MULTISPAN CPR 126-1C User manual

CPR 126-1C
CURRENT PROTECTION RELAY
TECHNICAL SPECIFICATION
MECHANICAL INSTALLATION
TERMINAL CONNECTION
FEATURES:
INPUT SPECIFICATION:
DISPLAY AND KEY:
OUTPUT SPECIFICATION:
AUXILIARY SUPPLY:
GENERAL SPECIFICATION:
Primary CT value
True RMS Measurement
Protection available
Over Load
Auto/Manual /ZVR (Zero Value Reset) reset option
Under Load
3 digit bright LED display
Three phase current display with LED indication
Auto save out feature
Time parameter : Power on delay
Trip delay
Initial time delay
Recovery time (Auto reset)
Secondary current AC
Resolution
5 to 999 Selectable
0.5 to 5 Amp AC
0.01A, 0.1A, 1A
Display
Relay
Supply voltage
Dimension (mm)
Keys
Relay Type
Power consumption
(VA RATING)
Rating
Trip Setting
Time parameter
3 digit, 1line, 7 seg, 0.4” RED LED
1 nos.
75 (H) x 45 (W) x 110 (D) mm
SET, INC, DEC/ RST
1 C/O (NO-C-NC)
3 VA @ 230V AC MAX
10A, 230V AC/28 V DC
Under current : 0.00 to 100% of
primary C.T value
Trip delay time : 0 to 999 sec
Power on time : 0 to 99 sec
Initial time delay : 0 to 99 sec
Over current : 0.00 - 125% of
primary C.T value
ENVIRONMENT CONDITION:
Relative Humidity
Operating Temp. 0°C to 55°C
UP to 95% RH
(non-condensing)
100 to 270V AC, 50-60Hz
Recovery time : 0 to 99 sec
110
Front View(mm)
A
SET
NO
LNCNC
CPR 126-1C
R
40 0
75
Side View(mm)
75
45
NO
LNCNC
CPR 126-1C
R
A
SET
L1
L2
L3
N
TO
LOAD
Class 1.0 (Standard)
ACCURACY
Page -1

KEY OPERATION
Read complete instructions prior to installation
and operation of the unit.
WARNING : Risk of electric shock.
All safety related codifications, symbols and instructions that
appear in this operating manual or on the equipment must be
strictly followed to ensure the safety of the operating personnel
as well as the instrument.
If all the equipment is not handled in a manner specified by
the manufacturer, it might impair the protection provided by the
equipment.
MECHANICAL INSTALLATION GUIDELINES
MAINTENANCE
1. The equipment should be cleaned regularly to avoid
blockage of ventilating parts.
2. Clean the equipment with a clean soft cloth. Do not use
isopropyl alcohol or any other cleaning agent.
3. Fusible resistor must not be replaced by operator.
Page -2
Relay R
ØLED INDICATION
DISPLAY PAGE
1) L1-Phase current
4. 2 5
R
1) To install the instrument on a DIN rail, raise the clamp at
the back of the instrument and place it on the rail. Now
release the clamp, so the instrument fits on the DIN rail.
2) Ensure proper fitting of the instrument by pulling it
outwards.
3) To remove the instrument raise the clamp to release it
from the DIN rail.
4) The equipment in its installed state must not come in
close proximity to any heating source, caustic vapors, oil
steam, or other unwanted process byproducts.
5) Do not connect anything to unused terminals.
INSTALLATION GUIDELINES
1) Do not allow pieces of metal, wire clippings, or fine
metallic fillings from installation to enter the product or
else it may lead to a safety hazard that may in turn
endanger life or cause electrical shock to the operator.
2) Circuit breaker or mains switch must be installed
between power source and supply terminal to facilitate
power ‘ON’ or ‘OFF’ function. However this mains switch
or circuit breaker must be installed at convenient place
normally accessible to the operator.
3) Use and store the instrument within the specified ambient
temperature and humidity ranges as mentioned in this
manual.
SAFETY PRECAUTION
!
WARNING GUIDELINES
WARNING : Risk of electric shock.
1) To prevent the risk of electric shock, power supply to the
equipment must be kept OFF while doing the wiring
arrangement. Do not touch the terminals while power is
being supplied.
2) To reduce electro magnetic interference, use wire with
adequate rating and twists of the same of equal size shall
be made with shortest connection.
3. Cable used for connection to power source, must have a
cross section of 1mm or greater. These wires should have
insulations capacity made of at least 1.5kV.
4) A better anti-noise effect can be expected by using
standard power supply cable for the instrument.
To enter in parameter setting
To reset the relay contact in
manual mode after tripping
PRESS KEYFUNCTION
OPERATOR MODE
PARAMETER SETTING MODE
It is used to set parameter value
and to be save & exit from menu
To increment value in parameter
setting
To decrement value in parameter
setting
For 5 sec
SET
SET

