MULTIQUIP Whiteman Series User manual

To find the latest revision of this publication or
associated parts manual, visit our website at:
www.multiquip.com
OPERATION MANUAL
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
Revision #3 (08/30/19)
PN: 23624
SERIES
MODELS
JWN24HTCSL
JWN24HSCSL
RIDE-ON POWER TROWELS
(HONDA GX690RTAF GASOLINE ENGINE)
STARTING S/N VB0206952

PAGE 2 — JWN-SERIES RIDE-ON POWER TROWEL • OPERATION MANUAL — REV. #3 (08/30/19)
PROPOSITION 65 WARNING

JWN-SERIES RIDE-ON POWER TROWEL • OPERATION MANUAL — REV. #3 (08/30/19) — PAGE 3
Grinding/cutting/drilling of masonry, concrete, metal and
other materials with silica in their composition may give
off dust or mists containing crystalline silica. Silica is a
basic component of sand, quartz, brick clay, granite and
numerous other minerals and rocks. Repeated and/or
substantial inhalation of airborne crystalline silica can
cause serious or fatal respiratory diseases, including
silicosis.Inaddition, California and some other
authorities have listed respirable crystalline silica as a
substance known to cause cancer. When cutting such
materials, always follow the respiratory precautions
mentioned above.
WARNING
Grinding/cutting/drilling of masonry, concrete, metal and
other materials can generate dust, mists and fumes
containing chemicals known to cause serious or fatal
injury or illness, such as respiratory disease, cancer,
birth defects or other reproductive harm. If you are
unfamiliar with the risks associated with the particular
process and/or material being cut or the composition of
the tool being used, review the material safety data
sheet and/or consult your employer, the material
manufacturer/supplier, governmental agencies such as
OSHA and NIOSH and other sources on hazardous
materials. California and some other authorities, for
instance, have published lists of substances known to
cause cancer, reproductive toxicity,or other harmful
effects.
Control dust, mist and fumes at the source where
possible. In this regard use good work practices and
follow the recommendations of the manufacturers or
suppliers, OSHA/NIOSH, and occupational and trade
associations.Water should be used for dust
suppression when wet cutting is feasible. When the
hazards from inhalation of dust, mists and fumes cannot
be eliminated, the operator and any bystanders should
always wear a respirator approved by NIOSH/MSHA for
the materials being used.
WARNING
SILICOSIS WARNING RESPIRATORY HAZARDS
SILICOSIS/RESPIRATORY WARNINGS

PAGE 4 — JWN-SERIES RIDE-ON POWER TROWEL • OPERATION MANUAL — REV. #3 (08/30/19)
TABLE OF CONTENTS
JWN Series Ride-On Trowel
Proposition 65 Warning ........................................... 2
Silicosis/Respiratory Warnings ................................ 3
Table of Contents..................................................... 4
Training Checklist .................................................... 6
Daily Pre-Operation Checklist ................................. 7
Safety Information ............................................. 8–14
Lifting and Transporting ................................... 15–17
Specifications ........................................................ 18
Dimensions............................................................ 19
General Information............................................... 20
Components .................................................... 21–23
Setup ..................................................................... 24
Inspection ........................................................ 25–26
Operation......................................................... 27–29
Maintenance.................................................... 30–43
Wiring Diagram................................................ 44–45
Wiring Diagram Component Locator ..................... 46
Troubleshooting ............................................... 47–50
NOTICE
Specifications are subject to change without notice.

JWN-SERIES RIDE-ON POWER TROWEL • OPERATION MANUAL — REV. #3 (08/30/19) — PAGE 5
NOTES

PAGE 6 — JWN-SERIES RIDE-ON POWER TROWEL • OPERATION MANUAL — REV. #3 (08/30/19)
TRAINING CHECKLIST
Training Checklist
No, Description OK? Date
1Read operation manual
completely.
2
Machine layout, location of
components, checking of engine
oil levels.
3 Fuel system, refueling procedure.
4 Operation of spray and lights.
5Operation of controls (machine
not running).
6Safety controls, safety stop switch
operation.
7 Emergency stop procedures.
8Startup of machine, pre-heat,
engine choke.
9 Maintaining a hover.
10 Maneuvering.
11 Pitching.
12 Matching blade pitch. Twin-Pitch™
13 Concrete finishing techniques.
14 Shutdown of machine.
15 Lifting of machine (lift loops).
16 Machine transport and storage.

