510A-2GLSX-ODC and TN-5510A-8POE-2GLSX-ODC
series M12 managed Ethernet switches are designed for industrial
applications in harsh environments. The TN series switches use M12
connectors to ensure tight, robust connections, and guarantee reliable
operation against environmental disturbances, such as vibration and
shock. The wide 24 to 110 VDC range with dual power inputs (non-PoE
series) increases the reliability of your communications.
The TN-5510A-2GLSX-ODC and TN-5510A-8PoE-2GLSX-ODC switches
provide up to 8 Fast Ethernet M12 ports, and 2 ports on the down side to
provide the Gigabit fiber interface with an embedded 2 km multimode
fiber transceiver. Moreover, the -40 to 75°C operating temperature and
IP54-rated waterproof enclosure allow deployment in harsh
environments. The TN-5510A Ethernet switch is compliant with the
essential sections of EN 50155 (railway applications), making it suitable
for a variety of industrial applications.
Package Checklist
The ToughNet TN-5510A-2GLSX-ODC and TN-5510A-8POE-2GLSX-ODC
switches are shipped with the following items. If any of these items are
missing or damaged, please contact your customer service
representative for assistance.
•1 Moxa ToughNet switch
•M12 to DB9 console port cable
•2 protective caps for console and relay output ports
•Panel mounting screws
•CD-ROM with user’s manual
•Hardware installation guide
•Warranty card
Features
Anti-Vibration Circular Connectors for Robust Links
•M12 D-coding 4-pin female connectors for Fast Ethernet
10/100BaseT(X) ports
•Fiber-optic ODC connectors with embedded 2 km Gigabit Ethernet
1000BaseLSX
•M12 A-coding 5-pin male connectors for console and relay output
•M23 6-pin male connector for power input
Dual Power Inputs
•Supports 24-110 VDC (16.8 to 137.5 VDC)
High Performance Network Switching Technology
•IEEE 1588 PTP (Precision Time Protocol) for precise time
synchronization of networks
•DHCP Option 82 for IP address assignment with different policies
•EtherNet/IP and Modbus/TCP industrial Ethernet protocols supported
•Turbo Ring and Turbo Chain (recovery time <20 ms @250 switches),
and STP/RSTP/MSTP for network redundancy
•IGMP Snooping and GMRP for filtering multicast traffic from industrial
Ethernet protocols
•Port-based VLAN, IEEE802.1Q VLAN, and GVRP protocol to ease
network planning
www.ipc2u.ru
www.moxa.pro

- 3 -
•QoS (IEEE 802.1p/1Q and ToS/DiffServ) allows real-time traffic
classification and prioritization
•802.3ad, LACP for optimum bandwidth utilization
•TACACS+, SNMPv3, IEEE 802.1X, HTTPS, and SSH to enhance
network security
•SNMP v1/v2c/v3 for different levels of network management
•RMON for efficient network monitoring and proactive capability
•Bandwidth management prevents unpredictable network status
•Lock port allows access by only authorized MAC addresses
•Port mirroring for online debugging
•Automatic warning by exception through email, relay output
•Automatic recovery of connected device’s IP addresses
•Line-swap fast recovery
•LLDP for automatic topology discovery in network management
software
•Loop protection prevents network loops
•Configurable through Web browser, Telnet/serial console, CLI, and
Windows utility
Designed for Industrial-Specific Applications
•Two Gigabit fiber ports to meet high EMI immunity, long-distance,
and bandwidth requirements
•Essential compliance with EN 50155
•-40 to 75°C operating temperature range
•IP54, rugged high-strength case
•Panel mounting or DIN rail mounting installation capability
Recommended Optional Accessories
•CBL-M23(FF6P)Open-BK-100-IP67: 1-meter M23 to 6-pin power
cable with IP67-rated female 6-pin M23 connector
•CBL-M12D(MM4P)/RJ45-100 IP67: 1-meter M12-to-RJ45 Cat-5E UTP
Ethernet cable with IP67-rated male 4-pin M12 D-coded connector
•CBL-M12(FF5P)/OPEN-100 IP67: 1-meter M12-to-5-pin power cable
with IP67-rated female 5-pin M12 A-coded connector
•M12D-4P-IP68: Field-installable M12 D-coded screw-in connector,
male 4-pin, IP68-rated
•M12A-5P-IP68: Field-installable M12 A-coded screw-in connector,
female 5-pin, IP68-rated
•CAP-M12F-M: Metal cap for M12 female connector
•DK-DC50131: DIN rail mounting kit, 50 x 131 mm
www.ipc2u.ru
www.moxa.pro

- 4 -
TN-5510A-2GLSX-ODC Panel Layouts
1. Screw holes for panel mounting kit
2. Console port
3. Grounding screw
4. Relay output port
5. Power input voltage range indicator
6. Power input port (male 6-pin shielded M23 connector)
7. PWR1 LED: for power input 1
www.ipc2u.ru
www.moxa.pro

