Moxa Technologies AWK-6232 User manual

P/N: 1802062320013
*1802062320013*
AWK-6232
Quick Installation Guide
Moxa AirWorks
Edition 4.0, July 2016
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll
-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax:
1-714-528-6778
Moxa China (Shanghai office):
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe:
Tel:
[phone]
Fax:
[phone]
Moxa Asia-Pacific:
Tel:
[phone]
Fax:
[phone]
Moxa India:
Tel:
[phone]
Fax:
[phone]

2016 Moxa Inc. All rights reserved.

- 2 -
Notes for the Reader
WARNING
I
ndicates that death or personal injury may occur if proper
precautions are not taken.
ATTENTION
Indicates that possible damage to this product or your property
may result if proper precautions are not taken.
NOTE
Highlights important information related to this product.
Package Checklist
Moxa’s AWK-6232 is shipped with the following items. If any of these
items is missing or damaged, contact your customer service
representative for assistance.
•AWK-6232 wireless AP/bridge/client
•4 Dual-band omnidirectional antennas (5/2 dBi, N-type male, 2.4
GHz /5 GHz)
•Wall-mounting kit (includes 2 supports)
•Field-installable power plug
•Field-installable Ethernet plug
•1 metal cap to cover RJ45 connector
•1 metal cap to cover M12-female LAN connector
•1 metal cap to cover M12-male DI/O connector
•2 transparent plastic sticks for field-installable plugs
•Documentation and software CD
•Quick installation guide (printed)
•Warranty card
Recommended SFP Accessories
SFP-1G series
•SFP-1GSXLC: Small form factor pluggable transceiver with
1000BaseSX, LC, 0.5 km, 0 to 60°C
•SFP-1GSXLC-T: Small form factor pluggable transceiver with
1000BaseSX, LC, 0.5 km, -20 to 75°C
•SFP-1GLSXLC: Small form factor pluggable transceiver with
1000BaseLSX, LC, 2 km, 0 to 60°C
•SFP-1GLSXLC-T: Small form factor pluggable transceiver with
1000BaseLSX, LC, 2 km, -40 to 85°C
•SFP-1GLXLC: Small form factor pluggable transceiver with
1000BaseLX, LC, 10 km, 0 to 60°C
•SFP-1GLXLC-T: Small form factor pluggable transceiver with
1000BaseLX, LC, 10 km, -40 to 85°C
•SFP-1GLHLC: Small form factor pluggable transceiver with
1000BaseLH, LC, 30 km, 0 to 60°C

- 3 -
•SFP-1GLHLC-T: Small form factor pluggable transceiver with
1000BaseLH, LC, 30 km, -40 to 85°C
•SFP-1GLHXLC: Small form factor pluggable transceiver with
1000BaseLHX, LC, 40 km, 0 to 60°C
•SFP-1GLHXLC-T: Small form factor pluggable transceiver with
1000BaseLHX, LC, 40 km, -40 to 85°C
•SFP-1GZXLC: Small form factor pluggable transceiver with
1000BaseZX, LC, 80 km, 0 to 60°C
•SFP-1GZXLC-T: Small form factor pluggable transceiver with
1000BaseZX, LC, 80 km, -40 to 85°C
•SFP-1GEZXLC: Small form factor pluggable transceiver with
1000BaseEZX, LC, 110 km, 0 to 60°C
•SFP-1GEZXLC-120: Small form factor pluggable transceiver with
1000BaseEZX, LC, 120 km, 0 to 60°C
NOTE
The above items come with the AWK-6232 standard version. The
package contents for customized versions may be different.
Installation
Before installing the AWK-6232, make sure that all items in the Package
Checklist are in the box. In addition, you will need access to a notebook
computer or PC equipped with an Ethernet port. The AWK-6232 has a
default IP address, user name and password that you must use when
resetting or connecting to your AWK-6232 device.
Default IP address: 192.168.127.253
User name: admin
Password: root
Please read “Chapter2 Getting Started” in AWK-6232 User’s Manual for
more details about installation and configuration.
ATTENTION
For security reasons, we strongly recommend changing the
password. To do so,
go to Maintenance

Password
, and then
follow the on-screen instructions.
NOTE
To make the change effective, you must save the change and
then click
Restart

Save and Restart button to apply all
changes.