Password
Over current
(Enable/Disable)
(Enable/Disable)
Press key for save & exit
Press key for save & exit
(Under Current)
Press key
Press key
Press key
Press key
Press key
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SETSET
SET
p a s
1 1
O C
e n b
u C
e n b
Password
If over current is enable
If under current is enable
If over current
is disable
If under
current
is disable
Over current
(Over current value)
(0.00 - 125% of
primary C.T Value)
(0.00 - 100% of
primary C.T Value)
(Under current value)
(Under Current)
Press key
Press key
Press key
Press key
Press key
p a s
7 3
O C
5 0 0
5 0 0
u C
Enter password 73
Enter password 11
Press key
for 5 sec
SET
Press key
for 5 sec
NOTE :-
- If Auxiliary supply cut out without fault Reset, Then
fault will be display at next power on.
SET
- To Reset fault press key.
O C O C
R
3 4 5
R
Scroll
Over current
Value = 34.5 A
◘
U C
R
1 0 0
R
Scroll
Under current
Value = 10.0 A
◘
Password 11 : To Enable / Disable trip parameter
(Over current, Under current,
Asymmetry, Single phase prevention)
Password 73 : To set trip value of Over current,
Under current, Asymmetry percentage
Password 37 : To set Power on time, ITD, Trip delay time,
reset Mode,Relay Fault mode,Power Fail
Fault Memory ,C.T ratio
1 1
FAULT MESSAGE
PARAMETER SETTING
Page -3

CONTROL FUNCTION
Password
Power on time
(0-99 sec)
(0-99 sec)
(0-999 sec)
(Relay fault mode)
Primary C.T ratio
Power Fault Memory
(On/Off)
(5-999 AmP)
ON / OFF
Press key for save & exit
(Initial time delay)
(Trip delay time)
Press key
Press key
Press key
Press key
Press key
Press key
Press key
SET
SET
SET
SET
SET
SET
SET
SET
p a s
3 7
P O N
2 0
I T D
2 5
T D L
2
R F m
C T R
P F M
O N
5
O N
Enter password 37
Press key
for 5 sec
SET
Press key
Press key
SET
SET
Press key
SET
Press key
Press key
Press key
Press key
SET
SET
SET
SET
a u t
r S t
r C t
5
(Auto / Manual / ZVR)
(Reset mode)
(Recovery time)
Press key
Press key
Press key
SET
SET
SET
If
manual reset
mode select
(0 to 99 sec.)
If Auto/ZVR reset mode select
Under Current Under Current - Enable
RLY fault - OFF
Power on time = 5 sec Initial time delay = 5 sec
Trip delay time = 5 sec Reset mode = Manual
Over Current Over Current - Enable
RLY fault - OFF
Specifications are subject to change, since development is a continuous process,
So for more updated operating information and Support,
Please contact our Helpline: 9978991474/76/82 or
Email at Ver:01122020[email protected]
Current
U.C Set point
OFF
TRP
Time
ON
5 10 15 20
Power
On ITD
TRP
Delay
OFF
Current
O.C Set point
Time
5 10 15 20
Power
On ITD
OFF
TRP
ON
OFF
L1
TRP
Delay
L1
Page -4