Multiplex CHANNEL PLUS DMD-16 User manual

Multiplex Technology, Inc. warrants this product to be free from
defects in materials and workmanship for a period of one year from
the date of purchase or MTI will repair, or at its option, replace the
defective product. To obtain warranty service, call MTI for a return
material authorization (RMA) number and return the product prepaid
to Multiplex Technology, Inc., 3001 Enterprise Street, Brea, CA
92821, Attention: Customer Service. Please put the RMA number on
the outside of the carton.
A
ny implied warranty arising from the sale of the product including
implied warranties of merchantability and fitness for purpose are
limited to the warranty stated above. MTI shall not be responsible for
losses or damages or expenses, whether direct, consequential or
incidental arising from the use of or the inability to use this product.
Some states do not allow limitations on how long the implied
warranty lasts or the exclusion or limitation or incidental or
consequential damages, so the above limitations and exclusions
may not apply to you. This warranty gives you specific legal rights,
and you may have other rights which may vary from state to state.
Warranty
600-242 REV A Multiplex Technology, Inc., Brea, CA 92821-6213
B) Never install telephone jacks in a wet location.
A) Never install telephone wiring during a lighting storm.
D) Use caution when installing or modifying telephone lines.
C) Never touch uninsulated telephone wires or terminals
unless the telephone line has been disconnected at the
network interface.
SAFETY INFORMATION:
IMPORTANT INSTRUCTIONS:
When you use your telephone equipment, basic precautions should always
be followed to reduce the risk of fire, electric shock and injury to persons,
includingthefollowing:
1. Read and understand instructions.
2. Do not use this product near water, for example, near a bathtub, wash
bowl, kitchen sink, or laundry tub, in a wet basement, or near a swim-
ming pool.
3. Never push objects of any kind into this product through cabinet slots as
they may touch dangerous voltages.
4. Use on UL listed cabinets like the H218A or H236A.
SAVE THESE INSTRUCTIONS
Data Distribution Module
Model DMD-16
Designed for
ChannelPlus and OpenHouse
structured wire grid systems.
multiplex
®
technology, inc.
3001 Enterprise Street, Brea, CA 92821-6213, U.S.A.
714-996-4100 800-999-5225 Fax [phone] www.channelplus.com
TM
Data Distribution Module DMD-1
6
Category 5e Compliant
multiplex
®
technology, inc.

2
Installation in stuctured wire enclosure
typical DSL modem
Keep sheath close to connector
Untwist .5” max.
TRTRT TRR
12345 768
PR2
PR1
PR3 PR4
RJ-45 (wired to TIA T568A standard)
Ethernet (both 10BaseT and 100BaseT)
8 position modular connector Wiring a 110 connector (a)
To data jacks in remote
wall plates. Connect up
to 7 computers.
Many modems may be
mounted by using an MB-55
or MB-56 mounting bracket
DSL modem
INOUT
DSL connection to telephone
MB-55 mounting
bracket
Residential Gateway model 8157
Residential Gateway model 8157
M2
Loop
M1
COM
COM
Col
PwrWAN
x3 x4 x5 x6 x7
TM
TM
x2
8157 Gateway
x2
TM
Data Distribution Module DMD-1
6
Category 5e Compliant
DMD-16
Category 5e Compliant
Included: (2) Flat Surface Mounting Ears. (1) Disconnect Jumper
(66) Labels
3
110 punch down tool
The 110 is a sophisticated insulation displacement
connection system. To push the wires between the
contact blades, use only a 110 punch down tool.
Using a screwdriver may not seat the wire properly
and can damage the contacts.
Installation in stuctured wire enclosure
typical Cable modem
To data jacks in remote
wall plates. Connect up to
7 computers.
Residential Gateway model 8157
Residential Gateway model 8157
M2
Loop
M1
COMCol
PwrWAN
x3 x4 x5 x6 x7
TM
x2
8157 Gateway
x2
TM
Data Distribution Module DMD-1
6
Category 5e Compliant
Wiring a 110 connector (b)
Cable modem
OUT IN
From Cable Company
To TVs
Filter
Usually supplied by
Cable Company
DMD-16
multiplex
®
technology, inc.