- 4 -
Panel Layout of the AWK-6232
1.
RF 1’
s 1A and 1B antennas
2.
RF 2’
s 2A and 2B antennas
3.
LEDs for PWR, FAULT,
STATE, WLAN1, WLAN2,
LAN1, and LAN2
4.
M12 A-coding connector
for PWR1 and PWR2
5.
M12 8-pin connector for
DI/DO
6.
10/100/1000BaseT(X)
M12 Port: LAN1 and LAN2
7.
RS-232 console port
8.
Reset button
9.
Screw holes for wall
mounting
10.
Waterproof vent
11.
Grounding screw
12.
Screw holes for DIN-rail
mounting
ATTENTION
Please DO NOT open or remove the vent
(item 10, in the
diagram)
. The warranty will be invalid if the seal is removed.
All exposed connectors, including items
1,2,&4-7, should be
tightly covered by suitable caps when they are not in use.

- 5 -
Dimensions (unit = mm)
Attaching Antennas
The AWK-6232 includes two dual-band omnidirectional antennas by
default. Attach the antennas as illustrated below:
Step 1: Hold the antenna metal N-type connector.
Step 2: Screw the antenna N-type connector (male) onto the AWK-6232
device’s N-type connector (female)
Caution
Do not hold the rubber plate
to screw the antenna on to the
AWK-6232 device.
ATTENTION
Use the antennas correctly
!!
Use 2.4
GHz antennas if the AWK-6232 operates in IEEE
802.11b/g/n. Use the 5
GHz antennas for operations in
IEEE802.11a/n.
Make sure your antenna installation is within a
safe area covered by a lightning protection or surge arrest
system.
Antenna Metal N-type
Rubber plate

- 6 -
Wall Mounting
In most applications, wall mount provides an easier installation. You will
find it quite easy to mount AWK-6232 on the wall, as illustrated below.
STEP 1:
Attach the wall
-mounting kit
with M4 screws, as shown in
the diagram below.
STEP 2:
Mounting the AWK
-6232 on the wall
requires 4 screws. Use the AWK
-6232
device, with wall
-mounting kit
attached, as a guide to mark the correct
locations of the 4 screws. The heads of
the screws are recommended to be
between 5.5mm and 8.5 mm in
diameter, and the
shafts should
not
be
more than 5.0
mm in diameter, as
shown in the figure.
Do not drive the screws in all the way into the wall—leave a space of about
2 mm to allow room for sliding the wall-mounting kit between the wall and
the screws.
ATTENTION
Test the screw head and shank size by inserting the screws into
one of the keyhole shaped
apertures of the wall-
mounting plates
before attaching the plates to the wall.
STEP 3:
Once the screws are fixed into the wall, insert the four screw heads
through the large opening of the keyhole-shaped apertures, and then
slide the AWK-6232 downwards, as indicated to the right. Tighten the
four screws for added stability.
ATTENTION
To avoid environmental vibration or shock, you can consider a
robust installation with
four bigger screws, whose shafts are
between 7.0 mm a
nd 8.5 mm in diameter, and fix the AWK-
6232
directly onto wall before tightening the screws to secure it.

- 7 -
DIN-Rail Mounting (Optional)
The DK-DC50131 die-cast metal kit, which
can be bought separately,
is required to
enable easy and robust installation
for the
AWK
-6232. A pair of DK-DC50131s is
needed for DIN
-rail mounting of the
AWK
-6232. Attach the DIN-rail mounting
kits
to the rear panel of AWK-6232 with 12
screws. (6 screws for each kit)
as shown in
the illustration.
To Install
STEP 1:
Use the
recessed button
on the spring
-loaded
bracket to lock it into
position.
STEP 2:
Insert the top of the DIN rail into the slot just
b
elow the upper hook of the DIN-rail
mounting kit. Push the AWK
-6232 toward
the DIN r
ail until the DIN-rail attachment
bracket snaps into place.
To Release
STEP 1:
Pull out the two spring
-loaded
brackets
from the bottom until
they are fixed in the “release”
position.
STEP 2:
Pull the AWK
-
6232 out and upward.

