Moxa Technologies airworks awk-5232 User manual

Moxa AirWorks AWK-5232 User’s Manual
First Edition, October 2011
www.moxa.com/product
© 2011 Moxa Inc. All rights reserved.

Moxa AirWorks AWK-5232 User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in accordance with
the terms of that agreement.
Copyright Notice
© 2011 Moxa Inc. All rights reserved.
Trademarks
The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the part of
Moxa.
Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited
to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the
products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for
its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Americas
Toll
-free: 1-888-669-2872
Tel:
[phone]
Fax:
[phone]
Moxa China (Shanghai office)
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe
Tel:
[phone]
Fax:
[phone]
Moxa Asia
-Pacific
Tel:
[phone]
Fax:
[phone]

Table of Contents
1. Introduction...................................................................................................................................... 1-1
Overview...........................................................................................................................................1-2
Package Checklist...............................................................................................................................1-2
Product Features ................................................................................................................................1-2
Product Specifications .........................................................................................................................1-3
Functional Design ...............................................................................................................................1-3
LED Indicators ............................................................................................................................1-3
Beeper.......................................................................................................................................1-4
Reset Button...............................................................................................................................1-4
Relay (Digital Output)..................................................................................................................1-4
Antenna.....................................................................................................................................1-5
2. Getting Started.................................................................................................................................. 2-1
First-time Installation and Configuration................................................................................................2-2
Communication Testing .......................................................................................................................2-3
Function Guiding Map..........................................................................................................................2-4
3. Web Console Configuration ............................................................................................................... 3-1
Configuration by Web Browser .............................................................................................................3-2
Overview...........................................................................................................................................3-3
Basic Settings ....................................................................................................................................3-4
System Info Settings ...................................................................................................................3-4
Network Settings.........................................................................................................................3-4
Time Settings .............................................................................................................................3-5
Wireless Settings................................................................................................................................3-6
Operation Mode...........................................................................................................................3-6
WLAN1/WLAN2 ...........................................................................................................................3-9
Enabling Non-Redundant (Single RF) AP.........................................................................................3-9
WLAN Security Settings..............................................................................................................3-12
Advanced Wireless Settings........................................................................................................3-19
WLAN Certification Settings (for EAP-TLS in Redundant Client, Client or Slave mode only)..................3-22
Advanced Settings............................................................................................................................3-22
Using Virtual LAN ......................................................................................................................3-23
Configuring Virtual LAN..............................................................................................................3-24
DHCP Server (for AP-Client operation mode’s AP mode only) ..........................................................3-25
Packet Filters............................................................................................................................3-26
RSTP Settings (for Master or Slave mode only) .............................................................................3-28
SNMP Agent.............................................................................................................................. 3-30
Storm Protection.......................................................................................................................3-31
Link Fault Pass-Through (for Client/Slave mode only) ....................................................................3-32
Auto Warning Settings.......................................................................................................................3-32
System Log ..............................................................................................................................3-32
Syslog .....................................................................................................................................3-33
E-mail......................................................................................................................................3-34
Relay.......................................................................................................................................3-36
Trap ........................................................................................................................................3-36
Status .............................................................................................................................................3-38
Wireless Status.........................................................................................................................3-38
Associated Client List (for Redundant AP, AP, or Master mode only).................................................3-38
DHCP Client List (for AP mode only).............................................................................................3-39
System Log ..............................................................................................................................3-39
Relay Status ............................................................................................................................. 3-40
DI and Power Status..................................................................................................................3-40
Relay Status ............................................................................................................................. 3-40
Maintenance ....................................................................................................................................3-41
Console Settings .......................................................................................................................3-41
Ping.........................................................................................................................................3-41
Firmware Upgrade.....................................................................................................................3-42
Config Import Export .................................................................................................................3-42
Load Factory Default..................................................................................................................3-42
Password..................................................................................................................................3-43
Misc. Settings ...........................................................................................................................3-43
Save Configuration ...........................................................................................................................3-43
Restart............................................................................................................................................ 3-44
Logout.............................................................................................................................................3-45
4. Software Installation/Configuration................................................................................................. 4-1
Overview...........................................................................................................................................4-2
AWK Search Utility..............................................................................................................................4-2
Installing AWK Search Utility ........................................................................................................4-2