- 5 -
8. PWR2 LED: for power input 2
9. FAULT LED
10. MSTR/HEAD LED: for ring master or chain head
11. CPLR/TAIL LED: for ring coupler or chain tail
12. TP port’s 10/100 Mbps LED
13. 10/100BaseT(X) port (female 4-pin shielded M12 connector with D
coding)
14. Waterproof vent
15. Product label
16. 12 screw holes for DIN rail mounting kit
17. E2 LED: Down-side E2 Gigabit port’s 1000 Mbps LED
18. E1 LED: Down-side E1 Gigabit port’s 1000 Mbps LED
19. Gigabit fiber port E1 (corresponding to port 9 in the TN-5510A User’s
Manual)
20. Gigabit fiber port E2 (corresponding to port 10 in the TN-5510A
User’s Manual)
ATTENTION
Please DO NOT open or remove vent 15. The warranty will be
invalid if the seal is removed.
All exposed connectors, including 3, 5, 7, and 14, should be
tightly covered by protective caps when they are not in use to
ensure IP54 protection.
www.ipc2u.ru
www.moxa.pro

- 6 -
Mounting Dimensions (unit = mm)
TN-5510A-2GLSX-ODC Series
www.ipc2u.ru
www.moxa.pro

- 7 -
TN-5510A-8PoE-2GLSX-ODC Series
www.ipc2u.ru
www.moxa.pro

- 8 -
Panel/Wall Mounting
STEP 1:
Mounting the TN-5510A to a wall requires 4 screws. Use the ToughNet
switch as a guide to mark the correct positions of the 4 screws.
STEP 2:
Use the 4 screws in the panel
mounting kit. If you would like to use
your own screws, make sure the
screw head is between 6.0 mm
and 7.0 mm in diameter and the
shaft is less than 4.0 mm in
diameter, as shown at the right.
Do not screw the screws in all the way—leave a space of about 2 mm to
allow room for sliding the ToughNet switch between the wall and the
screws.
NOTE
Before tightening the screws into the wall, make sure the screw
head and shaft size are suitable by inserting the screw through
one of the keyhole-shaped apertures of the ToughNet switch.
STEP 3:
Once the screws are fixed in the wall, hang the ToughNet switch on the 4
screws through the large opening of the keyhole-shaped apertures, and
then slide the switch downwards. Tighten the four screws for added
stability.
NOTE
To provide greater protection from vibration and shock, use
screws with shaft diameter between 6.0 mm and 7.0 mm, and fix
the ToughNet switch onto the wall directly through the large
opening of the keyhole-shaped apertures.
www.ipc2u.ru
www.moxa.pro

- 9 -
DIN Rail Mounting (optional)
Use a pair of optional DK-DC50131 DIN
rail mounting kits (must be purchased
separately) to mount the TN-5510A on
a 35 mm DIN rail.
STEP 1:
Use 12 screws (6 screws per plate) to
attach the two DIN rail attachment
plates to the rear panel of the switch.
STEP 2:
If the spring-loaded bracket is locked in place, push the recessed button
to release it. Once released, you should feel some resistance from the
spring as you slide the bracket up and down a few millimeters in each
direction.
STEP 3:
Insert the top of the DIN rail into
the top slot of the DIN rail
attachment plates.
STEP 4:
The DIN rail attachment plates will
snap into position, as shown in the
figure below.
To remove the Moxa ToughNet Switch from the DIN rail, use a
screwdriver to pull down the bottom parts of the two spring-loaded
brackets until they are fixed in the “locked” position, and then reverse
Steps 3 and 4 above.
www.ipc2u.ru
www.moxa.pro

- 10 -
Wiring Requirements
WARNING
Turn the power off before disconnecting modules or wires. The
correct power supply voltage is listed on the product label. Check
the voltage of your power source to make sure you are using the
correct voltage. Do NOT use a voltage greater than what is
specified on the product label.
These devices must be supplied by a SELV source as defined in
the Low Voltage Directive 2006/95/EC and 2004/108/EC.
ATTENTION
Safety First!
Observe all electrical codes dictating the maximum current
allowable for each wire size. If the current goes above the
maximum ratings, the wiring could overheat, causing serious
damage to your equipment.
ATTENTION
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your Moxa switch.
This device has UL 508 approval. Use copper conductors only,
60/75°C, and tighten to 4.5 pound-inches. For use in pollution
degree 2 environments.
Please read and follow these guidelines:
•Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
NOTE
Do not run signal or communications wiring and power wiring
through the same wire conduit. To avoid interference, wires with
different signal characteristics should be routed separately.
•You can use the type of signal transmitted through a wire to
determine which wires should be kept separate. The rule of thumb is
that wiring that shares similar electrical characteristics can be
bundled together.
•Keep input wiring and output wiring separated.
•It is strongly advised that you label wiring for all devices in the system
when necessary.
www.ipc2u.ru
www.moxa.pro