- 8 -
Wiring Requirements
WARNING
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your Moxa AWK
-6232.
Calculate the maximum possible current in each power wire and
common wire. Observe all electrical codes dictating the
maximum current allowable for each wire size. If the current goes
above the maximum ratings, the wiring could overheat, causing
serious damage to your equipment.
You should also pay attention to the following items:
•Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
NOTE
Do not run signal or communications wiring and power wiring in
the same wire conduit. To avoid interference, wires with different
signal characteristics should be routed separately.
•You can use the type of signal transmitted through a wire to
determine which wires should be kept separate. The rule of thumb is
that wiring with similar electrical characteristics can be bundled
together.
•Keep input wiring and output wiring separate.
•It is strongly advised that you label wiring to all devices in the system
when necessary.
Grounding Moxa AWK-6232
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw to the grounding surface prior to connecting devices.
ATTENTION
This product is intended to be mounted to a well
-grounded
mounting surface, such as a metal panel. There must be no
p
otential difference between two ground potentials, otherwise
there is a risk that the device could be destroyed.
Installations with Unstable Power Inputs
There are cases where the device has to be wired to the same power
source as other equipment. In such cases if equipment such as motors
that are connected in the circuit draw a large amount of current during
operation, the transient voltage drop could potentially cause the AWK to
become unstable. Installing a DC/DC power isolator in between the two
equipment is recommended to isolate the transient effect and to ensure a

- 9 -
stable power input for the AWK.
Installations with Cable Extended Antennas for Outdoor
Applications
If the antenna or the AWK device is installed outdoors or in an open-air
setting, proper lightning protection is required to prevent direct lightning
strikes on the AWK device. In order to prevent coupling currents from
nearby lightning strikes, a lightning arrester should be installed as part of
your antenna system. Ground the device, antenna, as well as the arrester
properly to provide maximum outdoor protection for the device.

- 10 -
Arrester Accessories
•SA-NMNF-01: Surge arrester, N-type (male) to N-type (female)
•SA-NFNF-01: Surge arrester, N-type (female) to N-type (female)
Wiring the Redundant Power Inputs
The AWK-6232 must be connected to a Power over Ethernet Plus (PoE+)
IEEE 802.3at compliant power source or an IEC60950 compliant limited
power source. When AWK-6232 is powered via DC power, the M12
A-coding connector on the bottom panel is used for the AWK-6232’s two
redundant inputs. The male, device-side pin assignment is shown below:
Pin
Power Input
1
V1+
2
V2+
3
V1-
4
V2-
5
GND
ATTENTION
This product is intended to be supplied by a Listed Power Unit
marked “Class 2” or “LPS” and rated O/P:
18 W.
Make sure
the external power adapte
r (includes power cords and
plug assemblies) provided with the unit is certified and suitable
for use in your c
ountry.
Before connecting the AWK
-
6232 to the DC power inputs, make
sure the DC power source voltage is stable.
ATTENTION
Do not use a PoE injector with the PoE (Power
-over-Ethernet)
model. Instead, use an IEEE802.3af or
IEEE802.3at compliant
PSE (Power Sourcing Equipment).
Wiring the Digital Inputs and Relay Contact
(Digital Output)
The AWK-6232 has two sets of digital input—DI1 and DI2. Each DI
comprises two contacts of the 8-pin M12 connector on the AWK-6232’s
bottom panel. These two digital inputs can be connected to
digital-output-enabled sensors for on-site status monitoring.
The AWK-6232 also has one relay output, which consists of the two
contacts. These relay contacts are used to detect user-configured events.
The two wires attached to the Relay contacts form an open circuit when a
user-configured event is triggered. If a user-configured event does not
occur, the Relay circuit will be closed.
A field-installable plug, M12A-8PF-IP67, is recommended for
connecting the AWK-6232’s DIs and relay.