Configuring AWK Search Utility .....................................................................................................4-4
5. Other Console Configurations............................................................................................................ 5-1
RS-232 Console Configuration (115200, None, 8, 1, VT100) ....................................................................5-2
Configuration by Telnet and SSH Consoles.............................................................................................5-4
Configuration by Web Browser with HTTPS/SSL......................................................................................5-4
Disabling Telnet and Browser Access.....................................................................................................5-5
6. References ........................................................................................................................................ 6-1
Beacon..............................................................................................................................................6-2
DTIM.................................................................................................................................................6-2
Fragment...........................................................................................................................................6-2
RTS Threshold....................................................................................................................................6-2
STP and RSTP ....................................................................................................................................6-2
The STP/RSTP Concept ................................................................................................................6-2
Differences between RSTP and STP................................................................................................6-3
7. Supporting Information .................................................................................................................... 7-1
About This User’s Manual.....................................................................................................................7-2
DoC (Declaration of Conformity)...........................................................................................................7-2
Federal Communication Commission Interference Statement............................................................7-2
R&TTE Compliance Statement.......................................................................................................7-3
Firmware Recovery .............................................................................................................................7-3
Technical Support Contact Information..................................................................................................7-5

1
1. Introduction
Moxa AirWorks AWK-5232 with dual-RF wireless capability allows wireless users to access network resources
more reliably. The AWK-5232 is rated to operate at temperatures ranging from 0 to 60°C for standard models
and -40 to 75°C for extended temperature models, and is rugged enough for any harsh industrial environment.
The following topics are covered in this chapter:

Overview

Package Checklist

Product Features

Product Specifications

Functional Design
LED Indicators
Beeper
Reset Button
Relay (Digital Output)
Antenna

AWK-5232 Introduction
1-2
Overview
The AWK-5232 Industrial a/b/g/n Wireless AP/Bridge/Client is an ideal wireless solution for connecting mobile
equipment connected over a TCP/IP network in hard-to-wire situations. The AWK-5232 provides faster
throughput than standard 802.11g devices, and at temperatures ranging from 0 to 60°C for standard models
to -40 to 75°C for wide temperature models, making the AWK-5232 series rugged enough for any industrial
environment. With two independent RF modules, the AWK-5232 supports a great variety of wireless
configurations and applications, and the redundant wireless connections increase the reliability of the entire
wireless network. The AWK-5232's two DC power inputs make the power supply more reliable, and it can be
powered via PoE+ for easier deployment.
Package Checklist
Moxa’s AWK-5232 is shipped with the following items. If any of these items is missing or damaged, please
contact your customer service representative for assistance.
•1 AWK-5232
•4 Swivel-type Antennas (2 dBi, RP-SMA, 2.4 & 5 GHz)
•1 Quick Installation Guide
•1 Software CD
•1 Moxa Product Warranty Booklet
•1 Cable Holder with a Screw
•Protective Caps
NOTE
The above items
come with the AWK-5232 standard version. The package contents may vary in a
customized
version.
Product Features
•IEEE 802.11a/b/g/n compliant
•Three-in-one design (AP/Bridge/Client)
•Dual-RF design for redundant wireless communication
•Advanced wireless security:
64-bit and 128-bit WEP/WPA/WPA2
SSID Hiding/IEEE 802.1X/RADIUS
Packet access control & filtering
•STP/RSTP support for redundancy of system networking
•Dedicated antenna selection
•Free firmware update for more advanced functions
•RS-232 console management
•2DI+1DO for on-site monitoring and warming
•Operating temperature ranges from -40 to 75°C (-T model)
•Power input by redundant 24 VDC power inputs or IEEE802.3at Power over Ethernet Plus
•DIN-Rail or wall mounting ability
•IP30 protected high-strength metal housing

