MSL JET PLUS 400 User manual

MSL Jet Plus 400/500 Getting Started
Component Check List
1. MSL Jet Plus 400/500
2. Autofeed(Option)
3. Hand Feed Platform
4. Platform Infill
5. ReceivingTray
6. Power Cable
7. Ink Cartridge
8. Telephone Adaptor
9. Telephone Cable
10. Weigh Platform (Option)
11. Platform Support (Option)
12. User’s Guide (Not Shown)
13. SelfAdhesiveLabels(30off)
(NotShown)
Items Sent Separately
SupervisorPIN,CredifonPIN
Detach
Platform Infill
Fittheslotsoverthetabs.
1
3
4
5
6
7
10
11
9
82
Pins on underside of support mate with
locationpointsoncasing.
If you have anAutofeeder then follow Steps 2 & 3.
If not go straight to Step 4.
3Fittheslotsoverthetabs.
Attach Platform
Infill to Autofeed
(Option) or Plain
Platform supplied
with the base
Upper 9 pin connector is used
if MailManager II option is used
Unpack Boxes
123Attach MSL Jet
Plus 400/500
4
Attach Weight Platform &
Support (Options)
5Connect Weigh Platform
Scale (Options) to lower
9 pin connector
67Connect Autofeed
(Option) 8Connect Telephone
Cable

After a short delay the
prompt to make aTest Print
willbe observed:
To make a test print, insert a blank envelope or card.
Press key.
Inspect the test print and enter the number corresponding
to best alignment:
e.g.
Press to confirm.
Thefollowingscreenwillnow
beobserved.
Holdleverfullylefttheninsert
Max.50labels.
Again using the key or the appropriate number key,
move the cursor to option 7 TELEPHONE SETTINGS and
press to confirm, the TELEPHONE SETTINGS
screen will now be observed:
Movethe cursortoPREFIXand press to confirm, the
PREFIX screen will be observed:
UsingthenumericalkeypadentertherequiredPrefixandpress
to confirm.
Press three times, the SLEEP screen will now be
observed:
Press the key.
TheprompttoENTERUSERPINwillbeobserved:
Enter the Default User PIN 1 2 3 4.
You are now ready to add credit to your machine.
Switch on the power at the supply outlet.
After a short delay, the following screen
willbe observed:
Press the key.
If the machine is protected by a User PIN, the prompt
toENTERUSERPINwillbeobserved:
TheDefault UserPINis factorysetto1 2 3 4.
Ifthe correct PIN is enteredthe INSERTCARTRIDGE
screenwill beobserved.
UnpacktheInkCartridge (Item 7)
andcarefullyremove Openthe top cover.
both tape seals.
DoNOT touchorremove
the copper strip on Ink
Cartridges.
Place the ink cartridge into its holder. From the front top edge of the cartridge push the
cartridge firmly up and to the back (see arrow) until it CLICKS into place, the cartridge
shouldnowbefirmlylockedintoposition.Closethemachinetopcoverandpress .
You Are Now Ready to Frank Your Mail
Themachinewillnowshowthe
followingscreen:
Press
Enter your Credifon PIN.
The prompt to ENTER AMOUNT will be observed:
e.g. £50.00
Press
Press .
IfamountIncorrect,press to return to ENTER AMOUNT
If amount Correct, press .
Oncompletionofthecrediting
procedure the following
screen will be observed:
Press to go to READY Mode.
CREDIFONPIN
____
ENTERAMOUNT
0.00
RECREDIT SUCCESSFUL
50.00
CONFIRMAMOUNT
50.00
INSPECTIONDUE-RECREDIT
CALLCREDIFON
22/06/2010 - 4146674B/B
Connect
Power Cord
9Position
Receiving Tray
10 Install the Ink Cartridge
11 Set Print Alignment
12
Connecting to the Credifon Centre
13
Add Credit
14 15 Fill the Label Hopper
If your telephone line is routed through a switchboard, the
Credifon Crediting Centre telephone number must be prefixed
by the appropriate outside line digit, if you are connecting by
way of a direct line, proceed to operation 14 .
The procedure to amend the stored telephone number is as
follows:
From the Ready Mode screen, press the key, the following
screen will be observed:
Using the and keys,or the appropriate number
key, move the cursor to 3 SUPERVISOR and press to
confirm, the following prompt will now be observed.
EntertheSUPERVISORPIN.
The SUPERVISOR screen will now be observed:
Using the & keys or the appropriate number
key, move the cursor to SETUP and press to confirm.
The SETUP screens will now be observed:
Screen1
By scrolling passed option 5 MOTOR TIMEOUT screen 2 will
be displayed:
Screen2
MAIN MENU
1 REGISTERS
2 CARTRIDGE
3 SUPERVISOR
4CLEAR MAIL PATH
5 WEIGHING MODE Differential OKESC
Printing
Surface
Tab
SUPERVIS USER
SUPERVIS USER