JWN-SERIES RIDE-ON POWER TROWEL • OPERATION MANUAL — REV. #3 (08/30/19) — PAGE 7
DAILY PRE-OPERATION CHECKLIST
Daily Pre-Operation Checklist      
1 Engine oil level
2 Condition of blades
3 Blade pitch operation
4 Safety stop switch operation
5 Steering control operation

PAGE 8 — JWN-SERIES RIDE-ON POWER TROWEL • OPERATION MANUAL — REV. #3 (08/30/19)
SAFETY INFORMATION
Do not operate or service the equipment before reading
the entire manual. Safety precautions should be followed
at all times when operating this equipment.
Failure to read and understand the safety
messages and operating instructions could
result in injury to yourself and others.
SAFETY MESSAGES
The four safety messages shown below will inform you
about potential hazards that could injure you or others.The
safety messages specifically address the level of exposure
to the operator and are preceded by one of four words:
DANGER, WARNING, CAUTION
or NOTICE.
SAFETY SYMBOLS
DANGER
Indicates a hazardous situation which, if not avoided,
WILL result in DEATH or SERIOUS INJURY.
WARNING
Indicates a hazardous situation which, if not avoided,
COULD result in DEATH or SERIOUS INJURY.
CAUTION
Indicates a hazardous situation which, if not avoided,
COULD result in MINOR or MODERATE INJURY.
NOTICE
Addresses practices not related to personal injury.
Potential hazards associated with the operation of this
equipment will be referenced with hazard symbols which
may appear throughout this manual in conjunction with
safety messages.
Lethal exhaust gas hazards
Explosive fuel hazards
Burn hazards
Rotating parts hazards
Symbol Safety Hazard
Pressurized fluid hazards
Hydraulic fluid hazards

JWN-SERIES RIDE-ON POWER TROWEL • OPERATION MANUAL — REV. #3 (08/30/19) — PAGE 9
SAFETY INFORMATION
SAFETY DECALS
Decals associated with the safe operation of this equipment
are defined below.
DANGER
Flying Objects Hazard
DO NOT disassemble spring cylinders without
qualified service personnel. Possibility exists
of severe bodily harm and injury.
DANGER
No Water Warning
DO NOT add water to the retardant tank.
DANGER
Belt Guard Hazard
DO NOT remove belt guards.
Keep hands and fingers clear from engine belts.
Moving parts can crush.
DANGER
Training
This machine to be operated by qualified
personnel only. Ask for training as needed.
DANGER
Inhalation Hazard
DO NOT use this equipment in an enclosed area.
The engine used with this equipment emits
harmful levels of carbon monoxide which can
cause severe bodily harm — even death!
DANGER
Rotating Blade Hazard
Keep hands, fingers, and feet clear of engine
fan blades and guard rings. Moving parts can cut.
DO NOT remove guards.
Stop engine before servicing.
P/N 23808
P/N 36099
P/N 23700
NOTICE
Read Manual
To avoid injury, you must read and understand
the operator’s manual before using this machine.
NOTICE
Protective Clothing
ALWAYS wear appropriate clothing
when operating the trowel.
NOTICE
Lifting Location
Attach a suitable lifting device here to lift the unit.
UNLEADED GASOLINE
The engine used in this equipment
runs on unleaded gasoline.
CAUTION
Burn Hazard
HOT PARTS can burn skin.
DO NOT touch hot parts.
Allow machine sufficient amount of time to cool
before performing maintenance.
WARNING
Lifting/Crush Hazard
NEVER allow any person to stand
underneath the trowel while lifting.
DO NOT lift trowel with pans attached.
ALWAYS make sure handle is securely attached.

PAGE 10 — JWN-SERIES RIDE-ON POWER TROWEL • OPERATION MANUAL — REV. #3 (08/30/19)
SAFETY INFORMATION
GENERAL SAFETY
CAUTION

NEVER operate this equipment without proper protective
clothing, shatterproof glasses, respiratory protection,
hearing protection, steel-toed boots and other protective
devices required by the job or city and state regulations.

Avoid wearing jewelry or loose fitting clothes that may
snag on the controls or moving parts as this can cause
serious injury.

NEVER operate this equipment when not
feeling well due to fatigue, illness or when
under medication.

NEVER operate this equipment under the
influence of drugs or alcohol.

ALWAYS clear the work area of any debris, tools, etc.
that would constitute a hazard while the equipment is
in operation.

No one other than the operator is to be in the working
area when the equipment is in operation.

DO NOT use the equipment for any purpose other than
its intended purposes or applications.
NOTICE

This equipment should only be operated by trained and
qualified personnel 18 years of age and older.

Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.

Manufacturer does not assume responsibility for any
accident due to equipment modifications. Unauthorized
equipment modification will void all warranties.
NEVER
use accessories or attachments that are not
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
ALWAYS know the location of the nearest
fire extinguisher.
ALWAYS know the location of the nearest
first aid kit.
ALWAYS know the location of the nearest phone or
keep
a phone on the job site.
Also, know the phone numbers
of the nearest ambulance, doctor and
fire department.
This information will be invaluable in the case of an
emergency.