AWK-5232 Introduction
1-3
Product Specifications
ATTENTION
The AWK
-5232 is NOT a portable mobile device and should be located at least 20cm away from the human
body. The AWK
-5232 is NOT designed for the general public. To safely deploy the AWK-5232s within
a wireless
network
, a well-trained technician is required for installation.
Functional Design
LED Indicators
The LEDs on the front panel of the AWK-5232 allow you to quickly identity device status and wireless settings.
LED Color State Description
Front Panel LED Indicators (System)
PWR1 Green On Power is being supplied from power input 1.
Off Power is not being supplied from power input 1.
PWR2 Green On Power is being supplied from power input 2.
Off Power is not being supplied from power input 2.
PoE+ Amber On Power is being supplied via PoE+
Off Power is not being supplied via PoE+.
FAULT Red Blinking Cannot get an IP address from the DHCP server
(interval: 1 sec)
Off There is no error condition.
STATE Green/Red Green Software Ready
Blinking Green The AWK has been located by AWK Search
Utility(interval: 1 sec)
Red Booting or Error condition
WLAN1 Green/Amber Green On WLAN1 functions in Client mode.
Blinking Green WLAN1’s data communication is running in Client
mode
Amber On WLAN1 functions in AP/Bridge mode.
Blinking Amber WLAN1’s data communication is running in
AP/Bridge mode
Off WLAN1 is not in use.
WLAN2 Green/Amber Green On WLAN2 function is in Client mode.
Blinking Green WLAN2’s data communication is running in Client
mode
Amber On WLAN2 function is in AP/Bridge mode.
Blinking Amber WLAN2’s data communication is running in
AP/Bridge mode
Off WLAN2 is not in use.
TP Port (LAN1, LAN2) LED Indicators (Port Interface)
100M Amber On TP port’s 10/100 Mbps link is active.
Blinking Data is being transmitted at 10/100 Mbps
Off TP port’s 10/100 Mbps link is inactive.

AWK-5232 Introduction
1-4
LED Color State Description
1000M Green On TP port’s 1000 Mbps link is active.
Blinking Data is being transmitted at 1000 Mbps
Off TP port’s 1000 Mbps link is inactive.
ATTENTION
When the LEDs for
STATE (Green), FAULT, WLAN1 and WLAN2 all light up simultaneously and blink at
one
-second intervals, it means the system has failed to boot. This may be due to improper operation or
uncontrollable issues, such as an unexpected shutdown during
a firmware update. To recover the firmware,
refer to
“Firmware Recovery” in Chapter 7.
Beeper
The beeper signals that the system is ready with two short beeps.
Reset Button
The RESET button is located on the top panel of the AWK-5232. You can reboot the AWK-5232 or reset it to
factory defaults by pressing the RESET button with a pointed object, like a straightened paper clip.
•System reboot:Hold the RESET button down for under 5 seconds and then release.
•Reset to factory default:Hold the RESET button down for over 5 seconds until the STATE LED starts
blinking green. Release the button to reset the AWK-5232.
Relay (Digital Output)
The AWK-5232 has one relay output, which consists of the 2 terminal block contacts on the top panel, as shown
below. These relay contacts are used to forward notifications of system failure and user-configured events.
The two wires attached to the relay contacts form an open circuit when a user-configured event is triggered. If
a user-configured event does not occur, the relay circuit will remain closed. For safety reasons, the relay circuit
is kept open when the AWK-5232 is not powered.
The AWK-5232’s relay status is summarized as follows:
Power Status Event Relay
Off --- Open
On Yes Open
No Short

AWK-5232 Introduction
1-5
Antennae
The AWK-5232 supports 802.11 a/b/g/n with 2x2 MIMO technology and a dual RF solution. Antennas 1A and
1B are the MIMO antennas associated with RF1, and 2A and 2B are the MIMO antennas associated with RF2.
1A
2A
2B 1B
units = mm (in)

2
2. Getting Started
This chapter explains how to install Moxa’s AirWorks AWK-5232 for the first time, to quickly set up your
wireless network and test whether the connection is running well. With this function guide, you will gain access
to the functions you need easily.
The following topics are covered in this chapter:

First-time Installation and Configuration

Communication Testing

Function Guiding Map

AWK-5232 Getting Started
2-2
First-time Installation and Configuration
Before installing the AWK-5232, make sure that all items in the Package Checklist are in the box. In addition,
you will need access to a notebook computer or PC equipped with an Ethernet port. The AWK-5232 has a
default IP address that you must use when connecting to the device for the first time.
Step 1: Select the power source.
The AWK-5232 can be powered by DC power input or PoE+ (Power over Ethernet Plus). The AWK-5232 will use
whichever power source you choose.
ATTENTION
Do
NOT use either an IEEE802.3af PoE Injector NOR a PSE (Power Sourcing Equipment). Use
only
an IEEE802.3at compliant PSE for PoE+ (Power over Ethernet
Plus) device.
Step 2: Connect the AWK-5232 to a notebook or PC.
Since the AWK-5232 supports MDI/MDI-X auto-sensing, you can use either a straight through cable or
crossover cable to connect the AWK-5232 to a computer. If the LED indicator on AWK-5232’s LAN port lights up,
it means the connection is established.
Step 3: Set up the computer’s IP address.
Set an IP address on the same subnet as the AWK-5232. Since the AWK-5232’s default IP address is
192.168.127.253, and the subnet mask is 255.255.255.0, you should set the IP address of the computer to
192.168.127.xxx.
NOTE
After you select
Maintenance

Load Factory Default and click the Submit button, the AWK-
5232 will be
reset to
factory default settings and the IP address will be also reset to 192.168.127.253.
Step 4: Use the web-based manager to configure AWK-5232
Open your computer’s web browser and type http://192.168.127.253 in the address field to access the
homepage of the web-based Network Manager. Before the homepage opens, you will need to enter the user
name and password as shown in the following figure. For first-time configuration, enter the default username
and password and then click on the Login button:

AWK-5232 Getting Started
2-3
NOTE
Default user name and password:
Username: admin
Password: root
For security reasons, we strongly recommend changing the default password. To do so, select
Maintenance

Password
, and then follow the on-screen instructions to change the password.
NOTE
After you click
Submit to apply changes, you can see that the web page is refreshed, and the string
“(
Update)” and a blinking reminder will be shown on the upper-right corner of web page, as follow.
To make the changes effective, click
Restart and then Save and Restart
after you change the settings. About
30 seconds are needed for the AWK
-5232 to complete its restart process.
Step 5: Select the operation mode for the AWK-5232.
By default, the AWK-5232’s operation mode is set to Wireless redundancy. You can change the setting in
Wireless Settings Operation mode if you would like to use the Wireless bridge or AP-Client mode instead.
Detailed information about configuring the AWK-5232’s operation can be found in Chapter 3.
Step 6: Test communications.
We will describe 2 test methods to make sure the network connection has been established. Please refer to the
following section for more details.
Communications Testing
After installation, you can run a sample test to make sure the AWK-5232 and wireless connection are
functioning normally. Two testing methods are explained in the following sections. Use the first method if you
are using only one AWK-5232 device, and use the second method if you are using two or more AWK-5232s.
Testing Method for one AWK-5232
If you are only using one AWK-5232, you will need a second notebook computer equipped with a WLAN card.
Configure the WLAN card to connect to the AWK-5232 (NOTE: the default SSID is MOXA_1), and change the
IP address of the second notebook (B) so that it is on the same subnet as the first notebook (A), which is
connected to the AWK-5232.
After configuring the WLAN card, establish a wireless connection with the AWK-5232 and open a DOS window
on Notebook B. At the prompt, type
ping <IP address of notebook A>
and then press Enter (see the figure below). A “Reply from IP address …” response means the communication
was successful. A “Request timed out.” response means the communication failed. In this case, recheck the
configuration to make sure the connections are correct.

AWK-5232 Getting Started
2-4
Testing Method for two or more AWK-5232s
If you have two or more AWK-5232s, you will need a second notebook computer (B) equipped with an Ethernet
port. Use the default settings for the first AWK-5232 connected to notebook A and change the second or third
AWK-5232 connected to notebook B to Client mode. Then, configure the notebooks and AWK-5232s properly.
After setting up the testing environment, open a DOS window on notebook B. At the prompt, type
ping <IP address of notebook A>
and then press Enter. A “Reply from IP address …” response means the communication was successful. A
“Request timed out” response means the communication failed. In this case, recheck the configuration to make
sure the connections are correct.
Function Guiding Map
The management functions are categorized in a tree and shown in the left field of the web-based management
console. You can efficiently locate the function you need with the following guide.

AWK-5232 Getting Started
2-5
A quick overview of the AWK-5232’s status
Basic settings for administering the
AWK-5232
Essential settings related to establishing
a wireless network
Advanced features to support additional
network management and secure wired and
wireless communication
* These advanced functions are all optional.
Application-oriented device management
functions to set up events, traps, and
reactions via relay warning, e-mail and
SNMP notification
* These functions are all optional.
Real-time status information to monitor
wired/wireless network performance,
advanced services, and device
management functions
Functions to maintain the AWK-5232 and
diagnose the network
On-demand functions to support the
operations of web-based console
management

3
3. Web Console Configuration
In this chapter, we will explain each web management page of the web-based console configuration. Moxa’s
easy-to-use management functions will help you set up your AWK-5232, as well as establish and maintain your
wireless network easily.
The following topics are covered in this chapter:

Configuration by Web Browser

Overview

Basic Settings
System Info Settings
Network Settings
Time Settings

Wireless Settings
Operation Mode
WLAN1/WLAN2
Enabling Non-Redundant (Single RF) AP
WLAN Security Settings
Advanced Wireless Settings
WLAN Certification Settings (for EAP-TLS in
Redundant Client, Client or Slave mode only)

Advanced Settings
Using Virtual LAN
Configuring Virtual LAN
DHCP Server (for AP-
Client operation mode’s
AP mode only)
Packet Filters
RSTP Settings
(for Master or Slave mode only)
SNMP Agent
Storm Protection
Link Fault Pass-Through (for Client/Slave
mode only)

Auto Warning Settings
System Log
Syslog
E-mail
Relay
Trap

Status
Wireless Status
Associated Client List (for Red
undant AP, AP,
or Master mode only)
DHCP Client List (for AP mode only)
System Log
Relay Status
DI and Power Status

Maintenance
Console Settings
Ping
Firmware Upgrade
Config Import Export
Load Factory Default
Password
Misc. Settings

Save Configuration

Restart

Logout

AWK-5232 Web Console Configuration
3-2
Configuration by Web Browser
Moxa AWK-5232’s web browser interface provides a convenient way to modify its configuration and access the
built-in monitoring and network administration functions. The recommended web browser is Microsoft®
Internet Explorer 5.5 or 6.0 with JVM (Java Virtual Machine) installed.
NOTE
To use the AWK
-
5232’s management and monitoring functions from a PC host connected to the same LAN as
the AWK
-5232, you must make sure that the PC host and AWK-5232 are on the sa
me logical subnet. Similarly,
if the AWK
-
5232 is configured for other VLAN settings, you must make sure your PC host is on the management
VLAN.
The Moxa AWK
-5232’s default IP is 192.168.127.253.
Follow the steps below to access the AWK-5232’s web-based console management.
1. Open your web browser (ex. Internet Explorer) and type the AWK-5232’s IP address in the address field.
Then press Enter to establish the connection.
2. The Web Console Login page will open. Enter the password (Username is set as admin; the default
password is root if a new password has not been set.) and then click Login to continue.
You may need to wait a few moments for the web page download onto your computer. Please note that the
Model name and IP address of your AWK-5232 are both shown on the title of the web page. This information
can help you identify multiple AWK-5232s.
You can use the menu tree on the left side of the window to open the function pages to access each of
AWK-5232’s functions.

AWK-5232 Web Console Configuration
3-3
In the following paragraphs, we will go through each of the AWK-5232’s management functions in detail. You
can also get a quick overview of these functions in the “Function Guiding Map” section of Chapter 2.
NOTE
The model name of the AWK
-5232 is shown as AWK-5232-XX where XX indicates the
country code. The country
code represents the AWK
-5232 version and which bandwidth it uses. We use AWK-5232-US
as an example in
the following figures. The country code of model name on the screen may vary if you are using a different
version (band) AWK
-5232.
NOTE
For security reasons, you will need to log back into the AWK
-5232 after the 5-minute time-out.
Overview
The Overview page summarizes the AWK-5232’s current status. The information is categorized into several
groups: System Info, Device info and 802.11 Info.

AWK-5232 Web Console Configuration
3-4
Basic Settings
The Basic Settings group includes the most commonly used settings required by administrators to maintain and
control the AWK-5232.
System Info Settings
The System Info items, especially Device name and Device description, are displayed and included on the
Overview page, SNMP information, and alarm emails. Setting System Info items makes it easier to identify
the different AWK-5232s connected to your network.
Device name
Setting Description Factory Default
Max. 31 Characters This option is useful for specifying the role or application of
different AWK-5232 units. AWK-5232_<Serial No. of this
AWK-5232>
Device location
Setting Description Factory Default
Max. 31 Characters To specify the location of different AWK-5232 units. None
Device description
Setting Description Factory Default
Max. 31 Characters Use this space to record more detailed description of AWK-5232
None
Device name
Setting Description Factory Default
Max. 31 Characters To provide information about whom to contact in order to
resolve problems. Use this space to
record contact information
of the person responsible for maintaining this AWK-5232.
None
Network Settings
The Network Settings configuration allows you to modify the usual TCP/IP network parameters. An explanation
of each configuration item is given below.

AWK-5232 Web Console Configuration
3-5
IP configuration
Setting Description Factory Default
DHCP The AWK-5232’s IP address will be assigned automatically by
the network’s DHCP server Static
Static Set up the AWK-5232’s IP address manually.
IP address
Setting Description Factory Default
AWK-5232’s IP address
Identifies the AWK-5232 on a TCP/IP network. 192.168.127.253
Subnet mask
Setting Description Factory Default
AWK-5232’s subnet
mask Identifies the type of network to which the AWK-5232 is connected (e.g., 255.255.0.0 for a Class B network, or
255.255.255.0 for a Class C network).
255.255.255.0
Gateway
Setting Description Factory Default
AWK-5232’s default
gateway The IP address of the router that connects the LAN to an outside network. None
Primary/ Secondary DNS server
Setting Description Factory Default
IP address of Primary/
Secondary DNS server
The IP address of the DNS Server used by your network. After
entering the DNS Server’s IP address, you can input the
AWK-5232’s URL (e.g., http://ap11.abc.com
) in your browser’s
address field instead of entering the IP address. The Secondary
DNS server will be used if the Primary DNS server fails to
connect.
None
Time Settings
The AWK-5232 has a time calibration function based on information from an NTP server or user specified Date
and Time information. Functions such as Auto warning can add real-time information to the message.
Current local time shows the AWK-5232’s system time when you open this web page. You can click on the
Set Time button to activate the update after setting up the date and time parameters. An “(Updated)” string
will appear to indicate that the change is complete. Local time settings will be immediately activated in the
system without running Save and Restart.

AWK-5232 Web Console Configuration
3-6
NOTE
The AWK
-5232 has a real time clock (RTC). Users are strongly recommended to update the Local time
for the
AWK
-5232 after initial setup or long-term shutdown, especially when the network does not have an In
ternet
connection for
accessing the NTP server or there is no NTP server on the LAN.
Current local time
Setting Description Factory Default
User adjustable time The date and time parameters allow configuration of the local
time with immediate activation. None (yyyy/mm/dd
hh:mm:ss format;
24-hour format.)
Time zone
Setting Description Factory Default
User selectable time
zone The time zone setting allows conversion from
GMT (Greenwich
Mean Time) to local time. GMT (Greenwich
Mean Time)
ATTENTION
Changing the time zone will automatically adjust the
Current local time. You should configure the Time zone
before setting the
Current local time.
Daylight saving time
Setting Description Factory Default
Enable/ Disable Daylight saving time (also know as DST or summer time)
involves advancing clocks (usually 1 hour) during the summer
time to provide an extra hour of daylight in the afternoon.
Disable
When Daylight saving time is enabled, the following parameters can be shown:
•The Starts at parameter allows users to enter the date that daylight saving time begins.
•The Stops at parameter allows users to enter the date that daylight saving time ends.
•The Time offset parameter indicates how many hours forward the clock should be advanced.
Time server 1/ 2
Setting Description Factory Default
The 1st/ 2nd time
server IP/Name
IP or Domain address of NTP time server. The 2nd time will be
used if the 1st NTP server fails to connect. None
Query period
Setting Description Factory Default
Query period time
(1- 9999 seconds) This parameter determines how often
the time is updated from
the NTP server. 600 (seconds)
Wireless Settings
The essential settings for wireless networks are presented in this function group. Settings must be properly set
before establishing your wireless network.
Operation Mode
The AWK-5232 supports three operation modes that are used for different wireless network applications: